RE: [PATCH v2] OMAP3EVM: ehci: Fix EHCI support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

For the comment what about:
Set the VAUX2 regulator supply to 1.8V for the HSUSB host interface.
Tps65950 GPIO2 has to be set to zero in order to enable the EHCI select
line.

I see this patch as a fix for the EHCI support, what would you suggest
for the patch name?

Bryan
> Hi,
> > TPS65950 GPIO2 is to choose through u131 if we drive the lines to the
> > evm mother board or to the expansion connector p18. Should not it be
> > default to the mother board?
> It's not enabled by default and that’s why we need to enable it through
> Tps65950 GPIO2.
> 
> Your patch looks fine but the comment and name needs to be changed as
> There is no clock which gets enabled using gpio2. All the HSUSB clocks
> Are handled inside driver at drivers/usb/host/ehci-omap.c
> 
> Ajay
> 
> > The EHCI port on the mother board works with this patch.
> > 
> > Bryan
> > 
> > > Hi,
> > > > Set the VAUX2 regulator supply to 1.8V for the HSUSB host
> > interface.
> > > > Gpio 2 of the TPS65950 has to be set to zero in order to enable the
> > > > HSUBS2 clock.
> > >
> > > TPS65950 GPIO2 is not to enable HSUSB2 clock but to enable chip u131
> > > On omap3evm (rev-G) which latches USB, camera and audio lines.
> > >
> > > >
> > > > Signed-off-by: Bryan DE FARIA <bdefaria@xxxxxxxxxxxxxxxxxxx>
> > > > ---
> > > >  arch/arm/mach-omap2/board-omap3evm.c |   25
> > +++++++++++++++++++++++++
> > > >  1 files changed, 25 insertions(+), 0 deletions(-)
> > > >
> > > > diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-
> > > > omap2/board-omap3evm.c
> > > > index c452b3f..13a2b71 100644
> > > > --- a/arch/arm/mach-omap2/board-omap3evm.c
> > > > +++ b/arch/arm/mach-omap2/board-omap3evm.c
> > > > @@ -377,6 +377,10 @@ static int omap3evm_twl_gpio_setup(struct
> > device
> > > > *dev,
> > > >  	if (r)
> > > >  		printk(KERN_ERR "failed to get/set lcd_bkl gpio\n");
> > > >
> > > > +	/* gpio + 2 == HSUSB2 Clock Enable */
> > > > +	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
> > > > +		gpio_request_one(gpio + 2, GPIOF_OUT_INIT_LOW,
> > > > "EN_HSUSB2_CLK");
> > > > +
> > >
> > > Did you test EHCI port with this change ?
> > >
> > > Ajay
> > > >  	/* gpio + 7 == DVI Enable */
> > > >  	gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
> > > [...]
> > > rm-kernel
> 

--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux