On Thursday 04 August 2011 04:34 PM, Tarun Kanti DebBarma wrote:
From: Charulatha V<charu@xxxxxx>
Currently gpio_context array used to save gpio bank's context, is used only for
OMAP3 architecture. Move gpio_context as part of gpio_bank structure so that it
can be specific to each gpio bank and can be used for any OMAP architecture
Signed-off-by: Charulatha V<charu@xxxxxx>
---
Few comments.
drivers/gpio/gpio-omap.c | 76 ++++++++++++++++++++-------------------------
1 files changed, 34 insertions(+), 42 deletions(-)
diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index aaf07b8..2fa8b13 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -30,6 +30,19 @@
static LIST_HEAD(omap_gpio_list);
+struct gpio_regs {
+ u32 irqenable1;
+ u32 irqenable2;
+ u32 wake_en;
+ u32 ctrl;
+ u32 oe;
+ u32 leveldetect0;
+ u32 leveldetect1;
+ u32 risingdetect;
+ u32 fallingdetect;
+ u32 dataout;
debounce and debounce_en registers are missing.
Add them please.
+};
+
struct gpio_bank {
struct list_head node;
unsigned long pbase;
@@ -43,7 +56,7 @@ struct gpio_bank {
#endif
u32 non_wakeup_gpios;
u32 enabled_non_wakeup_gpios;
-
+ struct gpio_regs context;
u32 saved_datain;
u32 saved_fallingdetect;
u32 saved_risingdetect;
@@ -66,23 +79,6 @@ struct gpio_bank {
struct omap_gpio_reg_offs *regs;
};
-#ifdef CONFIG_ARCH_OMAP3
-struct omap3_gpio_regs {
- u32 irqenable1;
- u32 irqenable2;
- u32 wake_en;
- u32 ctrl;
- u32 oe;
- u32 leveldetect0;
- u32 leveldetect1;
- u32 risingdetect;
- u32 fallingdetect;
- u32 dataout;
-};
-
-static struct omap3_gpio_regs gpio_context[OMAP34XX_NR_GPIOS];
-#endif
-
#define GPIO_INDEX(bank, gpio) (gpio % bank->width)
#define GPIO_BIT(bank, gpio) (1<< GPIO_INDEX(bank, gpio))
@@ -1494,33 +1490,31 @@ void omap2_gpio_resume_after_idle(void)
void omap_gpio_save_context(void)
{
struct gpio_bank *bank;
- int i = 0;
list_for_each_entry(bank,&omap_gpio_list, node) {
- i++;
if (!bank->loses_context)
continue;
- gpio_context[i].irqenable1 =
+ bank->context.irqenable1 =
__raw_readl(bank->base + OMAP24XX_GPIO_IRQENABLE1);
- gpio_context[i].irqenable2 =
+ bank->context.irqenable2 =
__raw_readl(bank->base + OMAP24XX_GPIO_IRQENABLE2);
The context restore procedure should be done carefully. For instance
IRQ enabled register should be restored last to avoid any spurious
interrupts.
- gpio_context[i].wake_en =
+ bank->context.wake_en =
__raw_readl(bank->base + OMAP24XX_GPIO_WAKE_EN);
- gpio_context[i].ctrl =
+ bank->context.ctrl =
__raw_readl(bank->base + OMAP24XX_GPIO_CTRL);
- gpio_context[i].oe =
+ bank->context.oe =
__raw_readl(bank->base + OMAP24XX_GPIO_OE);
Restore dataout register before OE restore.
- gpio_context[i].leveldetect0 =
+ bank->context.leveldetect0 =
__raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT0);
- gpio_context[i].leveldetect1 =
+ bank->context.leveldetect1 =
__raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT1);
- gpio_context[i].risingdetect =
+ bank->context.risingdetect =
__raw_readl(bank->base + OMAP24XX_GPIO_RISINGDETECT);
- gpio_context[i].fallingdetect =
+ bank->context.fallingdetect =
__raw_readl(bank->base + OMAP24XX_GPIO_FALLINGDETECT);
- gpio_context[i].dataout =
+ bank->context.dataout =
__raw_readl(bank->base + OMAP24XX_GPIO_DATAOUT);
}
}
Regards
Santosh
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
