Re: [PATCH v3 08/20] GPIO: OMAP: Use wkup regs off/suspend support flag

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Tarun Kanti DebBarma <tarun.kanti@xxxxxx> writes:

> From: Charulatha V <charu@xxxxxx>
>
> Wakeup register offsets are initialized according to OMAP versions
> during device registration. These explicit checks are no longer needed.
>
> mpuio_init() function is defined under #ifdefs. It is required only in case
> of MPUIO bank type and only when PM operations are supported by it.
> This is applicable only in case of OMAP16xx SoC's MPUIO GPIO bank type.
> For all the other cases it is a dummy function. Hence clean up the same
> and remove all the OMAP SoC specific #ifdefs.
>
> bank_is_mpuio() is defined as a check to identify if the bank type is MPUIO.
> It is not required to define it separately as zero for OMAP2plus. Remove this.

The MPUIO stuff should really be separated from the wkup register stuff.

[...]

> @@ -596,27 +594,11 @@ static void omap_gpio_free(struct gpio_chip *chip, unsigned offset)
>  	unsigned long flags;
>  
>  	spin_lock_irqsave(&bank->lock, flags);
> -#ifdef CONFIG_ARCH_OMAP16XX
> -	if (bank->method == METHOD_GPIO_1610) {
> -		/* Disable wake-up during idle for dynamic tick */
> -		void __iomem *reg = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA;
> -		__raw_writel(1 << offset, reg);
> -	}
> -#endif
> -#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
> -	if (bank->method == METHOD_GPIO_24XX) {
> -		/* Disable wake-up during idle for dynamic tick */
> -		void __iomem *reg = bank->base + OMAP24XX_GPIO_CLEARWKUENA;
> -		__raw_writel(1 << offset, reg);
> -	}
> -#endif
> -#ifdef CONFIG_ARCH_OMAP4
> -	if (bank->method == METHOD_GPIO_44XX) {
> +
> +	if (bank->regs->wkup_clear)
>  		/* Disable wake-up during idle for dynamic tick */
> -		void __iomem *reg = bank->base + OMAP4_GPIO_IRQWAKEN0;
> -		__raw_writel(1 << offset, reg);
> -	}
> -#endif
> +		__raw_writel(1 << offset, bank->base + bank->regs->wkup_clear);
> +

Note that this is not an equivalent change.  The current code is using
IRQWAKEN0 register and you're changing it to use the CLEARWKUPENA
register.

While the current code is clearly broken since it's not doing a
read/modify/write, this change is not very clear either, and not
documented in the changelog.

I think a better approach is to just drop the parts of this patch where
the wkup_set and wkup_clear registers are added.  Since they are removed
in patch 12/20 anyways, maybe moving 12/20 earlier in the series
would make this clearer and avoid unnessary additions followed by
removals.

Kevin
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux