The RSTCTRL register was accessed using an absolute address.
The usage of hardcoded macros to calculate virtual address from physical
one should be avoided as much as possible.
The usage of an offset will allow future improvement like migration from
the current architecture code toward a module driver.
Update prm_xxx accessors, move definition to the proper header file and
update copyrights.
Change the s16 register offset parameter to u16.
Signed-off-by: Benoit Cousson <b-cousson@xxxxxx>
Cc: Paul Walmsley <paul@xxxxxxxxx>
Cc: Rajendra Nayak <rnayak@xxxxxx>
---
arch/arm/mach-omap2/omap_hwmod.c | 19 ++++--
arch/arm/mach-omap2/omap_hwmod_44xx_data.c | 16 ++--
arch/arm/mach-omap2/prm44xx.c | 93 +-------------------------
arch/arm/mach-omap2/prm44xx.h | 4 -
arch/arm/mach-omap2/prminst44xx.c | 89 ++++++++++++++++++++++++-
arch/arm/mach-omap2/prminst44xx.h | 10 +++-
arch/arm/plat-omap/include/plat/omap_hwmod.h | 3 +-
7 files changed, 121 insertions(+), 113 deletions(-)
diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c
index 8ac2546..5c0169c 100644
--- a/arch/arm/mach-omap2/omap_hwmod.c
+++ b/arch/arm/mach-omap2/omap_hwmod.c
@@ -148,6 +148,7 @@
#include "cminst44xx.h"
#include "prm2xxx_3xxx.h"
#include "prm44xx.h"
+#include "prminst44xx.h"
#include "mux.h"
/* Maximum microseconds to wait for OMAP module to softreset */
@@ -1110,8 +1111,10 @@ static int _assert_hardreset(struct omap_hwmod *oh, const char *name)
return omap2_prm_assert_hardreset(oh->prcm.omap2.module_offs,
ohri.rst_shift);
else if (cpu_is_omap44xx())
- return omap4_prm_assert_hardreset(oh->prcm.omap4.rstctrl_reg,
- ohri.rst_shift);
+ return omap4_prm_assert_hardreset(ohri.rst_shift,
+ oh->clkdm->pwrdm.ptr->prcm_partition,
+ oh->clkdm->pwrdm.ptr->prcm_offs,
+ oh->prcm.omap4.rstctrl_offs);
else
return -EINVAL;
}
@@ -1146,8 +1149,10 @@ static int _deassert_hardreset(struct omap_hwmod *oh, const char *name)
if (ohri.st_shift)
pr_err("omap_hwmod: %s: %s: hwmod data error: OMAP4 does not support st_shift\n",
oh->name, name);
- ret = omap4_prm_deassert_hardreset(oh->prcm.omap4.rstctrl_reg,
- ohri.rst_shift);
+ ret = omap4_prm_deassert_hardreset(ohri.rst_shift,
+ oh->clkdm->pwrdm.ptr->prcm_partition,
+ oh->clkdm->pwrdm.ptr->prcm_offs,
+ oh->prcm.omap4.rstctrl_offs);
} else {
return -EINVAL;
}
@@ -1182,8 +1187,10 @@ static int _read_hardreset(struct omap_hwmod *oh, const char *name)
return omap2_prm_is_hardreset_asserted(oh->prcm.omap2.module_offs,
ohri.st_shift);
} else if (cpu_is_omap44xx()) {
- return omap4_prm_is_hardreset_asserted(oh->prcm.omap4.rstctrl_reg,
- ohri.rst_shift);
+ return omap4_prm_is_hardreset_asserted(ohri.rst_shift,
+ oh->clkdm->pwrdm.ptr->prcm_partition,
+ oh->clkdm->pwrdm.ptr->prcm_offs,
+ oh->prcm.omap4.rstctrl_offs);
} else {
return -EINVAL;
}
diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
index e4e50a8..1c0c96a 100644
--- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
@@ -1141,7 +1141,7 @@ static struct omap_hwmod omap44xx_dsp_c0_hwmod = {
.rst_lines_cnt = ARRAY_SIZE(omap44xx_dsp_c0_resets),
.prcm = {
.omap4 = {
- .rstctrl_reg = OMAP4430_RM_TESLA_RSTCTRL,
+ .rstctrl_offs = OMAP4_RM_TESLA_RSTCTRL_OFFSET,
},
},
.omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP44XX),
@@ -1159,7 +1159,7 @@ static struct omap_hwmod omap44xx_dsp_hwmod = {
.prcm = {
.omap4 = {
.clkctrl_offs = OMAP4_CM_TESLA_TESLA_CLKCTRL_OFFSET,
- .rstctrl_reg = OMAP4430_RM_TESLA_RSTCTRL,
+ .rstctrl_offs = OMAP4_RM_TESLA_RSTCTRL_OFFSET,
},
},
.slaves = omap44xx_dsp_slaves,
@@ -2481,7 +2481,7 @@ static struct omap_hwmod omap44xx_ipu_c0_hwmod = {
.rst_lines_cnt = ARRAY_SIZE(omap44xx_ipu_c0_resets),
.prcm = {
.omap4 = {
- .rstctrl_reg = OMAP4430_RM_DUCATI_RSTCTRL,
+ .rstctrl_offs = OMAP4_RM_DUCATI_RSTCTRL_OFFSET,
},
},
.omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP44XX),
@@ -2497,7 +2497,7 @@ static struct omap_hwmod omap44xx_ipu_c1_hwmod = {
.rst_lines_cnt = ARRAY_SIZE(omap44xx_ipu_c1_resets),
.prcm = {
.omap4 = {
- .rstctrl_reg = OMAP4430_RM_DUCATI_RSTCTRL,
+ .rstctrl_offs = OMAP4_RM_DUCATI_RSTCTRL_OFFSET,
},
},
.omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP44XX),
@@ -2515,7 +2515,7 @@ static struct omap_hwmod omap44xx_ipu_hwmod = {
.prcm = {
.omap4 = {
.clkctrl_offs = OMAP4_CM_DUCATI_DUCATI_CLKCTRL_OFFSET,
- .rstctrl_reg = OMAP4430_RM_DUCATI_RSTCTRL,
+ .rstctrl_offs = OMAP4_RM_DUCATI_RSTCTRL_OFFSET,
},
},
.slaves = omap44xx_ipu_slaves,
@@ -2681,7 +2681,7 @@ static struct omap_hwmod omap44xx_iva_seq0_hwmod = {
.rst_lines_cnt = ARRAY_SIZE(omap44xx_iva_seq0_resets),
.prcm = {
.omap4 = {
- .rstctrl_reg = OMAP4430_RM_IVAHD_RSTCTRL,
+ .rstctrl_offs = OMAP4_RM_IVAHD_RSTCTRL_OFFSET,
},
},
.omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP44XX),
@@ -2697,7 +2697,7 @@ static struct omap_hwmod omap44xx_iva_seq1_hwmod = {
.rst_lines_cnt = ARRAY_SIZE(omap44xx_iva_seq1_resets),
.prcm = {
.omap4 = {
- .rstctrl_reg = OMAP4430_RM_IVAHD_RSTCTRL,
+ .rstctrl_offs = OMAP4_RM_IVAHD_RSTCTRL_OFFSET,
},
},
.omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP44XX),
@@ -2715,7 +2715,7 @@ static struct omap_hwmod omap44xx_iva_hwmod = {
.prcm = {
.omap4 = {
.clkctrl_offs = OMAP4_CM_IVAHD_IVAHD_CLKCTRL_OFFSET,
- .rstctrl_reg = OMAP4430_RM_IVAHD_RSTCTRL,
+ .rstctrl_offs = OMAP4_RM_IVAHD_RSTCTRL_OFFSET,
},
},
.slaves = omap44xx_iva_slaves,
diff --git a/arch/arm/mach-omap2/prm44xx.c b/arch/arm/mach-omap2/prm44xx.c
index a2a04bf..faec860 100644
--- a/arch/arm/mach-omap2/prm44xx.c
+++ b/arch/arm/mach-omap2/prm44xx.c
@@ -1,7 +1,7 @@
/*
* OMAP4 PRM module functions
*
- * Copyright (C) 2010 Texas Instruments, Inc.
+ * Copyright (C) 2011 Texas Instruments, Inc.
* Copyright (C) 2010 Nokia Corporation
* Benoît Cousson
* Paul Walmsley
@@ -24,12 +24,6 @@
#include "prm44xx.h"
#include "prm-regbits-44xx.h"
-/*
- * Address offset (in bytes) between the reset control and the reset
- * status registers: 4 bytes on OMAP4
- */
-#define OMAP4_RST_CTRL_ST_OFFSET 4
-
/* PRM low-level functions */
/* Read a register in a CM/PRM instance in the PRM module */
@@ -94,91 +88,6 @@ u32 omap4_prm_clear_inst_reg_bits(u32 bits, s16 inst, s16 reg)
return omap4_prm_rmw_inst_reg_bits(bits, 0x0, inst, reg);
}
-/**
- * omap4_prm_is_hardreset_asserted - read the HW reset line state of
- * submodules contained in the hwmod module
- * @rstctrl_reg: RM_RSTCTRL register address for this module
- * @shift: register bit shift corresponding to the reset line to check
- *
- * Returns 1 if the (sub)module hardreset line is currently asserted,
- * 0 if the (sub)module hardreset line is not currently asserted, or
- * -EINVAL upon parameter error.
- */
-int omap4_prm_is_hardreset_asserted(void __iomem *rstctrl_reg, u8 shift)
-{
- if (!cpu_is_omap44xx() || !rstctrl_reg)
- return -EINVAL;
-
- return omap4_prm_read_bits_shift(rstctrl_reg, (1 << shift));
-}
-
-/**
- * omap4_prm_assert_hardreset - assert the HW reset line of a submodule
- * @rstctrl_reg: RM_RSTCTRL register address for this module
- * @shift: register bit shift corresponding to the reset line to assert
- *
- * Some IPs like dsp, ipu or iva contain processors that require an HW
- * reset line to be asserted / deasserted in order to fully enable the
- * IP. These modules may have multiple hard-reset lines that reset
- * different 'submodules' inside the IP block. This function will
- * place the submodule into reset. Returns 0 upon success or -EINVAL
- * upon an argument error.
- */
-int omap4_prm_assert_hardreset(void __iomem *rstctrl_reg, u8 shift)
-{
- u32 mask;
-
- if (!cpu_is_omap44xx() || !rstctrl_reg)
- return -EINVAL;
-
- mask = 1 << shift;
- omap4_prm_rmw_reg_bits(mask, mask, rstctrl_reg);
-
- return 0;
-}
-
-/**
- * omap4_prm_deassert_hardreset - deassert a submodule hardreset line and wait
- * @rstctrl_reg: RM_RSTCTRL register address for this module
- * @shift: register bit shift corresponding to the reset line to deassert
- *
- * Some IPs like dsp, ipu or iva contain processors that require an HW
- * reset line to be asserted / deasserted in order to fully enable the
- * IP. These modules may have multiple hard-reset lines that reset
- * different 'submodules' inside the IP block. This function will
- * take the submodule out of reset and wait until the PRCM indicates
- * that the reset has completed before returning. Returns 0 upon success or
- * -EINVAL upon an argument error, -EEXIST if the submodule was already out
- * of reset, or -EBUSY if the submodule did not exit reset promptly.
- */
-int omap4_prm_deassert_hardreset(void __iomem *rstctrl_reg, u8 shift)
-{
- u32 mask;
- void __iomem *rstst_reg;
- int c;
-
- if (!cpu_is_omap44xx() || !rstctrl_reg)
- return -EINVAL;
-
- rstst_reg = rstctrl_reg + OMAP4_RST_CTRL_ST_OFFSET;
-
- mask = 1 << shift;
-
- /* Check the current status to avoid de-asserting the line twice */
- if (omap4_prm_read_bits_shift(rstctrl_reg, mask) == 0)
- return -EEXIST;
-
- /* Clear the reset status by writing 1 to the status bit */
- omap4_prm_rmw_reg_bits(0xffffffff, mask, rstst_reg);
- /* de-assert the reset control line */
- omap4_prm_rmw_reg_bits(mask, 0, rstctrl_reg);
- /* wait the status to be set */
- omap_test_timeout(omap4_prm_read_bits_shift(rstst_reg, mask),
- MAX_MODULE_HARDRESET_WAIT, c);
-
- return (c == MAX_MODULE_HARDRESET_WAIT) ? -EBUSY : 0;
-}
-
void omap4_prm_global_warm_sw_reset(void)
{
u32 v;
diff --git a/arch/arm/mach-omap2/prm44xx.h b/arch/arm/mach-omap2/prm44xx.h
index 11e878f..21b0240 100644
--- a/arch/arm/mach-omap2/prm44xx.h
+++ b/arch/arm/mach-omap2/prm44xx.h
@@ -691,10 +691,6 @@ extern u32 omap4_prm_set_inst_reg_bits(u32 bits, s16 inst, s16 idx);
extern u32 omap4_prm_clear_inst_reg_bits(u32 bits, s16 inst, s16 idx);
extern u32 omap4_prm_read_bits_shift(void __iomem *reg, u32 mask);
-extern int omap4_prm_is_hardreset_asserted(void __iomem *rstctrl_reg, u8 shift);
-extern int omap4_prm_assert_hardreset(void __iomem *rstctrl_reg, u8 shift);
-extern int omap4_prm_deassert_hardreset(void __iomem *rstctrl_reg, u8 shift);
-
extern void omap4_prm_global_warm_sw_reset(void);
# endif
diff --git a/arch/arm/mach-omap2/prminst44xx.c b/arch/arm/mach-omap2/prminst44xx.c
index a303242..67e9e46 100644
--- a/arch/arm/mach-omap2/prminst44xx.c
+++ b/arch/arm/mach-omap2/prminst44xx.c
@@ -2,6 +2,7 @@
* OMAP4 PRM instance functions
*
* Copyright (C) 2009 Nokia Corporation
+ * Copyright (C) 2011 Texas Instruments, Inc.
* Paul Walmsley
*
* This program is free software; you can redistribute it and/or modify
@@ -53,7 +54,7 @@ void omap4_prminst_write_inst_reg(u32 val, u8 part, s16 inst, u16 idx)
/* Read-modify-write a register in PRM. Caller must lock */
u32 omap4_prminst_rmw_inst_reg_bits(u32 mask, u32 bits, u8 part, s16 inst,
- s16 idx)
+ u16 idx)
{
u32 v;
@@ -64,3 +65,89 @@ u32 omap4_prminst_rmw_inst_reg_bits(u32 mask, u32 bits, u8 part, s16 inst,
return v;
}
+
+/*
+ * Address offset (in bytes) between the reset control and the reset
+ * status registers: 4 bytes on OMAP4
+ */
+#define OMAP4_RST_CTRL_ST_OFFSET 4
+
+/**
+ * omap4_prm_is_hardreset_asserted - read the HW reset line state of
+ * submodules contained in the hwmod module
+ * @rstctrl_reg: RM_RSTCTRL register address for this module
+ * @shift: register bit shift corresponding to the reset line to check
+ *
+ * Returns 1 if the (sub)module hardreset line is currently asserted,
+ * 0 if the (sub)module hardreset line is not currently asserted, or
+ * -EINVAL upon parameter error.
+ */
+int omap4_prm_is_hardreset_asserted(u8 shift, u8 part, s16 inst,
+ u16 rstctrl_offs)
+{
+ u32 v;
+
+ v = omap4_prminst_read_inst_reg(part, inst, rstctrl_offs);
+ v &= 1 << shift;
+ v >>= shift;
+
+ return v;
+}
+
+/**
+ * omap4_prm_assert_hardreset - assert the HW reset line of a submodule
+ * @rstctrl_reg: RM_RSTCTRL register address for this module
+ * @shift: register bit shift corresponding to the reset line to assert
+ *
+ * Some IPs like dsp, ipu or iva contain processors that require an HW
+ * reset line to be asserted / deasserted in order to fully enable the
+ * IP. These modules may have multiple hard-reset lines that reset
+ * different 'submodules' inside the IP block. This function will
+ * place the submodule into reset. Returns 0 upon success or -EINVAL
+ * upon an argument error.
+ */
+int omap4_prm_assert_hardreset(u8 shift, u8 part, s16 inst,
+ u16 rstctrl_offs)
+{
+ u32 mask = 1 << shift;
+
+ omap4_prminst_rmw_inst_reg_bits(mask, mask, part, inst, rstctrl_offs);
+
+ return 0;
+}
+
+/**
+ * omap4_prm_deassert_hardreset - deassert a submodule hardreset line and wait
+ * @rstctrl_reg: RM_RSTCTRL register address for this module
+ * @shift: register bit shift corresponding to the reset line to deassert
+ *
+ * Some IPs like dsp, ipu or iva contain processors that require an HW
+ * reset line to be asserted / deasserted in order to fully enable the
+ * IP. These modules may have multiple hard-reset lines that reset
+ * different 'submodules' inside the IP block. This function will
+ * take the submodule out of reset and wait until the PRCM indicates
+ * that the reset has completed before returning. Returns 0 upon success or
+ * -EINVAL upon an argument error, -EEXIST if the submodule was already out
+ * of reset, or -EBUSY if the submodule did not exit reset promptly.
+ */
+int omap4_prm_deassert_hardreset(u8 shift, u8 part, s16 inst,
+ u16 rstctrl_offs)
+{
+ int c;
+ u32 mask = 1 << shift;
+ u16 rstst_offs = rstctrl_offs + OMAP4_RST_CTRL_ST_OFFSET;
+
+ /* Check the current status to avoid de-asserting the line twice */
+ if (omap4_prm_is_hardreset_asserted(mask, part, inst, rstctrl_offs) == 0)
+ return -EEXIST;
+
+ /* Clear the reset status by writing 1 to the status bit */
+ omap4_prminst_rmw_inst_reg_bits(0xffffffff, mask, part, inst, rstst_offs);
+ /* de-assert the reset control line */
+ omap4_prminst_rmw_inst_reg_bits(mask, 0, part, inst, rstst_offs);
+ /* wait the status to be set */
+ omap_test_timeout(omap4_prm_is_hardreset_asserted(mask, part, inst, rstst_offs),
+ MAX_MODULE_HARDRESET_WAIT, c);
+
+ return (c == MAX_MODULE_HARDRESET_WAIT) ? -EBUSY : 0;
+}
diff --git a/arch/arm/mach-omap2/prminst44xx.h b/arch/arm/mach-omap2/prminst44xx.h
index 02dd66d..80e930e 100644
--- a/arch/arm/mach-omap2/prminst44xx.h
+++ b/arch/arm/mach-omap2/prminst44xx.h
@@ -2,6 +2,7 @@
* OMAP4 Power/Reset Management (PRM) function prototypes
*
* Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2011 Texas Instruments, Inc.
* Paul Walmsley
*
* This program is free software; you can redistribute it and/or modify
@@ -18,8 +19,15 @@
extern u32 omap4_prminst_read_inst_reg(u8 part, s16 inst, u16 idx);
extern void omap4_prminst_write_inst_reg(u32 val, u8 part, s16 inst, u16 idx);
extern u32 omap4_prminst_rmw_inst_reg_bits(u32 mask, u32 bits, u8 part,
- s16 inst, s16 idx);
+ s16 inst, u16 idx);
extern void omap4_prm_global_warm_sw_reset(void);
+extern int omap4_prm_is_hardreset_asserted(u8 shift, u8 part, s16 inst,
+ u16 rstctrl_offs);
+extern int omap4_prm_assert_hardreset(u8 shift, u8 part, s16 inst,
+ u16 rstctrl_offs);
+extern int omap4_prm_deassert_hardreset(u8 shift, u8 part, s16 inst,
+ u16 rstctrl_offs);
+
#endif
diff --git a/arch/arm/plat-omap/include/plat/omap_hwmod.h b/arch/arm/plat-omap/include/plat/omap_hwmod.h
index 22864fd..75bf4fa 100644
--- a/arch/arm/plat-omap/include/plat/omap_hwmod.h
+++ b/arch/arm/plat-omap/include/plat/omap_hwmod.h
@@ -2,6 +2,7 @@
* omap_hwmod macros, structures
*
* Copyright (C) 2009-2011 Nokia Corporation
+ * Copyright (C) 2011 Texas Instruments, Inc.
* Paul Walmsley
*
* Created in collaboration with (alphabetical order): Benoît Cousson,
@@ -363,7 +364,7 @@ struct omap_hwmod_omap2_prcm {
*/
struct omap_hwmod_omap4_prcm {
u16 clkctrl_offs;
- void __iomem *rstctrl_reg;
+ u16 rstctrl_offs;
u8 submodule_wkdep_bit;
};
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
