The pad values here are same as the default pad values updated in
serial.c file.
Avoid structure duplication and use default pads.
Signed-off-by: Govindraj.R <govindraj.raja@xxxxxx>
---
arch/arm/mach-omap2/board-3430sdp.c | 100 +----------------------------------
1 files changed, 1 insertions(+), 99 deletions(-)
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index 2b44c86..4e2baf7 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -553,106 +553,8 @@ static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
-
-static struct omap_device_pad serial1_pads[] __initdata = {
- /*
- * Note that off output enable is an active low
- * signal. So setting this means pin is a
- * input enabled in off mode
- */
- OMAP_MUX_STATIC("uart1_cts.uart1_cts",
- OMAP_PIN_INPUT |
- OMAP_PIN_OFF_INPUT_PULLDOWN |
- OMAP_OFFOUT_EN |
- OMAP_MUX_MODE0),
- OMAP_MUX_STATIC("uart1_rts.uart1_rts",
- OMAP_PIN_OUTPUT |
- OMAP_OFF_EN |
- OMAP_MUX_MODE0),
- OMAP_MUX_STATIC("uart1_rx.uart1_rx",
- OMAP_PIN_INPUT |
- OMAP_PIN_OFF_INPUT_PULLDOWN |
- OMAP_OFFOUT_EN |
- OMAP_MUX_MODE0),
- OMAP_MUX_STATIC("uart1_tx.uart1_tx",
- OMAP_PIN_OUTPUT |
- OMAP_OFF_EN |
- OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial2_pads[] __initdata = {
- OMAP_MUX_STATIC("uart2_cts.uart2_cts",
- OMAP_PIN_INPUT_PULLUP |
- OMAP_PIN_OFF_INPUT_PULLDOWN |
- OMAP_OFFOUT_EN |
- OMAP_MUX_MODE0),
- OMAP_MUX_STATIC("uart2_rts.uart2_rts",
- OMAP_PIN_OUTPUT |
- OMAP_OFF_EN |
- OMAP_MUX_MODE0),
- OMAP_MUX_STATIC("uart2_rx.uart2_rx",
- OMAP_PIN_INPUT |
- OMAP_PIN_OFF_INPUT_PULLDOWN |
- OMAP_OFFOUT_EN |
- OMAP_MUX_MODE0),
- OMAP_MUX_STATIC("uart2_tx.uart2_tx",
- OMAP_PIN_OUTPUT |
- OMAP_OFF_EN |
- OMAP_MUX_MODE0),
-};
-
-static struct omap_device_pad serial3_pads[] __initdata = {
- OMAP_MUX_STATIC("uart3_cts_rctx.uart3_cts_rctx",
- OMAP_PIN_INPUT_PULLDOWN |
- OMAP_PIN_OFF_INPUT_PULLDOWN |
- OMAP_OFFOUT_EN |
- OMAP_MUX_MODE0),
- OMAP_MUX_STATIC("uart3_rts_sd.uart3_rts_sd",
- OMAP_PIN_OUTPUT |
- OMAP_OFF_EN |
- OMAP_MUX_MODE0),
- OMAP_MUX_STATIC("uart3_rx_irrx.uart3_rx_irrx",
- OMAP_PIN_INPUT |
- OMAP_PIN_OFF_INPUT_PULLDOWN |
- OMAP_OFFOUT_EN |
- OMAP_MUX_MODE0),
- OMAP_MUX_STATIC("uart3_tx_irtx.uart3_tx_irtx",
- OMAP_PIN_OUTPUT |
- OMAP_OFF_EN |
- OMAP_MUX_MODE0),
-};
-
-static struct omap_board_data serial1_data = {
- .id = 0,
- .pads = serial1_pads,
- .pads_cnt = ARRAY_SIZE(serial1_pads),
-};
-
-static struct omap_board_data serial2_data = {
- .id = 1,
- .pads = serial2_pads,
- .pads_cnt = ARRAY_SIZE(serial2_pads),
-};
-
-static struct omap_board_data serial3_data = {
- .id = 2,
- .pads = serial3_pads,
- .pads_cnt = ARRAY_SIZE(serial3_pads),
-};
-
-static inline void board_serial_init(void)
-{
- omap_serial_init_port(&serial1_data, NULL);
- omap_serial_init_port(&serial2_data, NULL);
- omap_serial_init_port(&serial3_data, NULL);
-}
#else
#define board_mux NULL
-
-static inline void board_serial_init(void)
-{
- omap_serial_init();
-}
#endif
/*
@@ -789,7 +691,7 @@ static void __init omap_3430sdp_init(void)
else
gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV1;
omap_ads7846_init(1, gpio_pendown, 310, NULL);
- board_serial_init();
+ omap_serial_init();
usb_musb_init(NULL);
board_smc91x_init();
board_flash_init(sdp_flash_partitions, chip_sel_3430, 0);
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
