On 05/18/11 18:06, Steve Calfee wrote:
> On 05/16/11 23:37, Jarkko Nikula wrote:
>>>
>> Did you try to run OMAP as an I2S master like what omap3pandora.c is
>> doing?
>>
>> Missing clock in codec master configuration suggests that reason
>> is in codec side and reversed roles during development makes easier to
>> hunt it further as then OMAP can play data out independently of is the
>> codec correctly configured or not.
>>
>> You could run OMAP as a master by specifying SND_SOC_DAIFMT_CBS_CFS
>> as a DAI format for both codec and OMAP and by setting McBSP to use
>> internal 96 MHz clock as a master clock. Something like below might work
>> for testing purposes:
>>
>> snd_soc_dai_set_sysclk(cpu_dai, OMAP_MCBSP_SYSCLK_CLKS_FCLK,
>> 96000000, SND_SOC_CLOCK_IN);
>>
>> snd_soc_dai_set_clkdiv(cpu_dai, OMAP_MCBSP_CLKGDV,
>> 62); /* 96M / 48k*32 */
>>
> Hi,
>
> The hunt for clock continues. I redid my board-omap3beaglexm.c to as
> closely match what board-omap3pandora.c is doing as I can. Like pandora,
> I don't explicitly set the mux pin directions, I guess mcbsp master is
> the default.
>
> I also tried to get as close as I could to the soc/omap/omap3pandora.c
> machine driver with my omap3beaglexm.c machine driver. Specifically in
> the *_hw_params init routines.
>
> But when I start things up (even with the codec disconnected from the
> bclk line), I don't get any movement on the CLK and fsx. And of course
> the dma doesn't send anything.
>
I have gotten mcbsp1 to work as a slave (sort-of) with Peter's help. I
havent been able to get it to clock as a master. So now I try with
mcbsp3, still no luck.
More missing mcbsp bit clock. I am trying on mcbsp3. I am trying to get
master mode working. Here is the register dump from the console (I have
some debug printouts on).
[ 30.039978] snd_pcm_do_start: state 3
[ 30.043823] omap_pcm_trigger: cmd 1
[ 30.047760] omap_start_dma: lch 0
[ 30.051696] omap-mcbsp omap-mcbsp.3: **** McBSP3 regs ****
[ 30.057464] omap-mcbsp omap-mcbsp.3: DRR2: 0x2820d81
[ 30.062774] omap-mcbsp omap-mcbsp.3: DRR1: 0x0000
[ 30.067779] omap-mcbsp omap-mcbsp.3: DXR2: 0x0000
[ 30.072814] omap-mcbsp omap-mcbsp.3: DXR1: 0x0000
[ 30.077850] omap-mcbsp omap-mcbsp.3: SPCR2: 0x02f5
[ 30.082885] omap-mcbsp omap-mcbsp.3: SPCR1: 0x0030
[ 30.087890] omap-mcbsp omap-mcbsp.3: RCR2: 0x80a1
[ 30.092926] omap-mcbsp omap-mcbsp.3: RCR1: 0x00a0
[ 30.097961] omap-mcbsp omap-mcbsp.3: XCR2: 0x80a1
[ 30.102966] omap-mcbsp omap-mcbsp.3: XCR1: 0x00a0
[ 30.108001] omap-mcbsp omap-mcbsp.3: SRGR2: 0x10c0
[ 30.113037] omap-mcbsp omap-mcbsp.3: SRGR1: 0x5f3d
[ 30.118041] omap-mcbsp omap-mcbsp.3: PCR0: 0x0f0f
[ 30.123077] omap-mcbsp omap-mcbsp.3: ***********************
My BSP sets up the mux for mcbsp3:
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
#if 1
/* McBSP 1 slave */
OMAP3_MUX(MCBSP1_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(MCBSP1_CLKX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(MCBSP1_DR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(MCBSP1_DX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
#else
/* McBSP 1 master */
OMAP3_MUX(MCBSP1_FSX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(MCBSP1_CLKX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(MCBSP1_DR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(MCBSP1_DX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
#endif
/* McBSP 3 master */
OMAP3_MUX(MCBSP3_FSX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(MCBSP3_CLKX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(MCBSP3_DR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(MCBSP3_DX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif
And with the mcbsp 4 pins not connected to anything but the scope, I
don't see any bitclock movement. I think others used u-boot to setup the
mcbspx, but has anyone successfully used linux to set up the pins?
Thanks, Steve
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
