Add IGEP3 machine support to board-igep0020
Signed-off-by: Mike Rapoport <mike@xxxxxxxxxxxxxx>
---
arch/arm/mach-omap2/board-igep0020.c | 103 ++++++++++++++++++++++++++--------
1 files changed, 80 insertions(+), 23 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index ea7cbc6..0d6d583 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -55,6 +55,11 @@
#define IGEP2_RC_GPIO_WIFI_NRESET 139
#define IGEP2_RC_GPIO_BT_NRESET 137
+#define IGEP3_GPIO_LED0_GREEN 54
+#define IGEP3_GPIO_LED0_RED 53
+#define IGEP3_GPIO_LED1_RED 16
+#define IGEP3_GPIO_USBH_NRESET 183
+
/*
* IGEP2 Hardware Revision Table
*
@@ -69,6 +74,7 @@
#define IGEP2_BOARD_HWREV_B 0
#define IGEP2_BOARD_HWREV_C 1
+#define IGEP3_BOARD_HWREV 2
static u8 hwrev;
@@ -76,6 +82,11 @@ static void __init igep2_get_revision(void)
{
u8 ret;
+ if (machine_is_igep0030()) {
+ hwrev = IGEP3_BOARD_HWREV;
+ return;
+ }
+
omap_mux_init_gpio(IGEP2_GPIO_LED1_RED, OMAP_PIN_INPUT);
if (gpio_request_one(IGEP2_GPIO_LED1_RED, GPIOF_IN, "GPIO_HW0_REV")) {
@@ -332,24 +343,40 @@ static struct platform_device igep_led_device = {
static void __init igep_leds_init(void)
{
- igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED;
- igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN;
- igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED;
+ if (machine_is_igep0020()) {
+ igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED;
+ igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN;
+ igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED;
+ } else {
+ igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED;
+ igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN;
+ igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED;
+ }
platform_device_register(&igep_led_device);
}
#else
static struct gpio igep_gpio_leds[] __initdata = {
- { IGEP2_GPIO_LED0_RED, GPIOF_OUT_INIT_LOW, "gpio-led:red:d0" },
- { IGEP2_GPIO_LED0_GREEN, GPIOF_OUT_INIT_LOW, "gpio-led:green:d0" },
- { IGEP2_GPIO_LED1_RED, GPIOF_OUT_INIT_LOW, "gpio-led:red:d1" },
+ { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d0" },
+ { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:green:d0" },
+ { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d1" },
};
static inline void igep_leds_init(void)
{
int i;
+ if (machine_is_igep0020()) {
+ igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED;
+ igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN;
+ igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED;
+ } else {
+ igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED;
+ igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN;
+ igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED;
+ }
+
if (gpio_request_array(igep_gpio_leds, ARRAY_SIZE(igep_gpio_leds))) {
pr_warning("IGEP v2: Could not obtain leds gpios\n");
return;
@@ -386,6 +413,9 @@ static int igep_twl_gpio_setup(struct device *dev,
igep_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
#endif
+ if (machine_is_igep0030())
+ return 0;
+
/*
* REVISIT: need ehci-omap hooks for external VBUS
* power switch and overcurrent detect
@@ -548,18 +578,20 @@ static void __init igep_i2c_init(void)
{
int ret;
- /*
- * Bus 3 is attached to the DVI port where devices like the pico DLP
- * projector don't work reliably with 400kHz
- */
- ret = omap_register_i2c_bus(3, 100, igep2_i2c3_boardinfo,
- ARRAY_SIZE(igep2_i2c3_boardinfo));
- if (ret)
- pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret);
-
- igep_twldata.codec = &igep2_codec_data;
- igep_twldata.keypad = &igep2_keypad_pdata;
- igep_twldata.vpll2 = &igep2_vpll2;
+ if (machine_is_igep0020()) {
+ /*
+ * Bus 3 is attached to the DVI port where devices like the
+ * pico DLP projector don't work reliably with 400kHz
+ */
+ ret = omap_register_i2c_bus(3, 100, igep2_i2c3_boardinfo,
+ ARRAY_SIZE(igep2_i2c3_boardinfo));
+ if (ret)
+ pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret);
+
+ igep_twldata.codec = &igep2_codec_data;
+ igep_twldata.keypad = &igep2_keypad_pdata;
+ igep_twldata.vpll2 = &igep2_vpll2;
+ }
omap3_pmic_init("twl4030", &igep_twldata);
}
@@ -575,6 +607,17 @@ static const struct usbhs_omap_board_data igep2_usbhs_bdata __initconst = {
.reset_gpio_port[2] = -EINVAL,
};
+static const struct usbhs_omap_board_data igep3_usbhs_bdata __initconst = {
+ .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = IGEP3_GPIO_USBH_NRESET,
+ .reset_gpio_port[2] = -EINVAL,
+};
+
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
@@ -597,7 +640,7 @@ static void __init igep_wlan_bt_init(void)
igep_wlan_bt_gpios[0].gpio = IGEP2_RB_GPIO_WIFI_NPD;
igep_wlan_bt_gpios[1].gpio = IGEP2_RB_GPIO_WIFI_NRESET;
igep_wlan_bt_gpios[2].gpio = IGEP2_RB_GPIO_BT_NRESET;
- } else if (hwrev == IGEP2_BOARD_HWREV_C) {
+ } else if (hwrev == IGEP2_BOARD_HWREV_C || machine_is_igep0030()) {
igep_wlan_bt_gpios[0].gpio = IGEP2_RC_GPIO_WIFI_NPD;
igep_wlan_bt_gpios[1].gpio = IGEP2_RC_GPIO_WIFI_NRESET;
igep_wlan_bt_gpios[2].gpio = IGEP2_RC_GPIO_BT_NRESET;
@@ -645,10 +688,14 @@ static void __init igep_init(void)
*/
igep_wlan_bt_init();
- omap_display_init(&igep2_dss_data);
- igep2_display_init();
- igep2_init_smsc911x();
- usbhs_init(&igep2_usbhs_bdata);
+ if (machine_is_igep0020()) {
+ omap_display_init(&igep2_dss_data);
+ igep2_display_init();
+ igep2_init_smsc911x();
+ usbhs_init(&igep2_usbhs_bdata);
+ } else {
+ usbhs_init(&igep3_usbhs_bdata);
+ }
}
MACHINE_START(IGEP0020, "IGEP v2 board")
@@ -660,3 +707,13 @@ MACHINE_START(IGEP0020, "IGEP v2 board")
.init_machine = igep_init,
.timer = &omap_timer,
MACHINE_END
+
+MACHINE_START(IGEP0030, "IGEP OMAP3 module")
+ .boot_params = 0x80000100,
+ .reserve = omap_reserve,
+ .map_io = omap3_map_io,
+ .init_early = igep_init_early,
+ .init_irq = omap_init_irq,
+ .init_machine = igep_init,
+ .timer = &omap_timer,
+MACHINE_END
--
1.7.3.1
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
