IGEP2 and IGEP3 boards are very similar and can be merged into one file.
Start refactoring with changing igep2 to igep where applicable.
Signed-off-by: Mike Rapoport <mike@xxxxxxxxxxxxxx>
---
arch/arm/mach-omap2/board-igep0020.c | 158 +++++++++++++++++-----------------
1 files changed, 79 insertions(+), 79 deletions(-)
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index c62c297e..ad20f7b 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -112,7 +112,7 @@ static void __init igep2_get_revision(void)
* So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
*/
-static struct mtd_partition igep2_onenand_partitions[] = {
+static struct mtd_partition igep_onenand_partitions[] = {
{
.name = "X-Loader",
.offset = 0,
@@ -140,21 +140,21 @@ static struct mtd_partition igep2_onenand_partitions[] = {
},
};
-static struct omap_onenand_platform_data igep2_onenand_data = {
- .parts = igep2_onenand_partitions,
- .nr_parts = ARRAY_SIZE(igep2_onenand_partitions),
+static struct omap_onenand_platform_data igep_onenand_data = {
+ .parts = igep_onenand_partitions,
+ .nr_parts = ARRAY_SIZE(igep_onenand_partitions),
.dma_channel = -1, /* disable DMA in OMAP OneNAND driver */
};
-static struct platform_device igep2_onenand_device = {
+static struct platform_device igep_onenand_device = {
.name = "omap2-onenand",
.id = -1,
.dev = {
- .platform_data = &igep2_onenand_data,
+ .platform_data = &igep_onenand_data,
},
};
-static void __init igep2_flash_init(void)
+static void __init igep_flash_init(void)
{
u8 cs = 0;
u8 onenandcs = GPMC_CS_NUM + 1;
@@ -166,7 +166,7 @@ static void __init igep2_flash_init(void)
/* Check if NAND/oneNAND is configured */
if ((ret & 0xC00) == 0x800)
/* NAND found */
- pr_err("IGEP2: Unsupported NAND found\n");
+ pr_err("IGEP: Unsupported NAND found\n");
else {
ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7);
if ((ret & 0x3F) == (ONENAND_MAP >> 24))
@@ -176,18 +176,18 @@ static void __init igep2_flash_init(void)
}
if (onenandcs > GPMC_CS_NUM) {
- pr_err("IGEP2: Unable to find configuration in GPMC\n");
+ pr_err("IGEP: Unable to find configuration in GPMC\n");
return;
}
- igep2_onenand_data.cs = onenandcs;
+ igep_onenand_data.cs = onenandcs;
- if (platform_device_register(&igep2_onenand_device) < 0)
- pr_err("IGEP2: Unable to register OneNAND device\n");
+ if (platform_device_register(&igep_onenand_device) < 0)
+ pr_err("IGEP: Unable to register OneNAND device\n");
}
#else
-static void __init igep2_flash_init(void) {}
+static void __init igep_flash_init(void) {}
#endif
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
@@ -211,11 +211,11 @@ static inline void __init igep2_init_smsc911x(void)
static inline void __init igep2_init_smsc911x(void) { }
#endif
-static struct regulator_consumer_supply igep2_vmmc1_supply =
+static struct regulator_consumer_supply igep_vmmc1_supply =
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0");
/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
-static struct regulator_init_data igep2_vmmc1 = {
+static struct regulator_init_data igep_vmmc1 = {
.constraints = {
.min_uV = 1850000,
.max_uV = 3150000,
@@ -226,13 +226,13 @@ static struct regulator_init_data igep2_vmmc1 = {
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = 1,
- .consumer_supplies = &igep2_vmmc1_supply,
+ .consumer_supplies = &igep_vmmc1_supply,
};
-static struct regulator_consumer_supply igep2_vio_supply =
+static struct regulator_consumer_supply igep_vio_supply =
REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.1");
-static struct regulator_init_data igep2_vio = {
+static struct regulator_init_data igep_vio = {
.constraints = {
.min_uV = 1800000,
.max_uV = 1800000,
@@ -244,34 +244,34 @@ static struct regulator_init_data igep2_vio = {
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = 1,
- .consumer_supplies = &igep2_vio_supply,
+ .consumer_supplies = &igep_vio_supply,
};
-static struct regulator_consumer_supply igep2_vmmc2_supply =
+static struct regulator_consumer_supply igep_vmmc2_supply =
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1");
-static struct regulator_init_data igep2_vmmc2 = {
+static struct regulator_init_data igep_vmmc2 = {
.constraints = {
.valid_modes_mask = REGULATOR_MODE_NORMAL,
.always_on = 1,
},
.num_consumer_supplies = 1,
- .consumer_supplies = &igep2_vmmc2_supply,
+ .consumer_supplies = &igep_vmmc2_supply,
};
-static struct fixed_voltage_config igep2_vwlan = {
+static struct fixed_voltage_config igep_vwlan = {
.supply_name = "vwlan",
.microvolts = 3300000,
.gpio = -EINVAL,
.enabled_at_boot = 1,
- .init_data = &igep2_vmmc2,
+ .init_data = &igep_vmmc2,
};
-static struct platform_device igep2_vwlan_device = {
+static struct platform_device igep_vwlan_device = {
.name = "reg-fixed-voltage",
.id = 0,
.dev = {
- .platform_data = &igep2_vwlan,
+ .platform_data = &igep_vwlan,
},
};
@@ -296,7 +296,7 @@ static struct omap2_hsmmc_info mmc[] = {
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
#include <linux/leds.h>
-static struct gpio_led igep2_gpio_leds[] = {
+static struct gpio_led igep_gpio_leds[] = {
[0] = {
.name = "gpio-led:red:d0",
.gpio = IGEP2_GPIO_LED0_RED,
@@ -320,34 +320,34 @@ static struct gpio_led igep2_gpio_leds[] = {
},
};
-static struct gpio_led_platform_data igep2_led_pdata = {
- .leds = igep2_gpio_leds,
- .num_leds = ARRAY_SIZE(igep2_gpio_leds),
+static struct gpio_led_platform_data igep_led_pdata = {
+ .leds = igep_gpio_leds,
+ .num_leds = ARRAY_SIZE(igep_gpio_leds),
};
-static struct platform_device igep2_led_device = {
+static struct platform_device igep_led_device = {
.name = "leds-gpio",
.id = -1,
.dev = {
- .platform_data = &igep2_led_pdata,
+ .platform_data = &igep_led_pdata,
},
};
-static void __init igep2_leds_init(void)
+static void __init igep_leds_init(void)
{
- platform_device_register(&igep2_led_device);
+ platform_device_register(&igep_led_device);
}
#else
-static struct gpio igep2_gpio_leds[] __initdata = {
+static struct gpio igep_gpio_leds[] __initdata = {
{ IGEP2_GPIO_LED0_RED, GPIOF_OUT_INIT_LOW, "gpio-led:red:d0" },
{ IGEP2_GPIO_LED0_GREEN, GPIOF_OUT_INIT_LOW, "gpio-led:green:d0" },
{ IGEP2_GPIO_LED1_RED, GPIOF_OUT_INIT_LOW, "gpio-led:red:d1" },
};
-static inline void igep2_leds_init(void)
+static inline void igep_leds_init(void)
{
- if (gpio_request_array(igep2_gpio_leds, ARRAY_SIZE(igep2_gpio_leds))) {
+ if (gpio_request_array(igep_gpio_leds, ARRAY_SIZE(igep_gpio_leds))) {
pr_warning("IGEP v2: Could not obtain leds gpios\n");
return;
}
@@ -363,7 +363,7 @@ static struct gpio igep2_twl_gpios[] = {
{ -EINVAL, GPIOF_OUT_INIT_LOW, "GPIO_USBH_CPEN" },
};
-static int igep2_twl_gpio_setup(struct device *dev,
+static int igep_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
int ret;
@@ -392,23 +392,23 @@ static int igep2_twl_gpio_setup(struct device *dev,
if (ret == 0)
gpio_export(gpio + TWL4030_GPIO_MAX + 1, 0);
else
- pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_GREEN\n");
+ pr_warning("IGEP: Could not obtain gpio GPIO_LED1_GREEN\n");
#else
- igep2_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
+ igep_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
#endif
return 0;
};
-static struct twl4030_gpio_platform_data igep2_twl4030_gpio_pdata = {
+static struct twl4030_gpio_platform_data igep_twl4030_gpio_pdata = {
.gpio_base = OMAP_MAX_GPIO_LINES,
.irq_base = TWL4030_GPIO_IRQ_BASE,
.irq_end = TWL4030_GPIO_IRQ_END,
.use_leds = true,
- .setup = igep2_twl_gpio_setup,
+ .setup = igep_twl_gpio_setup,
};
-static struct twl4030_usb_data igep2_usb_data = {
+static struct twl4030_usb_data igep_usb_data = {
.usb_mode = T2_USB_MODE_ULPI,
};
@@ -476,11 +476,11 @@ static void __init igep2_display_init(void)
pr_err("IGEP v2: Could not obtain gpio GPIO_DVI_PUP\n");
}
-static struct platform_device *igep2_devices[] __initdata = {
- &igep2_vwlan_device,
+static struct platform_device *igep_devices[] __initdata = {
+ &igep_vwlan_device,
};
-static void __init igep2_init_early(void)
+static void __init igep_init_early(void)
{
omap2_init_common_infrastructure();
omap2_init_common_devices(m65kxxxxam_sdrc_params,
@@ -525,18 +525,18 @@ static struct twl4030_keypad_data igep2_keypad_pdata = {
.rep = 1,
};
-static struct twl4030_platform_data igep2_twldata = {
+static struct twl4030_platform_data igep_twldata = {
.irq_base = TWL4030_IRQ_BASE,
.irq_end = TWL4030_IRQ_END,
/* platform_data for children goes here */
- .usb = &igep2_usb_data,
+ .usb = &igep_usb_data,
.codec = &igep2_codec_data,
- .gpio = &igep2_twl4030_gpio_pdata,
+ .gpio = &igep_twl4030_gpio_pdata,
.keypad = &igep2_keypad_pdata,
- .vmmc1 = &igep2_vmmc1,
+ .vmmc1 = &igep_vmmc1,
.vpll2 = &igep2_vpll2,
- .vio = &igep2_vio,
+ .vio = &igep_vio,
};
static struct i2c_board_info __initdata igep2_i2c3_boardinfo[] = {
@@ -545,11 +545,11 @@ static struct i2c_board_info __initdata igep2_i2c3_boardinfo[] = {
},
};
-static void __init igep2_i2c_init(void)
+static void __init igep_i2c_init(void)
{
int ret;
- omap3_pmic_init("twl4030", &igep2_twldata);
+ omap3_pmic_init("twl4030", &igep_twldata);
/*
* Bus 3 is attached to the DVI port where devices like the pico DLP
@@ -561,7 +561,7 @@ static void __init igep2_i2c_init(void)
pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret);
}
-static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
+static const struct usbhs_omap_board_data igep2_usbhs_bdata __initconst = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
@@ -579,64 +579,64 @@ static struct omap_board_mux board_mux[] __initdata = {
#endif
#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
-static struct gpio igep2_wlan_bt_gpios[] __initdata = {
+static struct gpio igep_wlan_bt_gpios[] __initdata = {
{ -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NPD" },
{ -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NRESET" },
{ -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_BT_NRESET" },
};
-static void __init igep2_wlan_bt_init(void)
+static void __init igep_wlan_bt_init(void)
{
int err;
/* GPIO's for WLAN-BT combo depends on hardware revision */
if (hwrev == IGEP2_BOARD_HWREV_B) {
- igep2_wlan_bt_gpios[0].gpio = IGEP2_RB_GPIO_WIFI_NPD;
- igep2_wlan_bt_gpios[1].gpio = IGEP2_RB_GPIO_WIFI_NRESET;
- igep2_wlan_bt_gpios[2].gpio = IGEP2_RB_GPIO_BT_NRESET;
+ igep_wlan_bt_gpios[0].gpio = IGEP2_RB_GPIO_WIFI_NPD;
+ igep_wlan_bt_gpios[1].gpio = IGEP2_RB_GPIO_WIFI_NRESET;
+ igep_wlan_bt_gpios[2].gpio = IGEP2_RB_GPIO_BT_NRESET;
} else if (hwrev == IGEP2_BOARD_HWREV_C) {
- igep2_wlan_bt_gpios[0].gpio = IGEP2_RC_GPIO_WIFI_NPD;
- igep2_wlan_bt_gpios[1].gpio = IGEP2_RC_GPIO_WIFI_NRESET;
- igep2_wlan_bt_gpios[2].gpio = IGEP2_RC_GPIO_BT_NRESET;
+ igep_wlan_bt_gpios[0].gpio = IGEP2_RC_GPIO_WIFI_NPD;
+ igep_wlan_bt_gpios[1].gpio = IGEP2_RC_GPIO_WIFI_NRESET;
+ igep_wlan_bt_gpios[2].gpio = IGEP2_RC_GPIO_BT_NRESET;
} else
return;
- err = gpio_request_array(igep2_wlan_bt_gpios,
- ARRAY_SIZE(igep2_wlan_bt_gpios));
+ err = gpio_request_array(igep_wlan_bt_gpios,
+ ARRAY_SIZE(igep_wlan_bt_gpios));
if (err) {
pr_warning("IGEP2: Could not obtain WIFI/BT gpios\n");
return;
}
- gpio_export(igep2_wlan_bt_gpios[0].gpio, 0);
- gpio_export(igep2_wlan_bt_gpios[1].gpio, 0);
- gpio_export(igep2_wlan_bt_gpios[2].gpio, 0);
+ gpio_export(igep_wlan_bt_gpios[0].gpio, 0);
+ gpio_export(igep_wlan_bt_gpios[1].gpio, 0);
+ gpio_export(igep_wlan_bt_gpios[2].gpio, 0);
- gpio_set_value(igep2_wlan_bt_gpios[1].gpio, 0);
+ gpio_set_value(igep_wlan_bt_gpios[1].gpio, 0);
udelay(10);
- gpio_set_value(igep2_wlan_bt_gpios[1].gpio, 1);
+ gpio_set_value(igep_wlan_bt_gpios[1].gpio, 1);
}
#else
-static inline void __init igep2_wlan_bt_init(void) { }
+static inline void __init igep_wlan_bt_init(void) { }
#endif
-static void __init igep2_init(void)
+static void __init igep_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
/* Get IGEP2 hardware revision */
igep2_get_revision();
/* Register I2C busses and drivers */
- igep2_i2c_init();
- platform_add_devices(igep2_devices, ARRAY_SIZE(igep2_devices));
+ igep_i2c_init();
+ platform_add_devices(igep_devices, ARRAY_SIZE(igep_devices));
omap_display_init(&igep2_dss_data);
omap_serial_init();
usb_musb_init(NULL);
- usbhs_init(&usbhs_bdata);
+ usbhs_init(&igep2_usbhs_bdata);
- igep2_flash_init();
- igep2_leds_init();
+ igep_flash_init();
+ igep_leds_init();
igep2_display_init();
igep2_init_smsc911x();
@@ -644,7 +644,7 @@ static void __init igep2_init(void)
* WLAN-BT combo module from MuRata which has a Marvell WLAN
* (88W8686) + CSR Bluetooth chipset. Uses SDIO interface.
*/
- igep2_wlan_bt_init();
+ igep_wlan_bt_init();
}
@@ -652,8 +652,8 @@ MACHINE_START(IGEP0020, "IGEP v2 board")
.boot_params = 0x80000100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
- .init_early = igep2_init_early,
+ .init_early = igep_init_early,
.init_irq = omap_init_irq,
- .init_machine = igep2_init,
+ .init_machine = igep_init,
.timer = &omap_timer,
MACHINE_END
--
1.7.3.1
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
