Hello.
Ajay Kumar Gupta wrote:
As the control.h have been moved to new location and it's
uses are not allowed to drivers directly so moving the phy
control, interrupt clear and reset functionality to board
files.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@xxxxxx>
[...]
diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c
index 7260558..1f32fdb 100644
--- a/arch/arm/mach-omap2/usb-musb.c
+++ b/arch/arm/mach-omap2/usb-musb.c
@@ -33,6 +33,82 @@
#ifdef CONFIG_USB_MUSB_SOC
+static void am35x_musb_phy_power(u8 on)
+{
+ unsigned long timeout = jiffies + msecs_to_jiffies(100);
+ u32 devconf2;
+
+ if (on) {
+ /*
+ * Start the on-chip PHY and its PLL.
+ */
+ devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
+
+ devconf2 &= ~(CONF2_RESET | CONF2_PHYPWRDN | CONF2_OTGPWRDN);
+ devconf2 |= CONF2_PHY_PLLON;
+
+ omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
+
+ printk(KERN_INFO "Waiting for PHY clock good...\n");
pr_info().
+ while (!(omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2)
+ & CONF2_PHYCLKGD)) {
+ cpu_relax();
+
+ if (time_after(jiffies, timeout)) {
+ printk(KERN_ERR "musb PHY clock good timed out\n");
pr_err().
diff --git a/arch/arm/plat-omap/include/plat/usb.h b/arch/arm/plat-omap/include/plat/usb.h
index 59c7fe7..4299097 100644
--- a/arch/arm/plat-omap/include/plat/usb.h
+++ b/arch/arm/plat-omap/include/plat/usb.h
@@ -69,6 +69,9 @@ struct omap_musb_board_data {
u8 mode;
u16 power;
unsigned extvbus:1;
+ void (*set_phy_power) (u8 on);
+ void (*clear_irq) (void);
+ void (*set_mode) (u8 mode);
Should be no spaces between ) and (. scripts/checkpatch.pl used to complain
about such things, now it's silent though...
@@ -364,37 +324,21 @@ eoi:
int musb_platform_set_mode(struct musb *musb, u8 musb_mode)
{
- u32 devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
+ struct device *dev = musb->controller;
+ struct musb_hdrc_platform_data *plat = dev->platform_data;
+ struct omap_musb_board_data *data = plat->board_data;
- devconf2 &= ~CONF2_OTGMODE;
- switch (musb_mode) {
-#ifdef CONFIG_USB_MUSB_HDRC_HCD
- case MUSB_HOST: /* Force VBUS valid, ID = 0 */
- devconf2 |= CONF2_FORCE_HOST;
- break;
-#endif
-#ifdef CONFIG_USB_GADGET_MUSB_HDRC
- case MUSB_PERIPHERAL: /* Force VBUS valid, ID = 1 */
- devconf2 |= CONF2_FORCE_DEVICE;
- break;
-#endif
-#ifdef CONFIG_USB_MUSB_OTG
- case MUSB_OTG: /* Don't override the VBUS/ID comparators */
- devconf2 |= CONF2_NO_OVERRIDE;
- break;
-#endif
- default:
- DBG(2, "Trying to set unsupported mode %u\n", musb_mode);
- }
+ if (data->set_mode)
+ data->set_mode(musb_mode);
You should return -EIO if data->set_mode is NULL.
WBR, Sergei
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
