Update the ehci-omap glue layer to support the controller in the
OMAP4. Major differences from OMAP3 is that the OMAP4 has per-port
clocking, and supports ULPI output clocking mode. The old input
clocking mode is not supported.
Also, there are only 2 externally available ports as against 3
in the OMAP3. The third port is internally tied off and should
not be used.
Signed-off-by: Keshava Munegowda <keshava_mgowda@xxxxxx>
Signed-off-by: Anand Gadiyar <gadiyar@xxxxxx>
---
drivers/usb/host/ehci-omap.c | 258 ++++++++++++++++++++++++++++++++++-------
1 files changed, 214 insertions(+), 44 deletions(-)
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index dd9d5c1..0374eb4 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -1,11 +1,12 @@
/*
- * ehci-omap.c - driver for USBHOST on OMAP 34xx processor
+ * ehci-omap.c - driver for USBHOST on OMAP3/4 processors
*
- * Bus Glue for OMAP34xx USBHOST 3 port EHCI controller
- * Tested on OMAP3430 ES2.0 SDP
+ * Bus Glue for the EHCI controllers in OMAP3/4
+ * Tested on several OMAP3 boards, and OMAP4 Pandaboard
*
- * Copyright (C) 2007-2008 Texas Instruments, Inc.
+ * Copyright (C) 2007-2010 Texas Instruments, Inc.
* Author: Vikram Pandita <vikram.pandita@xxxxxx>
+ * Author: Anand Gadiyar <gadiyar@xxxxxx>
*
* Copyright (C) 2009 Nokia Corporation
* Contact: Felipe Balbi <felipe.balbi@xxxxxxxxx>
@@ -26,11 +27,14 @@
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
- * TODO (last updated Feb 12, 2010):
+ * TODO (last updated Nov 21, 2010):
* - add kernel-doc
* - enable AUTOIDLE
* - add suspend/resume
* - move workarounds to board-files
+ * - factor out code common to OHCI
+ * - add HSIC and TLL support
+ * - convert to use hwmod and runtime PM
*/
#include <linux/platform_device.h>
@@ -114,6 +118,23 @@
#define OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS (1 << 9)
#define OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS (1 << 10)
+/* OMAP4-specific defines */
+#define OMAP4_UHH_SYSCONFIG_IDLEMODE_CLEAR (3 << 2)
+#define OMAP4_UHH_SYSCONFIG_NOIDLE (1 << 2)
+
+#define OMAP4_UHH_SYSCONFIG_STDBYMODE_CLEAR (3 << 4)
+#define OMAP4_UHH_SYSCONFIG_NOSTDBY (1 << 4)
+#define OMAP4_UHH_SYSCONFIG_SOFTRESET (1 << 0)
+
+#define OMAP4_P1_MODE_CLEAR (3 << 16)
+#define OMAP4_P1_MODE_TLL (1 << 16)
+#define OMAP4_P1_MODE_HSIC (3 << 16)
+#define OMAP4_P2_MODE_CLEAR (3 << 18)
+#define OMAP4_P2_MODE_TLL (1 << 18)
+#define OMAP4_P2_MODE_HSIC (3 << 18)
+
+#define OMAP_REV2_TLL_CHANNEL_COUNT 2
+
#define OMAP_UHH_DEBUG_CSR (0x44)
/* EHCI Register Set */
@@ -127,8 +148,16 @@
#define EHCI_INSNREG05_ULPI_EXTREGADD_SHIFT 8
#define EHCI_INSNREG05_ULPI_WRDATA_SHIFT 0
+/* Values of UHH_REVISION - Note: these are not given in the TRM */
+#define OMAP_EHCI_REV1 0x00000010 /* OMAP3 */
+#define OMAP_EHCI_REV2 0x50700100 /* OMAP4 */
+
+#define is_omap_ehci_rev1(x) (x->omap_ehci_rev == OMAP_EHCI_REV1)
+#define is_omap_ehci_rev2(x) (x->omap_ehci_rev == OMAP_EHCI_REV2)
+
#define is_ehci_phy_mode(x) (x == EHCI_HCD_OMAP_MODE_PHY)
#define is_ehci_tll_mode(x) (x == EHCI_HCD_OMAP_MODE_TLL)
+#define is_ehci_hsic_mode(x) (x == EHCI_HCD_OMAP_MODE_HSIC)
/*-------------------------------------------------------------------------*/
@@ -163,6 +192,10 @@ struct ehci_hcd_omap {
struct clk *usbhost_fs_fck;
struct clk *usbtll_fck;
struct clk *usbtll_ick;
+ struct clk *xclk60mhsp1_ck;
+ struct clk *xclk60mhsp2_ck;
+ struct clk *utmi_p1_fck;
+ struct clk *utmi_p2_fck;
/* FIXME the following two workarounds are
* board specific not silicon-specific so these
@@ -179,6 +212,9 @@ struct ehci_hcd_omap {
/* phy reset workaround */
int phy_reset;
+ /* IP revision */
+ u32 omap_ehci_rev;
+
/* desired phy_mode: TLL, PHY */
enum ehci_hcd_omap_mode port_mode[OMAP3_HS_USB_PORTS];
@@ -337,6 +373,80 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
}
clk_enable(omap->usbtll_ick);
+ omap->omap_ehci_rev = ehci_omap_readl(omap->uhh_base,
+ OMAP_UHH_REVISION);
+ dev_dbg(omap->dev, "OMAP UHH_REVISION 0x%x\n",
+ omap->omap_ehci_rev);
+
+ /*
+ * Enable per-port clocks as needed (newer controllers only).
+ * - External ULPI clock for PHY mode
+ * - Internal clocks for TLL and HSIC modes (TODO)
+ */
+ if (is_omap_ehci_rev2(omap)) {
+ switch (omap->port_mode[0]) {
+ case EHCI_HCD_OMAP_MODE_PHY:
+ omap->xclk60mhsp1_ck = clk_get(omap->dev,
+ "xclk60mhsp1_ck");
+ if (IS_ERR(omap->xclk60mhsp1_ck)) {
+ ret = PTR_ERR(omap->xclk60mhsp1_ck);
+ dev_err(omap->dev,
+ "Unable to get Port1 ULPI clock\n");
+ }
+
+ omap->utmi_p1_fck = clk_get(omap->dev,
+ "utmi_p1_gfclk");
+ if (IS_ERR(omap->utmi_p1_fck)) {
+ ret = PTR_ERR(omap->utmi_p1_fck);
+ dev_err(omap->dev,
+ "Unable to get utmi_p1_fck\n");
+ }
+
+ ret = clk_set_parent(omap->utmi_p1_fck,
+ omap->xclk60mhsp1_ck);
+ if (ret != 0) {
+ dev_err(omap->dev,
+ "Unable to set P1 f-clock\n");
+ }
+ break;
+ case EHCI_HCD_OMAP_MODE_TLL:
+ /* TODO */
+ default:
+ break;
+ }
+ switch (omap->port_mode[1]) {
+ case EHCI_HCD_OMAP_MODE_PHY:
+ omap->xclk60mhsp2_ck = clk_get(omap->dev,
+ "xclk60mhsp2_ck");
+ if (IS_ERR(omap->xclk60mhsp2_ck)) {
+ ret = PTR_ERR(omap->xclk60mhsp2_ck);
+ dev_err(omap->dev,
+ "Unable to get Port2 ULPI clock\n");
+ }
+
+ omap->utmi_p2_fck = clk_get(omap->dev,
+ "utmi_p2_gfclk");
+ if (IS_ERR(omap->utmi_p2_fck)) {
+ ret = PTR_ERR(omap->utmi_p2_fck);
+ dev_err(omap->dev,
+ "Unable to get utmi_p2_fck\n");
+ }
+
+ ret = clk_set_parent(omap->utmi_p2_fck,
+ omap->xclk60mhsp2_ck);
+ if (ret != 0) {
+ dev_err(omap->dev,
+ "Unable to set P2 f-clock\n");
+ }
+ break;
+ case EHCI_HCD_OMAP_MODE_TLL:
+ /* TODO */
+ default:
+ break;
+ }
+ }
+
+
/* perform TLL soft reset, and wait until reset is complete */
ehci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
OMAP_USBTLL_SYSCONFIG_SOFTRESET);
@@ -364,12 +474,20 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
/* Put UHH in NoIdle/NoStandby mode */
reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSCONFIG);
- reg |= (OMAP_UHH_SYSCONFIG_ENAWAKEUP
- | OMAP_UHH_SYSCONFIG_SIDLEMODE
- | OMAP_UHH_SYSCONFIG_CACTIVITY
- | OMAP_UHH_SYSCONFIG_MIDLEMODE);
- reg &= ~OMAP_UHH_SYSCONFIG_AUTOIDLE;
+ if (is_omap_ehci_rev1(omap)) {
+ reg |= (OMAP_UHH_SYSCONFIG_ENAWAKEUP
+ | OMAP_UHH_SYSCONFIG_SIDLEMODE
+ | OMAP_UHH_SYSCONFIG_CACTIVITY
+ | OMAP_UHH_SYSCONFIG_MIDLEMODE);
+ reg &= ~OMAP_UHH_SYSCONFIG_AUTOIDLE;
+
+ } else if (is_omap_ehci_rev2(omap)) {
+ reg &= ~OMAP4_UHH_SYSCONFIG_IDLEMODE_CLEAR;
+ reg |= OMAP4_UHH_SYSCONFIG_NOIDLE;
+ reg &= ~OMAP4_UHH_SYSCONFIG_STDBYMODE_CLEAR;
+ reg |= OMAP4_UHH_SYSCONFIG_NOSTDBY;
+ }
ehci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG, reg);
reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_HOSTCONFIG);
@@ -380,40 +498,56 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
| OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN);
reg &= ~OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN;
- if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_UNKNOWN)
- reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
- if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_UNKNOWN)
- reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
- if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_UNKNOWN)
- reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
-
- /* Bypass the TLL module for PHY mode operation */
- if (cpu_is_omap3430() && (omap_rev() <= OMAP3430_REV_ES2_1)) {
- dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1\n");
- if (is_ehci_phy_mode(omap->port_mode[0]) ||
- is_ehci_phy_mode(omap->port_mode[1]) ||
- is_ehci_phy_mode(omap->port_mode[2]))
- reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
- else
- reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
- } else {
- dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n");
- if (is_ehci_phy_mode(omap->port_mode[0]))
- reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
- else if (is_ehci_tll_mode(omap->port_mode[0]))
- reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
-
- if (is_ehci_phy_mode(omap->port_mode[1]))
- reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
- else if (is_ehci_tll_mode(omap->port_mode[1]))
- reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
-
- if (is_ehci_phy_mode(omap->port_mode[2]))
- reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
- else if (is_ehci_tll_mode(omap->port_mode[2]))
- reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
+ if (is_omap_ehci_rev1(omap)) {
+ if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_UNKNOWN)
+ reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
+ if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_UNKNOWN)
+ reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
+ if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_UNKNOWN)
+ reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
+
+ /* Bypass the TLL module for PHY mode operation */
+ if (cpu_is_omap3430() && (omap_rev() <= OMAP3430_REV_ES2_1)) {
+ dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1\n");
+ if (is_ehci_phy_mode(omap->port_mode[0]) ||
+ is_ehci_phy_mode(omap->port_mode[1]) ||
+ is_ehci_phy_mode(omap->port_mode[2]))
+ reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
+ else
+ reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
+ } else {
+ dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n");
+ if (is_ehci_phy_mode(omap->port_mode[0]))
+ reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
+ else if (is_ehci_tll_mode(omap->port_mode[0]))
+ reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
+
+ if (is_ehci_phy_mode(omap->port_mode[1]))
+ reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
+ else if (is_ehci_tll_mode(omap->port_mode[1]))
+ reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
+
+ if (is_ehci_phy_mode(omap->port_mode[2]))
+ reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
+ else if (is_ehci_tll_mode(omap->port_mode[2]))
+ reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
+ }
+ } else if (is_omap_ehci_rev2(omap)) {
+ /* Clear port mode fields for PHY mode*/
+ reg &= ~OMAP4_P1_MODE_CLEAR;
+ reg &= ~OMAP4_P2_MODE_CLEAR;
+
+ if (is_ehci_tll_mode(omap->port_mode[0]))
+ reg |= OMAP4_P1_MODE_TLL;
+ else if (is_ehci_hsic_mode(omap->port_mode[0]))
+ reg |= OMAP4_P1_MODE_HSIC;
+ if (is_ehci_tll_mode(omap->port_mode[1]))
+ reg |= OMAP4_P2_MODE_TLL;
+ else if (is_ehci_hsic_mode(omap->port_mode[1]))
+ reg |= OMAP4_P2_MODE_HSIC;
}
+
ehci_omap_writel(omap->uhh_base, OMAP_UHH_HOSTCONFIG, reg);
dev_dbg(omap->dev, "UHH setup done, uhh_hostconfig=%x\n", reg);
@@ -468,6 +602,14 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
return 0;
err_sys_status:
+ clk_disable(omap->utmi_p2_fck);
+ clk_put(omap->utmi_p2_fck);
+ clk_disable(omap->xclk60mhsp2_ck);
+ clk_put(omap->xclk60mhsp2_ck);
+ clk_disable(omap->utmi_p1_fck);
+ clk_put(omap->utmi_p1_fck);
+ clk_disable(omap->xclk60mhsp1_ck);
+ clk_put(omap->xclk60mhsp1_ck);
clk_disable(omap->usbtll_ick);
clk_put(omap->usbtll_ick);
@@ -507,6 +649,8 @@ static void omap_stop_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
/* Reset OMAP modules for insmod/rmmod to work */
ehci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG,
+ is_omap_ehci_rev2(omap) ?
+ OMAP4_UHH_SYSCONFIG_SOFTRESET :
OMAP_UHH_SYSCONFIG_SOFTRESET);
while (!(ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS)
& (1 << 0))) {
@@ -572,6 +716,32 @@ static void omap_stop_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
omap->usbtll_ick = NULL;
}
+ if (is_omap_ehci_rev2(omap)) {
+ if (omap->xclk60mhsp1_ck != NULL) {
+ clk_disable(omap->xclk60mhsp1_ck);
+ clk_put(omap->xclk60mhsp1_ck);
+ omap->xclk60mhsp1_ck = NULL;
+ }
+
+ if (omap->utmi_p1_fck != NULL) {
+ clk_disable(omap->utmi_p1_fck);
+ clk_put(omap->utmi_p1_fck);
+ omap->utmi_p1_fck = NULL;
+ }
+
+ if (omap->xclk60mhsp2_ck != NULL) {
+ clk_disable(omap->xclk60mhsp2_ck);
+ clk_put(omap->xclk60mhsp2_ck);
+ omap->xclk60mhsp2_ck = NULL;
+ }
+
+ if (omap->utmi_p2_fck != NULL) {
+ clk_disable(omap->utmi_p2_fck);
+ clk_put(omap->utmi_p2_fck);
+ omap->utmi_p2_fck = NULL;
+ }
+ }
+
if (omap->phy_reset) {
if (gpio_is_valid(omap->reset_gpio_port[0]))
gpio_free(omap->reset_gpio_port[0]);
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
