On Wednesday, October 27, 2010, Mathieu Desnoyers wrote:
> * Rafael J. Wysocki (rjw@xxxxxxx) wrote:
> > On Tuesday, October 26, 2010, Mathieu Desnoyers wrote:
> > > * Alan Stern (stern@xxxxxxxxxxxxxxxxxxx) wrote:
> > > > On Tue, 26 Oct 2010, Mathieu Desnoyers wrote:
> > > >
> > > > > * Peter Zijlstra (peterz@xxxxxxxxxxxxx) wrote:
> > > > > > On Tue, 2010-10-26 at 11:56 -0500, Pierre Tardy wrote:
> > > > > > >
> > > > > > > + trace_runtime_pm_usage(dev, atomic_read(&dev->power.usage_count)+1);
> > > > > > > atomic_inc(&dev->power.usage_count);
> > > > > >
> > > > > > That's terribly racy..
> > > > >
> > > > > Looking at the original code, it looks racy even without considering the
> > > > > tracepoint:
> > > > >
> > > > > int __pm_runtime_get(struct device *dev, bool sync)
> > > > > {
> > > > > int retval;
> > > > >
> > > > > + trace_runtime_pm_usage(dev, atomic_read(&dev->power.usage_count)+1);
> > > > > atomic_inc(&dev->power.usage_count);
> > > > > retval = sync ? pm_runtime_resume(dev) : pm_request_resume(dev);
> > > > >
> > > > > There is no implied memory barrier after "atomic_inc". So either all these
> > > > > inc/dec are protected with mutexes or spinlocks, in which case one might wonder
> > > > > why atomic operations are used at all, or it's a racy mess. (I vote for the
> > > > > second option)
> > > >
> > > > I don't understand. What's the problem? The inc/dec are atomic
> > > > because they are not protected by spinlocks, but everything else is
> > > > (aside from the tracepoint, which is new).
> > > >
> > > > > kref should certainly be used there.
> > > >
> > > > What for?
> > >
> > > kref has the following "get":
> > >
> > > atomic_inc(&kref->refcount);
> > > smp_mb__after_atomic_inc();
> > >
> > > What seems to be missing in __pm_runtime_get() and pm_runtime_get_noresume() is
> > > the memory barrier after the atomic increment. The atomic increment is free to
> > > be reordered into the following spinlock (within pm_request_resume or pm_request
> > > resume execution) because taking a spinlock only acts as a memory barrier with
> > > acquire semantic, not a full memory barrier.
> > >
> > > So AFAIU, the failure scenario would be as follows (sorry for the 80+ columns):
> > >
> > > initial conditions: usage_count = 1
> > >
> > > CPU A CPU B
> > > 1) __pm_runtime_get() (sync = true)
> > > 2) atomic_inc(&usage_count) (not committed to memory yet)
> > > 3) pm_runtime_resume()
> > > 4) spin_lock_irqsave(&dev->power.lock, flags);
> > > 5) retval = __pm_request_resume(dev);
> >
> > If sync = true this is
> > retval = __pm_runtime_resume(dev);
> > which drops and reacquires the spinlock.
>
> Let's see. Upon entry in __pm_runtime_resume, the following condition holds
> (remember, the initial condition is that usage_count == 1):
>
> dev->power.runtime_status == RPM_ACTIVE
>
> so retval is set to 1, which goto directly to "out", without setting "parent".
> So there does not seem to be any spinlock reacquire on this path, or am I
> misunderstanding how the "runtime_status" works ?
No, you're not I think, the above is correct. I was referring to the scenario
in which the device was RPM_SUSPENDED initially.
> > In the meantime it sets
> > ->power.runtime_status so that __pm_runtime_idle() will fail if run at this
> > point.
>
> runtime_status will be left at "RPM_ACTIVE", which is the appropriate value
> expected by __pm_runtime_idle.
>
> >
> > > 6) (execute the body of __pm_request_resume and return)
> > > 7) __pm_runtime_put() (sync = true)
> > > 8) if (atomic_dec_and_test(&dev->power.usage_count))
> > > (still see usage_count == 1 before decrement,
> > > thus decrement to 0)
> > > 9) pm_runtime_idle()
> > > 10) spin_unlock_irqrestore(&dev->power.lock, flags)
> > > 11) spin_lock_irq(&dev->power.lock);
> > > 12) retval = __pm_runtime_idle(dev);
> >
> > Moreover, __pm_runtime_idle() checks ->power.usage_count under the spinlock,
> > so it will see it's been incremented in the meantime and it will back off.
>
> This is a subtle but important point. Yes, my scenario seems to be dealt with by
> the extra usage_count check while the spinlock is held.
>
> How about adding a comment under this atomic_inc() stating that the memory
> barriers are implicitely dealt with by the following spinlock release and the
> extra check while spinlock is held ?
>
> Commenting memory barriers is important, but commenting why memory barriers are
> not needed due to a subtle corner-case looks even more important.
Well, given that this discussion is taking place at all, I admit that it would
be good to document this somehow. :-)
I'll take care of that.
> (hrm, but more below considering pm_runtime_get_noresume())
>
> >
> > > 13) spin_unlock_irq(&dev->power.lock);
> > >
> > > So we end up in a situation where CPU A expects the device to be resumed, but
> > > the last action performed has been to bring it to idle.
> > >
> > > A smp_mb__after_atomic_inc() between lines 2 and 3 would fix this.
> >
> > I don't think this particular race is possible. However, there is another one
> > that seems to be possible (in a different function) that an explicit barrier
> > will prevent from happening.
> >
> > It's related to pm_runtime_get_noresume(), but I think it's better to put the
> > barrier where it's necessary rather than into pm_runtime_get_noresume() itself.
>
> Quoting your following mail:
>
> > Actually, no. Since rpm_idle() and rpm_suspend() both check usage_count under
> > the spinlock, the race I was thinking about doesn't appear to be possible
> > after all.
>
> Hrm, for the extra-usage_count-under-spinlock check to work, all
> pm_runtime_get_noresume() callers should grab and release the dev->power.lock
> after incrementing the usage_count. This does not seem to be the case though. So
> you might really have a race there.
>
> So every code path that does:
>
> 1) pm_runtime_get_noresume(dev);
>
> 2) ...
>
> 3) pm_runtime_put_noidle(dev);
>
> expecting that the device state cannot be changed between 1 and 3 might be
> surprised by a concurrent call to __pm_runtime_idle() that would put a device to
> idle (or similarly with suspend) due to lack of memory barrier after the atomic
> increment.
>
> Or am I missing something else ?
First of all, the device can always be resumed regardless of the usage_count
value. usage_count is only used to block attempts to suspend the device and
execute its driver's ->runtime_idle() callback after it has been resumed.
That's why the "normal" pm_runtime_get() queues up a resume request.
IOW, the _get() only becomes meaningful after attempting to resume the device
(which is what I tried to tell Arjan in one of the previous messages).
Second, there's no synchronization between pm_runtime_get_noresume() and
pm_runtime_suspend/idle() etc., so calling pm_runtime_get_noresume() is
certainly insufficient to block pm_runtime_suspend/idle() regardless of memory
barriers (there may be one already in progress when _get_noresume() is called).
To limit possible status changes from happening one should (at least) run
pm_runtime_barrier() (surprise, no? ;-)) after pm_runtime_get_noresume().
So if you don't want to resume the device immediately after increasing its
usage_count (in which case it's better to use pm_runtime_get_sync()), you
should do something like this:
1) pm_runtime_get_noresume(dev);
1a) pm_runtime_barrier(dev); // That takes care of all pending requests etc.
2) ...
3) pm_runtime_put_noidle(dev);
[The meaning of pm_runtime_barrier() is that all of the runtime PM activity
started before the barrier has been completed when it returns.]
There's one place in the PM core where that really is necessary, but I wouldn't
recommend anyone doing anything like it in a driver.
Thanks,
Rafael
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
