On 10/07/2010 04:47 PM, Elvis Dowson wrote: > Hi, > I'm getting the following errors when attempting to use kgdb with the serial console. Any idea how I can resolve this issue? > > The correct serial parameters when I use kermit with the target board is > > set flow-control off > set carrier-watch none > set speed 115200 > > and it connects correctly. > > I'm not sure if the gdb configuration commands for the serial port are sufficient, and if there is a parameter that I am missing here. The host is connected to the target using an FTDI USB to serial converter, so it appears as /dev/ttyUSB0 on the host and as ttyS2 on the target. > > # su > # cd /tool/patches/android-rowboat-froyo-2.2-patchwork/kernel > # arm-angstrom-linux-gnueabi-gdb > (gdb) file vmlinux > Reading symbols from /tool/patches/android-rowboat-froyo-2.2-patchwork/kernel/vmlinux...done. > > (gdb) set remotebaud 115200 > (gdb) set remoteflow 0 > (gdb) set debug remote 1 > (gdb) set debug serial 1 > You don't want to use this one, it just tends to pollute the logs, "set debug remote 1" should be enough. > (gdb) target remote /dev/ttyUSB0 > > Looks to me like you did not activate the kernel debugger before using gdb to enter, because the gdb you are using is not going to send the "sysrq g" sequence. What you would want to do here is to "echo g > /proc/sysrq-trigger" with your terminal program, disconnect and then try connecting the debugger to the kernel. Another option is to use the agent-proxy so you can have a console connection and a debugger connection. It would probably also be good to test if the debugger is working at all on your serial port. Configure the debugger with: # echo ttyS2 > /sys/module/kgdboc/parameters/kgdboc kgdb: Registered I/O driver kgdboc. # echo g > /proc/sysrq-trigger SysRq : DEBUG And now to exit debugger you must blindly and perfectly type $D#44+ Nothing will be echoed because at this stage the kernel serial polling driver would just be collecting characters. After typing that the kernel should return back to the running state and print something like: +$OK#9a# Jason. > Remote debugging using /dev/ttyUSB0 > Sending packet: $qSupported#37...[ > r +]Ack > [$][q][S][u][p][p][o][r][t][e][d][#][3][7]Packet received: qSupported > Packet qSupported (supported-packets) is supported > warning: unrecognized item "qSupported" in "qSupported" response > Sending packet: $Hg0#df...[+]Ack > [$][H][g][0][#][d][f]Packet received: Hg0 > Sending packet: $?#3f...[+]Ack > [$][?][#][3][f]Packet received: ? > Sending packet: $Hc-1#09...[+]Ack > [$][H][c][-][1][#][0][9]Packet received: Hc-1 > Sending packet: $qC#b4...[+]Ack > [$][q][C][#][b][4]Packet received: qC > Sending packet: $qAttached#8f...[+]Ack > [$][q][A][t][t][a][c][h][e][d][#][8][f]Packet received: qAttached > Packet qAttached (query-attached) is supported > Sending packet: $qOffsets#4b...[+]Ack > [$][q][O][f][f][s][\r][\r][\n][e][t][s][#][4][b]Bad checksum, sentsum=0x4b, csum=0x6f, buf=qOffs\r\r\nets > [-][<Timeout: 2 seconds>]Timed out. > [-][<Timeout: 2 seconds>]Timed out. > Ignoring packet error, continuing... > Malformed response to offset query, qOffs > ets > (gdb) > > > Best regards, > > Elvis Dowson > > > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
