This patch makes it possible to select sw or hw (different layout options)
ecc scheme supported by omap nand driver. And hw ecc layout selected for
sdp and zoom boards, by default.
Signed-off-by: Sukumar Ghorai <s-ghorai@xxxxxx>
Signed-off-by: Vimal Singh <vimalsingh@xxxxxx>
---
arch/arm/mach-omap2/board-flash.c | 3 ++-
arch/arm/plat-omap/include/plat/nand.h | 6 ++++++
drivers/mtd/nand/omap2.c | 29 +++++++++++++----------------
3 files changed, 21 insertions(+), 17 deletions(-)
diff --git a/arch/arm/mach-omap2/board-flash.c b/arch/arm/mach-omap2/board-flash.c
index 4871d71..5f74c8f 100644
--- a/arch/arm/mach-omap2/board-flash.c
+++ b/arch/arm/mach-omap2/board-flash.c
@@ -144,7 +144,8 @@ __init board_nand_init(struct mtd_partition *nand_parts, u8 nr_parts, u8 cs)
{
board_nand_data.cs = cs;
board_nand_data.parts = nand_parts;
- board_nand_data.nr_parts = nr_parts;
+ board_nand_data.nr_parts = nr_parts;
+ board_nand_data.ecc_opt = OMAP_ECC_HAMMING_CODE_DIFF_LAYOUT;
gpmc_nand_init(&board_nand_data);
}
diff --git a/arch/arm/plat-omap/include/plat/nand.h b/arch/arm/plat-omap/include/plat/nand.h
index 5e69463..2e026e4 100644
--- a/arch/arm/plat-omap/include/plat/nand.h
+++ b/arch/arm/plat-omap/include/plat/nand.h
@@ -23,6 +23,12 @@ struct omap_nand_platform_data {
int gpmc_irq;
unsigned long phys_base;
int devsize;
+ enum {
+ OMAP_ECC_HAMMING_CODE_DIFF_LAYOUT = 0,
+ /* 1-bit s/w ecc and layout different from romcode */
+ OMAP_ECC_HAMMING_CODE_HW,/* 1-bit ecc, romcode layout */
+ OMAP_ECC_HAMMING_CODE_SW,/* 1-bit ecc, romcode layout */
+ } ecc_opt;
};
/* minimum size for IO mapping */
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index d457b9b..dbbd699 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -7,7 +7,6 @@
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-#define CONFIG_MTD_NAND_OMAP_HWECC
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
@@ -658,8 +657,6 @@ static int omap_verify_buf(struct mtd_info *mtd, const u_char * buf, int len)
return 0;
}
-#ifdef CONFIG_MTD_NAND_OMAP_HWECC
-
/**
* gen_true_ecc - This function will generate true ECC value
* @ecc_buf: buffer to store ecc code
@@ -879,8 +876,6 @@ static void omap_enable_hwecc(struct mtd_info *mtd, int mode)
gpmc_enable_hwecc(info->gpmc_cs, mode, dev_width, info->nand.ecc.size);
}
-#endif
-
/**
* omap_wait - wait until the command is done
* @mtd: MTD device structure
@@ -1059,17 +1054,19 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
}
info->nand.verify_buf = omap_verify_buf;
-#ifdef CONFIG_MTD_NAND_OMAP_HWECC
- info->nand.ecc.bytes = 3;
- info->nand.ecc.size = 512;
- info->nand.ecc.calculate = omap_calculate_ecc;
- info->nand.ecc.hwctl = omap_enable_hwecc;
- info->nand.ecc.correct = omap_correct_data;
- info->nand.ecc.mode = NAND_ECC_HW;
-
-#else
- info->nand.ecc.mode = NAND_ECC_SOFT;
-#endif
+ /* selsect the ecc type */
+ if ((pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_DIFF_LAYOUT) ||
+ (pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_HW)) {
+ info->nand.ecc.bytes = 3;
+ info->nand.ecc.size = 512;
+ info->nand.ecc.calculate = omap_calculate_ecc;
+ info->nand.ecc.hwctl = omap_enable_hwecc;
+ info->nand.ecc.correct = omap_correct_data;
+ info->nand.ecc.mode = NAND_ECC_HW;
+
+ } else if (pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_SW) {
+ info->nand.ecc.mode = NAND_ECC_SOFT;
+ }
/* DIP switches on some boards change between 8 and 16 bit
* bus widths for flash. Try the other width if the first try fails.
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
