> -----Original Message----- > From: Kevin Hilman [mailto:khilman@xxxxxxxxxxxxxxxxxxx] > Sent: Tuesday, September 14, 2010 10:28 PM > To: Basak, Partha > Cc: linux-omap@xxxxxxxxxxxxxxx; Varadarajan, Charulatha; Tero Kristo > Subject: Re: [PATCH 2/2] OMAP2+: GPIO: move late PM out of > interrupts-disabled idle path > > "Basak, Partha" <p-basak2@xxxxxx> writes: > > >> From: Kevin Hilman <khilman@xxxxxx> > >> > >> Currently, we wait until late in the idle path where interrupts are > >> disabled to do runtime-PM-like management for certain special-case > >> devices like GPIO. > >> > >> As a prerequiste to moving GPIO to the new runtime PM > framework, move > >> this runtime-PM-like code out of the late idle path into new device > >> idle and resume functions that can be called before interrupts are > >> disabled by CPUidle and/or suspend. > >> > >> In addition, move all the GPIO-specific logic into the GPIO core > >> instead of keeping GPIO-specific knowledge of power-states, context > >> saving etc. in the PM core. > >> > >> Also, call the new device-idle and -resume methods from CPUidle and > >> static suspend path. > >> > >> Signed-off-by: Kevin Hilman <khilman@xxxxxx> > >> --- > >> arch/arm/mach-omap2/cpuidle34xx.c | 4 ++ > >> arch/arm/mach-omap2/pm.h | 2 + > >> arch/arm/mach-omap2/pm24xx.c | 2 +- > >> arch/arm/mach-omap2/pm34xx.c | 38 > +++++++++------------ > >> arch/arm/plat-omap/gpio.c | 57 > >> ++++++++++++++++++++++++-------- > >> arch/arm/plat-omap/include/plat/gpio.h | 4 +-- > >> 6 files changed, 67 insertions(+), 40 deletions(-) > >> > >> diff --git a/arch/arm/mach-omap2/cpuidle34xx.c > >> b/arch/arm/mach-omap2/cpuidle34xx.c > >> index 0923b82..681d823 100644 > >> --- a/arch/arm/mach-omap2/cpuidle34xx.c > >> +++ b/arch/arm/mach-omap2/cpuidle34xx.c > >> @@ -274,9 +274,13 @@ static int omap3_enter_idle_bm(struct > >> cpuidle_device *dev, > >> pwrdm_set_next_pwrst(per_pd, per_next_state); > >> > >> select_state: > >> + omap3_device_idle(); > >> + > >> dev->last_state = new_state; > >> ret = omap3_enter_idle(dev, new_state); > >> > >> + omap3_device_resume(); > >> + > > In the generic cpu_idle() in process.c, interrupts are > already disabled > > before control comes to cpuidle_idle_call() via pm_idle() > > local_irq_disable(); > > if (hlt_counter) { > > local_irq_enable(); > > cpu_relax(); > > } else { > > stop_critical_timings(); > > pm_idle(); > > start_critical_timings(); > > /* > > * This will eventually be > removed - pm_idle > > * functions should always > return with IRQs > > * enabled. > > */ > > WARN_ON(irqs_disabled()); > > local_irq_enable(); > > } > > > > omap3_enter_idle_bm() will be called from inside > cpuidle_idle_call() > > via target_state->enter(dev, target_state). > > So, interrupts are already disabled here. > > > > Am I missing something? > > You're right. > > I knew this was the case for !CPUIDLE setup, but had thought (without > testing) that the CPUidle core had re-enabled interrupts during the > governor selection process etc. > > While I investigate ways to manage this in CPUidle, the > following should > be fine for now to include with $SUBJECT patch. > > Kevin > > diff --git a/arch/arm/mach-omap2/cpuidle34xx.c > b/arch/arm/mach-omap2/cpuidle34xx.c > index 681d823..c5cb9d0 100644 > --- a/arch/arm/mach-omap2/cpuidle34xx.c > +++ b/arch/arm/mach-omap2/cpuidle34xx.c > @@ -245,6 +245,14 @@ static int omap3_enter_idle_bm(struct > cpuidle_device *dev, > goto select_state; > } > > + /* > + * Enable IRQs during the device activity checking and > idle management. > + * IRQs are later (re)disabled when entering the actual > idle function. > + * Device idle management that is using runtime PM needs to have > + * interrupts enabled when calling into the runtime PM core. > + */ > + local_irq_enable(); > + > cx = cpuidle_get_statedata(state); > core_next_state = cx->core_state; > OK. We will base on top of this patch. > k > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html