Hi, I have am3517 based board and Libertas sdio (4 wires) wifi connected directly (no transceiver / level shifter) on mmc2 (which is named mmc1 in s/w). am3517 is configured (h/w) for 3.3V and so is Libertas wifi. dmesg | grep mmc1 shows: --------------cut------------------ mux: Setting signal sdmmc1_clk.sdmmc1_clk 0x0000 -> 0x0118 mux: Setting signal sdmmc1_cmd.sdmmc1_cmd 0x0000 -> 0x0118 mux: Setting signal sdmmc1_dat0.sdmmc1_dat0 0x0100 -> 0x0118 mux: Setting signal sdmmc1_dat1.sdmmc1_dat1 0x0100 -> 0x0118 mux: Setting signal sdmmc1_dat2.sdmmc1_dat2 0x0100 -> 0x0118 mux: Setting signal sdmmc1_dat3.sdmmc1_dat3 0x0100 -> 0x0118 mmc1: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0 mmc1: clock 0Hz busmode 1 powermode 1 cs 0 Vdd 20 width 0 timing 0 mmc1: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 20 width 0 timing 0 mmc1: starting CMD52 arg 00000c00 flags 00000195 mmci-omap-hs mmci-omap-hs.1: mmc1: CMD52, argument 0x00000c00 mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000 mmc1: starting CMD52 arg 80000c08 flags 00000195 mmci-omap-hs mmci-omap-hs.1: mmc1: CMD52, argument 0x80000c08 mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000 mmc1: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd 20 width 0 timing 0 mmc1: starting CMD0 arg 00000000 flags 000000c0 mmci-omap-hs mmci-omap-hs.1: mmc1: CMD0, argument 0x00000000 mmc1: req done (CMD0): 0: 00000000 00000000 00000000 00000000 mmc1: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 20 width 0 timing 0 mmc1: starting CMD8 arg 000001aa flags 000002f5 mmci-omap-hs mmci-omap-hs.1: mmc1: CMD8, argument 0x000001aa mmc1: req done (CMD8): -110: 00000000 00000000 00000000 00000000 mmc1: starting CMD5 arg 00000000 flags 000002e1 mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000 mmc1: req failed (CMD5): -110, retrying... mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000 mmc1: req failed (CMD5): -110, retrying... mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000 mmc1: req failed (CMD5): -110, retrying... mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000 mmc1: req done (CMD5): -110: 00000000 00000000 00000000 00000000 mmc1: starting CMD55 arg 00000000 flags 000000f5 mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000 mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000 mmc1: starting CMD55 arg 00000000 flags 000000f5 mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000 mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000 mmc1: starting CMD55 arg 00000000 flags 000000f5 mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000 mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000 mmc1: starting CMD55 arg 00000000 flags 000000f5 mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000 mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000 mmc1: starting CMD1 arg 00000000 flags 000000e1 mmci-omap-hs mmci-omap-hs.1: mmc1: CMD1, argument 0x00000000 mmc1: req done (CMD1): -110: 00000000 00000000 00000000 00000000 mmc1: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0 -------------------cut--------------------- Libertas is powered up and gets reseted properly. On the oscilloscope, I see some communication going on the CMD line and stops after some time. am3517 PSP from TI, does not even registers/enables the wifi combo found on am3517evm. Have anybody got the mmc2 working on am3517? May be with transceiver? Any help will be appreciated. Thanks -- Regards, Igor. -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
