ARM: OMAP3LOGIC: Adding SDMMC support
Add low-level initialization for hsmmc controller for
LogicPD's OMAP 3530 LV SOM and OMAP 35x Torpedo board.
Signed-off-by: Jacob Tanenbaum <Jacob.Tanenbaum@xxxxxxxxxxx>
---
arch/arm/mach-omap2/board-omap3logic.c | 69 +++++++++++++++++++++++++++++++-
1 files changed, 68 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3logic.c b/arch/arm/mach-omap2/board-omap3logic.c
index fe5db85..13e0b16 100644
--- a/arch/arm/mach-omap2/board-omap3logic.c
+++ b/arch/arm/mach-omap2/board-omap3logic.c
@@ -33,13 +33,18 @@
#include <asm/mach/map.h>
#include "mux.h"
-
+#include "hsmmc.h"
#include <plat/mux.h>
#include <plat/board.h>
#include <plat/common.h>
#include <plat/gpmc.h>
#include <plat/timer-gp.h>
+#define OMAP3530_LV_SOM_MMC_GPIO_CD 110
+#define OMAP3530_LV_SOM_MMC_GPIO_WP 126
+#define OMAP3_TORPEDO_MMC_GPIO_CD 127
+#define OMAP3_TORPEDO_MMC_GPIO_WP (-EINVAL)
+
/* Micron MT46H32M32LF-6 */
/* FIXME: borrowed from sdram-micron-mt46h32m32lf-6.h because on LogicPD
* boards we can't use the default values -- why? I suspect the reason
@@ -80,6 +85,28 @@ static struct omap_sdrc_params mt46h32m32lf6_sdrc_params[] = {
},
};
+
+static struct regulator_consumer_supply omap3logic_vmmc1_supply = {
+ .supply = "vmmc",
+};
+
+/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
+static struct regulator_init_data omap3logic_vmmc1 = {
+ .constraints = {
+ .name = "VMMC1",
+ .min_uV = 1850000,
+ .max_uV = 3150000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &omap3logic_vmmc1_supply,
+};
+
+
static int omap3logic_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
@@ -121,6 +148,44 @@ static int __init omap3logic_i2c_init(void)
return 0;
}
+
+static struct omap2_hsmmc_info __initdata board_mmc_info[] = {
+ {
+ .name = "external",
+ .mmc = 1,
+ .wires = 4,
+ .gpio_cd = -EINVAL,
+ .gpio_wp = -EINVAL,
+ },
+ {} /* Terminator */
+};
+
+static void __init board_mmc_init(void)
+{
+ /* OMAP3530 LV SOM board */
+ if (machine_is_omap3530_lv_som()) {
+ board_mmc_info[0].gpio_cd = OMAP3530_LV_SOM_MMC_GPIO_CD;
+ board_mmc_info[0].gpio_wp = OMAP3530_LV_SOM_MMC_GPIO_WP;
+ omap_mux_init_signal("gpio_110", OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("gpio_126", OMAP_PIN_OUTPUT);
+
+
+ /* OMAP3 Torpedo board */
+ } else if (machine_is_omap3_torpedo()) {
+ board_mmc_info[0].gpio_cd = OMAP3_TORPEDO_MMC_GPIO_CD;
+ omap_mux_init_signal("gpio_127", OMAP_PIN_OUTPUT);
+ /* unsupported board */
+ } else {
+ printk(KERN_ERR "%s(): unknown machine type\n", __func__);
+ return;
+ }
+
+ omap2_hsmmc_init(board_mmc_info);
+ /* link regulators to MMC adapters */
+ omap3logic_vmmc1_supply.dev = board_mmc_info[0].dev;
+}
+
+
static struct omap_board_config_kernel omap3logic_config[] __initdata = {
};
@@ -164,6 +229,7 @@ static void __init omap3logic_map_io(void)
MACHINE_START(OMAP3_TORPEDO, "Logic OMAP3 Torpedo board")
/* Maintainer: Peter Barada <peterb@xxxxxxxxxxx> */
+
.phys_io = 0x48000000,
.io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
.boot_params = 0x80000100,
@@ -175,6 +241,7 @@ MACHINE_END
MACHINE_START(OMAP3530_LV_SOM, "OMAP Logic 3530 LV SOM board")
/* Maintainer: Peter Barada <peterb@xxxxxxxxxxx> */
+
.phys_io = 0x48000000,
.io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
.boot_params = 0x80000100,
--
1.6.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
