AM35x has musb interface (version 1.8) and uses CPPI41 DMA engine.
It supports upto 500mA of power in host mode.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@xxxxxx>
---
Changes from v1:
- Added PHY clock and OTGMODE settings in board files
arch/arm/mach-omap2/board-am3517evm.c | 42 +++++++++++++++++++++++++++++++++
arch/arm/mach-omap2/usb-musb.c | 4 +++
arch/arm/plat-omap/include/plat/usb.h | 21 ++++++++++++++++
3 files changed, 67 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index 837f294..c66ac72 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -32,6 +32,7 @@
#include <plat/common.h>
#include <plat/usb.h>
#include <plat/display.h>
+#include <plat/control.h>
#include "mux.h"
@@ -278,6 +279,12 @@ static void __init am3517_evm_init_irq(void)
omap_gpio_init();
}
+static struct omap_musb_board_data musb_board_data = {
+ .interface_type = MUSB_INTERFACE_ULPI,
+ .mode = MUSB_OTG,
+ .power = 500,
+};
+
static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
#if defined(CONFIG_PANEL_SHARP_LQ043T1DG01) || \
@@ -296,12 +303,45 @@ static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
+ /* USB OTG DRVVBUS offset = 0x212 */
+ OMAP3_MUX(SAD2D_MCAD23, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#else
#define board_mux NULL
#endif
+static __init void am3517_evm_musb_init(void)
+{
+ u32 devconf2;
+
+ /*
+ * Set up USB clock/mode in the DEVCONF2 register.
+ */
+ devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
+
+ /* USB2.0 PHY reference clock is 13 MHz */
+ devconf2 &= ~CONF2_REFFREQ;
+ devconf2 |= CONF2_REFFREQ_13MHZ;
+
+ /*
+ * We have to override VBUS/ID signals when MUSB is configured into the
+ * host-only mode -- ID pin will float if no cable is connected, so the
+ * controller won't be able to drive VBUS thinking that it's a B-device.
+ * Otherwise, we want to use the OTG mode and enable VBUS comparators.
+ */
+ devconf2 &= ~CONF2_OTGMODE;
+#ifdef CONFIG_USB_MUSB_HOST
+ devconf2 |= CONF2_FORCE_HOST;
+#else
+ devconf2 |= CONF2_SESENDEN | CONF2_VBDTCTEN;
+#endif
+
+ omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
+
+ usb_musb_init(&musb_board_data);
+}
+
static void __init am3517_evm_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
@@ -323,6 +363,8 @@ static void __init am3517_evm_init(void)
i2c_register_board_info(1, am3517evm_i2c_boardinfo,
ARRAY_SIZE(am3517evm_i2c_boardinfo));
+ /* MUSB */
+ am3517_evm_musb_init();
}
static void __init am3517_evm_map_io(void)
diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c
index 6d41fa7..710020d 100644
--- a/arch/arm/mach-omap2/usb-musb.c
+++ b/arch/arm/mach-omap2/usb-musb.c
@@ -28,6 +28,7 @@
#include <mach/hardware.h>
#include <mach/irqs.h>
+#include <mach/am35xx.h>
#include <plat/mux.h>
#include <plat/usb.h>
@@ -90,6 +91,9 @@ void __init usb_musb_init(struct omap_musb_board_data *board_data)
{
if (cpu_is_omap243x()) {
musb_resources[0].start = OMAP243X_HS_BASE;
+ } else if (cpu_is_omap3517()) {
+ musb_resources[0].start = AM35XX_IPSS_USBOTGSS_BASE;
+ musb_resources[1].start = INT_35XX_USBOTG_IRQ;
} else if (cpu_is_omap34xx()) {
musb_resources[0].start = OMAP34XX_HSUSB_OTG_BASE;
} else if (cpu_is_omap44xx()) {
diff --git a/arch/arm/plat-omap/include/plat/usb.h b/arch/arm/plat-omap/include/plat/usb.h
index 876ca8d..c0e416c 100644
--- a/arch/arm/plat-omap/include/plat/usb.h
+++ b/arch/arm/plat-omap/include/plat/usb.h
@@ -167,5 +167,26 @@ void omap_usb_init(struct omap_usb_config *pdata);
# define USBT2TLL5PI (1 << 17)
# define USB0PUENACTLOI (1 << 16)
# define USBSTANDBYCTRL (1 << 15)
+/* AM3517 */
+/* USB 2.0 PHY Control */
+#define CONF2_PHY_GPIOMODE (1 << 23)
+#define CONF2_OTGMODE (3 << 14)
+#define CONF2_NO_OVERRIDE (0 << 14)
+#define CONF2_FORCE_HOST (1 << 14)
+#define CONF2_FORCE_DEVICE (2 << 14)
+#define CONF2_FORCE_HOST_VBUS_LOW (3 << 14)
+#define CONF2_SESENDEN (1 << 13)
+#define CONF2_VBDTCTEN (1 << 12)
+#define CONF2_REFFREQ_24MHZ (2 << 8)
+#define CONF2_REFFREQ_26MHZ (7 << 8)
+#define CONF2_REFFREQ_13MHZ (6 << 8)
+#define CONF2_REFFREQ (0xf << 8)
+#define CONF2_PHYCLKGD (1 << 7)
+#define CONF2_VBUSSENSE (1 << 6)
+#define CONF2_PHY_PLLON (1 << 5)
+#define CONF2_RESET (1 << 4)
+#define CONF2_PHYPWRDN (1 << 3)
+#define CONF2_OTGPWRDN (1 << 2)
+#define CONF2_DATPOL (1 << 1)
#endif /* __ASM_ARCH_OMAP_USB_H */
--
1.6.2.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
