Hello.
Ajay Kumar Gupta wrote:
AM35x has musb interface (version 1.8) and uses CPPI41 DMA engine.
It supports upto 500mA of power in host mode.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@xxxxxx>
---
Created against latest l-o master branch and below patches.
[1] AM35xx: Add clock support for new modules on AM35xx
[2] OMAP2/3 clock: Extend find_idlest() to pass back idle
[3] musb: fix power field to hold all possible values
[4] musb: Add extvbus in musb_board_data
I am posting musb driver layer platform file seperately to linux-usb list.
arch/arm/mach-omap2/board-am3517evm.c | 10 ++++++++
arch/arm/mach-omap2/usb-musb.c | 4 +++
arch/arm/plat-omap/include/plat/usb.h | 38 +++++++++++++++++++++++++++++++++
3 files changed, 52 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index aee0a02..805c7ab 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -273,6 +273,12 @@ static void __init am3517_evm_init_irq(void)
omap_gpio_init();
}
+static struct omap_musb_board_data musb_board_data = {
+ .interface_type = MUSB_INTERFACE_ULPI,
+ .mode = MUSB_OTG,
+ .power = 500,
+};
+
static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
@@ -286,6 +292,8 @@ static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
+ /* USB OTG DRVVBUS offset = 0x212 */
+ OMAP3_MUX(CHASSIS_DMAREQ3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#else
@@ -313,6 +321,8 @@ static void __init am3517_evm_init(void)
i2c_register_board_info(1, am3517evm_i2c_boardinfo,
ARRAY_SIZE(am3517evm_i2c_boardinfo));
+ /* MUSB */
+ usb_musb_init(&musb_board_data);
}
static void __init am3517_evm_map_io(void)
diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c
index 17726ac..1b08cff 100644
--- a/arch/arm/mach-omap2/usb-musb.c
+++ b/arch/arm/mach-omap2/usb-musb.c
@@ -28,6 +28,7 @@
#include <mach/hardware.h>
#include <mach/irqs.h>
+#include <mach/am35xx.h>
#include <plat/mux.h>
#include <plat/usb.h>
@@ -89,6 +90,9 @@ void __init usb_musb_init(struct omap_musb_board_data *board_data)
{
if (cpu_is_omap243x()) {
musb_resources[0].start = OMAP243X_HS_BASE;
+ } else if (cpu_is_omap3517()) {
+ musb_resources[0].start = AM35XX_IPSS_USBOTGSS_BASE;
+ musb_resources[1].start = INT_35XX_USBOTG_IRQ;
} else if (cpu_is_omap34xx()) {
musb_resources[0].start = OMAP34XX_HSUSB_OTG_BASE;
} else if (cpu_is_omap44xx()) {
diff --git a/arch/arm/plat-omap/include/plat/usb.h b/arch/arm/plat-omap/include/plat/usb.h
index d82bf77..2df6c70 100644
--- a/arch/arm/plat-omap/include/plat/usb.h
+++ b/arch/arm/plat-omap/include/plat/usb.h
@@ -168,5 +168,43 @@ void omap_usb_init(struct omap_usb_config *pdata);
# define USBT2TLL5PI (1 << 17)
# define USB0PUENACTLOI (1 << 16)
# define USBSTANDBYCTRL (1 << 15)
+/* AM3517 */
+/* USB 2.0 OTG module registers */
+#define USB_REVISION_REG 0x00
+#define USB_CTRL_REG 0x04
+#define USB_STAT_REG 0x08
+#define USB_EMULATION_REG 0x0c
+/* 0x10 Reserved */
Wait... so the mode register isn't supported? Does AM35x support any
accelerated modes?
+#define USB_AUTOREQ_REG 0x14
+#define USB_SRP_FIX_TIME_REG 0x18
+#define USB_TEARDOWN_REG 0x1c
+#define EP_INTR_SRC_REG 0x20
+#define EP_INTR_SRC_SET_REG 0x24
+#define EP_INTR_SRC_CLEAR_REG 0x28
+#define EP_INTR_MASK_REG 0x2c
+#define EP_INTR_MASK_SET_REG 0x30
+#define EP_INTR_MASK_CLEAR_REG 0x34
+#define EP_INTR_SRC_MASKED_REG 0x38
+#define CORE_INTR_SRC_REG 0x40
+#define CORE_INTR_SRC_SET_REG 0x44
+#define CORE_INTR_SRC_CLEAR_REG 0x48
+#define CORE_INTR_MASK_REG 0x4c
+#define CORE_INTR_MASK_SET_REG 0x50
+#define CORE_INTR_MASK_CLEAR_REG 0x54
+#define CORE_INTR_SRC_MASKED_REG 0x58
+/* 0x5c Reserved */
+#define USB_END_OF_INTR_REG 0x60
Hm, I don't see the generic RNDIS EP size registers also. So, generic
RNDIS mode isn't supported? Then cppi41_dma.c won't work with this
chip... :-/
WBR, Sergei
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html