> -----Original Message----- > From: G, Manjunath Kondaiah > Sent: Wednesday, March 03, 2010 12:38 AM > To: G, Manjunath Kondaiah; Aguirre, Sergio; linux-omap@xxxxxxxxxxxxxxx > Cc: Tony Lindgren; Shilimkar, Santosh; Raja, Govindraj > Subject: RE: [PATCH] OMAP: Zoom3: Fix Zoom3 booting issue > > > > > > -----Original Message----- > > From: G, Manjunath Kondaiah > > Sent: Wednesday, March 03, 2010 11:31 AM > > To: Aguirre, Sergio; linux-omap@xxxxxxxxxxxxxxx > > Cc: Tony Lindgren; Shilimkar, Santosh; Raja, Govindraj > > Subject: RE: [PATCH] OMAP: Zoom3: Fix Zoom3 booting issue > > > > Sergio, > > > > > -----Original Message----- > > > From: Aguirre, Sergio > > > Sent: Tuesday, March 02, 2010 9:41 PM > > > To: G, Manjunath Kondaiah; linux-omap@xxxxxxxxxxxxxxx > > > Cc: G, Manjunath Kondaiah; Tony Lindgren; Shilimkar, Santosh; > > > Raja, Govindraj > > > Subject: RE: [PATCH] OMAP: Zoom3: Fix Zoom3 booting issue > > > > > > Manju, > > > > > > > -----Original Message----- > > > > From: linux-omap-owner@xxxxxxxxxxxxxxx [mailto:linux-omap- > > > > owner@xxxxxxxxxxxxxxx] On Behalf Of Manjunatha GK > > > > Sent: Tuesday, March 02, 2010 7:36 AM > > > > To: linux-omap@xxxxxxxxxxxxxxx > > > > Cc: G, Manjunath Kondaiah; Tony Lindgren; Shilimkar, > > Santosh; Raja, > > > > Govindraj > > > > Subject: [PATCH] OMAP: Zoom3: Fix Zoom3 booting issue > > > > > > > > The commit id "5550bc33a1a9002976022cc794fe8c52ad9a0021" > > seems to be > > > > broken > > > > zoom3 boot which adds support for UART4 on OMAP4 and OMAP3630. > > > > > > > > But, it looks like OMAP3630 UART4 interface and functional > > > clock nodes > > > > needs > > > > to be added for omap3630. Thus limiting no. of UART's for > > > 3630 to 3 to > > > > prevent > > > > boot up issues until clock nodes are added for UART4 on OMAP3630. > > > > > > I already tried a similar patch here: > > > > > > http://patchwork.kernel.org/patch/81692/ > > > > > > But as it is really not solving anything, and Tony rejected > > > it, I started working on the needed bits to get UART4 > > > enabled, therefore I have came up with this patch series: > > > > > > - [RFC v3][PATCH 0/6] OMAP3630: UART4 startup (+ new bugfix!) [1] > > > > > > Also, I'm working in my spare time on a cleanup proposal [2], > > > which I'll repost today, given some comments from Kevin. > > > > > > So, if you want to boot, take series [1] and [2], and then > > > you should be able to boot with ttyS0. > > > > Sergio, did you test this combination on zoom3? It seems to > > be not working > > on zoom3 with ttyS0 and also with ttyS3. > > > > Where as, reducing number of uarts(for 3630) to 3 seems to > > working fine for > > ttyS3 on zoom3. > > To update further, it seems to be working on zoom3 with ttyS0 > with following combination of patches: > > 1. > [RFC,part2,v1,4/4] omap3: zoom 2/3: Change debugboard serial port id > [RFC,part2,v1,3/4] omap3: 3630sdp: Explicitly enable all UARTs > [RFC,part2,v1,2/4] omap3: zoom2/3 / 3630sdp: Don't init always all uarts > [RFC,part2,v1,1/4] omap2/3/4: serial: rename omap_serial_init > > 2. > [RESEND,PATCH/RFC] OMAP2: serial.c: Fix number of uarts in early_init > > 3. > [RFC,v3,6/6] omap3: serial: Fix uart4 handling for 3630 > [RFC,v3,5/6] OMAP3: PRCM: Consider UART4 for 3630 chip in prcm_setup_regs > [RFC,v3,4/6] OMAP clock: Add uart4_ick/fck definitions for 3630 > [RFC,v3,3/6] ARM: OMAP3630: PRCM: Add UART4 control bits > [RFC,v3,2/6] omap2/3/4: serial: Remove condition for getting uart4_phys > [RFC,v3,1/6] OMAP3: serial: Check for zero-based physical addr Yeah, that should be the total patchlist applied. I'm assuming you're applying from bottom to top order in your list above... Regards, Sergio > > -Manjunath -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
