Hi, The mux configuration is set at u-boot level and this works with kernel 2.6.28 so I suppose the mux configuration is setup correctly. Looking at driver I see new data in twl4030_hsmmc_info struct. Please, can you explain a bit the transceiver, ocr_mask and ext_clock ? Just for information, on IGEP v2 the MMC2 should be at 1.8V and don't use twl4030 regulator. Thanks a lot, Enric 2010/1/5 Madhusudhan <madhu.cr@xxxxxx>: > Hi Enric, > > You see from the log there is a timeout on CMD5. This could happen because > of multiple reasons. One of them is muxing of CMD/CLK lines. Or it could be > due to negotiation of voltage. > > I would look at these things first. > > Regards, > Madhu > > ________________________________________ > From: Enric Balletbò i Serra [mailto:eballetbo@xxxxxxxxx] > Sent: Tuesday, January 05, 2010 10:44 AM > To: linux-omap@xxxxxxxxxxxxxxx; madhu.cr@xxxxxx > Subject: Question about omap_hsmmc driver > > Hi all, > > I'm having problems trying to run the SDIO WLAN module on my IGEP v2 board > using the latest omap kernel (2.6.33-rc2). The SDIO WLAN module is connected > to the MMC2 using 4 wires. With an older kernel ( 2.6.28 ) works fine but > the same configuration with 2.6.33-rc2 do not detect the SDIO card. > > > Any idea to solve the problem ? There is a substantial modification in this > driver. Any help will be appreciated. I attached the log. > > Thanks in advance, > Enric > > > [ 24.521484] mmci-omap-hs mmci-omap-hs.1: DISABLED -> ENABLED > [ 24.522003] mmc1: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 > timing 0 > [ 24.522033] mmci-omap-hs mmci-omap-hs.1: ENABLED -> DISABLED > [ 24.522308] mmci-omap-hs mmci-omap-hs.1: DISABLED -> ENABLED > [ 24.522338] mmc1: clock 0Hz busmode 1 powermode 1 cs 0 Vdd 65535 width 0 > timing 0 > [ 24.545104] mmc1: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 65535 > width 0 timing 0 > [ 24.568298] mmc1: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd 65535 > width 0 timing 0 > [ 24.569335] mmc1: starting CMD0 arg 00000000 flags 000000c0 > [ 24.569366] mmci-omap-hs mmci-omap-hs.1: mmc1: CMD0, argument 0x00000000 > [ 24.569519] mmci-omap-hs mmci-omap-hs.1: IRQ Status is 1 > [ 24.569549] mmc1: req done (CMD0): 0: 00000000 00000000 00000000 00000000 > [ 24.572540] mmc1: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 65535 > width 0 timing 0 > [ 24.573547] mmc1: starting CMD8 arg 000000aa flags 000002f5 > [ 24.573577] mmci-omap-hs mmci-omap-hs.1: mmc1: CMD8, argument 0x000000aa > [ 24.573913] mmci-omap-hs mmci-omap-hs.1: IRQ Status is 18000 > [ 24.573913] mmci-omap-hs mmci-omap-hs.1: MMC IRQ 0x18000 : ERRI CTO > [ 24.573944] mmc1: req done (CMD8): -110: 00000000 00000000 00000000 > 00000000 > [ 24.575744] mmc1: starting CMD5 arg 00000000 flags 000002e1 > [ 24.575775] mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000 > [ 24.576110] mmci-omap-hs mmci-omap-hs.1: IRQ Status is 18000 > [ 24.576141] mmci-omap-hs mmci-omap-hs.1: MMC IRQ 0x18000 : ERRI CTO > [ 24.576171] mmc1: req failed (CMD5): -110, retrying... > [ 24.576171] mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000 > [ 24.576507] mmci-omap-hs mmci-omap-hs.1: IRQ Status is 18000 > [ 24.576538] mmci-omap-hs mmci-omap-hs.1: MMC IRQ 0x18000 : ERRI CTO > [ 24.576568] mmc1: req failed (CMD5): -110, retrying... > [ 24.576568] mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000 > [ 24.576904] mmci-omap-hs mmci-omap-hs.1: IRQ Status is 18000 > [ 24.576934] mmci-omap-hs mmci-omap-hs.1: MMC IRQ 0x18000 : ERRI CTO > [ 24.576934] mmc1: req failed (CMD5): -110, retrying... > [ 24.576965] mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000 > [ 24.577301] mmci-omap-hs mmci-omap-hs.1: IRQ Status is 18000 > [ 24.577331] mmci-omap-hs mmci-omap-hs.1: MMC IRQ 0x18000 : ERRI CTO > [ 24.577331] mmc1: req done (CMD5): -110: 00000000 00000000 00000000 > 00000000 > [ 24.578247] mmc1: starting CMD55 arg 00000000 flags 000000f5 > [ 24.578247] mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000 > [ 24.578582] mmci-omap-hs mmci-omap-hs.1: IRQ Status is 18000 > [ 24.578613] mmci-omap-hs mmci-omap-hs.1: MMC IRQ 0x18000 : ERRI CTO > [ 24.578643] mmc1: req done (CMD55): -110: 00000000 00000000 00000000 > 00000000 > [ 24.580444] mmc1: starting CMD55 arg 00000000 flags 000000f5 > [ 24.580474] mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000 > [ 24.580810] mmci-omap-hs mmci-omap-hs.1: IRQ Status is 18000 > [ 24.580810] mmci-omap-hs mmci-omap-hs.1: MMC IRQ 0x18000 : ERRI CTO > [ 24.580841] mmc1: req done (CMD55): -110: 00000000 00000000 00000000 > 00000000 > [ 24.582641] mmc1: starting CMD55 arg 00000000 flags 000000f5 > [ 24.582672] mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000 > [ 24.583007] mmci-omap-hs mmci-omap-hs.1: IRQ Status is 18000 > [ 24.583007] mmci-omap-hs mmci-omap-hs.1: MMC IRQ 0x18000 : ERRI CTO > [ 24.583038] mmc1: req done (CMD55): -110: 00000000 00000000 00000000 > 00000000 > [ 24.584899] mmc1: starting CMD55 arg 00000000 flags 000000f5 > [ 24.584899] mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000 > [ 24.585235] mmci-omap-hs mmci-omap-hs.1: IRQ Status is 18000 > [ 24.585266] mmci-omap-hs mmci-omap-hs.1: MMC IRQ 0x18000 : ERRI CTO > [ 24.585296] mmc1: req done (CMD55): -110: 00000000 00000000 00000000 > 00000000 > [ 24.587097] mmc1: starting CMD1 arg 00000000 flags 000000e1 > [ 24.587097] mmci-omap-hs mmci-omap-hs.1: mmc1: CMD1, argument 0x00000000 > [ 24.587432] mmci-omap-hs mmci-omap-hs.1: IRQ Status is 18000 > [ 24.587463] mmci-omap-hs mmci-omap-hs.1: MMC IRQ 0x18000 : ERRI CTO > [ 24.587493] mmc1: req done (CMD1): -110: 00000000 00000000 00000000 > 00000000 > [ 24.589294] mmc1: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 > timing 0 > [ 24.623962] mmci-omap-hs mmci-omap-hs.1: ENABLED -> DISABLED > > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
