"Reddy, Teerth" <teerth@xxxxxx> writes:
> Reposting the patch with proper format
>
> From: Teerth Reddy <teerth@xxxxxx>
>
> This patch sets the dpll3 clock stabilization delay during
> DVFS. The stabilization delay is calculated dynamically
> using the ARM performance counter.
> Currently 6us of SDRC stabilization value is used to get
> the correct delay.
Needs more thorough changelog describing the problem being solved.
First, some general comments/questions:
PMC code is ARM generic and already largely exists in other places
(oprofile for one.) So the use of the PMC will need to be generalized
as well as be shown not to interfere with other users (as raised
already by Jean Pihet.)
Couldn't you use a GPtimer for this?
> Signed-off-by: Romit Dasgupta <romit@xxxxxx>
> Signed-off-by: Teerth Reddy <teerth@xxxxxx>
> ---
> mach-omap2/clock34xx.c | 32 +++++++++++++---------------
> mach-omap2/sram34xx.S | 7 ++++++
> plat-omap/Makefile | 1
> plat-omap/include/plat/pmc.h | 9 ++++++++
> plat-omap/include/plat/sram.h | 6 +++++
> plat-omap/pmc.c | 47 ++++++++++++++++++++++++++++++++++++++++++
> plat-omap/sram.c | 23 ++++++++++++++++++++
> 7 files changed, 108 insertions(+), 17 deletions(-)
>
>
> diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c
> index da5bc1f..dd49938 100644
> --- a/arch/arm/mach-omap2/clock34xx.c
> +++ b/arch/arm/mach-omap2/clock34xx.c
> @@ -37,6 +37,8 @@
> #include <asm/div64.h>
> #include <asm/clkdev.h>
>
> +#include <plat/pmc.h>
> +
> #include <plat/sdrc.h>
> #include "clock.h"
> #include "prm.h"
> @@ -46,6 +48,8 @@
>
> static const struct clkops clkops_noncore_dpll_ops;
>
> +unsigned int delay_sram;
> +
static? The only users I see are in this file.
> static void omap3430es2_clk_ssi_find_idlest(struct clk *clk,
> void __iomem **idlest_reg,
> u8 *idlest_bit);
> @@ -333,14 +337,9 @@ static struct omap_clk omap34xx_clks[] = {
> /* Scale factor for fixed-point arith in omap3_core_dpll_m2_set_rate() */
> #define SDRC_MPURATE_SCALE 8
>
> -/* 2^SDRC_MPURATE_BASE_SHIFT: MPU MHz that SDRC_MPURATE_LOOPS is defined for */
> -#define SDRC_MPURATE_BASE_SHIFT 9
> -
> -/*
> - * SDRC_MPURATE_LOOPS: Number of MPU loops to execute at
> - * 2^MPURATE_BASE_SHIFT MHz for SDRC to stabilize
> - */
> -#define SDRC_MPURATE_LOOPS 96
> +/* SDRC_TIME_STABILIZE: Time for SDRC to stabilize in us */
> +/* hardcoded currently */
hardcoded currently why? "currently" makes it sound like there are
some other plans. Would be useful to comment on what those are.
> +#define SDRC_TIME_STABILIZE 6
>
> /*
> * DPLL5_FREQ_FOR_USBHOST: USBHOST and USBTLL are the only clocks
> @@ -870,16 +869,10 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
> unlock_dll = 1;
> }
>
> - /*
> - * XXX This only needs to be done when the CPU frequency changes
> - */
> + /* Calculate the number of MPU cycles to wait for SDRC to stabilize */
> +
> mpurate = arm_fck.rate / CYCLES_PER_MHZ;
> - c = (mpurate << SDRC_MPURATE_SCALE) >> SDRC_MPURATE_BASE_SHIFT;
> - c += 1; /* for safety */
> - c *= SDRC_MPURATE_LOOPS;
> - c >>= SDRC_MPURATE_SCALE;
> - if (c == 0)
> - c = 1;
> + c = ((SDRC_TIME_STABILIZE * mpurate) / (delay_sram * 2));
>
> pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate,
> validrate);
> @@ -1228,6 +1221,11 @@ int __init omap2_clk_init(void)
> vclk = clk_get(NULL, "virt_prcm_set");
> sclk = clk_get(NULL, "sys_ck");
> #endif
> +
> + /* Measure sram delay */
> + delay_sram = measure_sram_delay(10000)/(10000*2);
> + pr_debug("SRAM delay: %d\n", delay_sram);
> +
> return 0;
> }
>
> diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S
> index 82aa4a3..dc0ac72 100644
> --- a/arch/arm/mach-omap2/sram34xx.S
> +++ b/arch/arm/mach-omap2/sram34xx.S
> @@ -298,3 +298,10 @@ core_m2_mask_val:
> ENTRY(omap3_sram_configure_core_dpll_sz)
> .word . - omap3_sram_configure_core_dpll
>
> +ENTRY(__sram_wait_delay)
> + subs r0, r0, #1
> + bne __sram_wait_delay
> + bx lr
> +
> +ENTRY(__sram_wait_delay_sz)
> + .word . - __sram_wait_delay
> diff --git a/arch/arm/plat-omap/Makefile b/arch/arm/plat-omap/Makefile
> index 95f8413..aac43da 100644
> --- a/arch/arm/plat-omap/Makefile
> +++ b/arch/arm/plat-omap/Makefile
> @@ -15,6 +15,7 @@ obj-$(CONFIG_ARCH_OMAP16XX) += ocpi.o
> # omap_device support (OMAP2+ only at the moment)
> obj-$(CONFIG_ARCH_OMAP2) += omap_device.o
> obj-$(CONFIG_ARCH_OMAP3) += omap_device.o
> +obj-$(CONFIG_ARCH_OMAP3) += pmc.o
>
> obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o
> obj-$(CONFIG_OMAP_IOMMU) += iommu.o iovmm.o
> diff --git a/arch/arm/plat-omap/include/plat/pmc.h b/arch/arm/plat-omap/include/plat/pmc.h
> new file mode 100644
> index 0000000..6d73782
> --- /dev/null
> +++ b/arch/arm/plat-omap/include/plat/pmc.h
> @@ -0,0 +1,9 @@
> +#ifndef __PMC_H__
> +#define __PMC_H__
> +extern void start_perf_counter(void);
> +extern void start_cycle_counter(void);
> +extern void stop_cycle_counter(void);
> +extern void stop_perf_counter(void);
> +extern unsigned int cycle_count(void);
> +extern unsigned int delay_sram;
> +#endif
> diff --git a/arch/arm/plat-omap/include/plat/sram.h b/arch/arm/plat-omap/include/plat/sram.h
> index 16a1b45..6019ed8 100644
> --- a/arch/arm/plat-omap/include/plat/sram.h
> +++ b/arch/arm/plat-omap/include/plat/sram.h
> @@ -69,6 +69,12 @@ extern u32 omap3_sram_configure_core_dpll(
> u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1);
> extern unsigned long omap3_sram_configure_core_dpll_sz;
>
> +extern unsigned int measure_sram_delay(unsigned int);
> +
> +extern u32 __sram_wait_delay(
> + unsigned int);
> +extern unsigned long __sram_wait_delay_sz;
> +
> #ifdef CONFIG_PM
> extern void omap_push_sram_idle(void);
> #else
> diff --git a/arch/arm/plat-omap/pmc.c b/arch/arm/plat-omap/pmc.c
> new file mode 100644
> index 0000000..11acf42
> --- /dev/null
> +++ b/arch/arm/plat-omap/pmc.c
> @@ -0,0 +1,47 @@
> +#include <linux/module.h>
> +
> +void start_perf_counter(void)
> +{
> + unsigned int r1 = 0;
blank line needed
> + asm("mrc p15, 0, %0, c9, c12, 0" : "=r" (r1));
> + r1 |= 0x1; /* enable counters */
> + asm("mcr p15, 0, %0, c9, c12, 0" : : "r" (r1));
> + return;
> +}
> +EXPORT_SYMBOL(start_perf_counter);
export not needed (on any of these functions)
> +void start_cycle_counter(void)
> +{
> + unsigned int r2 = 0;
blank line needed, assignment not necessary
> + r2 = 0x80000000; /* enable cycle counter only */
> + asm("mcr p15, 0, %0, c9, c12, 1" : : "r" (r2));
> + return;
> +}
> +EXPORT_SYMBOL(start_cycle_counter);
> +
> +unsigned int cycle_count(void)
> +{
> + unsigned int rd = 0;
blank line
> + asm("mrc p15, 0, %0, c9, c13, 0" : "=r" (rd));
> + return rd;
> +}
> +EXPORT_SYMBOL(cycle_count);
> +
> +
> +void stop_cycle_counter(void)
> +{
> + unsigned int r3 = 0;
blank line, assignment not needed
> + r3 = 0x0; /* disable cycle counter */
> + asm("mcr p15, 0, %0, c9, c12, 1" : : "r" (r3));
> + return;
> +}
> +EXPORT_SYMBOL(stop_cycle_counter);
> +
> +void stop_perf_counter(void)
> +{
> + unsigned int r1 = 0;
ditto
> + r1 = 0x0; /* disable counters */
> + asm("mcr p15, 0, %0, c9, c12, 0" : : "r" (r1));
> + return;
> +}
> +EXPORT_SYMBOL(stop_perf_counter);
> diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c
> index 3e92366..4ed6a48 100644
> --- a/arch/arm/plat-omap/sram.c
> +++ b/arch/arm/plat-omap/sram.c
> @@ -29,6 +29,10 @@
> #include <plat/board.h>
> #include <plat/cpu.h>
>
> +#ifdef CONFIG_ARCH_OMAP3
> +#include <plat/pmc.h>
> +#endif
> +
> #include <plat/control.h>
>
> #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
> @@ -423,6 +427,25 @@ static inline int omap34xx_sram_init(void)
> }
> #endif
>
> +
> +#ifdef CONFIG_ARCH_OMAP3
> +unsigned int measure_sram_delay(unsigned int loop)
> +{
> + unsigned int start = 0, end = 0;
> + void (*_omap3_sram_delay)(unsigned long);
> + _omap3_sram_delay = omap_sram_push(__sram_wait_delay,
> + __sram_wait_delay_sz);
> + start_perf_counter();
> + start_cycle_counter();
> + start = cycle_count();
> + _omap3_sram_delay(loop);
> + end = cycle_count();
> + stop_cycle_counter();
> + stop_perf_counter();
> + return end - start;
> +}
> +#endif
> +
> int __init omap_sram_init(void)
> {
> omap_detect_sram();
> --
Kevin
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
