Re: [PATCH v9 08/10] PCI: dwc: ep: Add a generic dw_pcie_ep_linkdown() API to handle LINK_DOWN event

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Mar 08, 2024 at 09:56:33AM +0100, Niklas Cassel wrote:
> On Fri, Mar 08, 2024 at 11:11:52AM +0530, Manivannan Sadhasivam wrote:
> > On Thu, Mar 07, 2024 at 10:43:19PM +0100, Niklas Cassel wrote:
> > > On Mon, Mar 04, 2024 at 02:52:20PM +0530, Manivannan Sadhasivam wrote:
> > > > The PCIe link can go to LINK_DOWN state in one of the following scenarios:
> > > > 
> > > > 1. Fundamental (PERST#)/hot/warm reset
> > > > 2. Link transition from L2/L3 to L0
> > > > 
> > > > In those cases, LINK_DOWN causes some non-sticky DWC registers to loose the
> > > > state (like REBAR, PTM_CAP etc...). So the drivers need to reinitialize
> > > > them to function properly once the link comes back again.
> > > > 
> > > > This is not a problem for drivers supporting PERST# IRQ, since they can
> > > > reinitialize the registers in the PERST# IRQ callback. But for the drivers
> > > > not supporting PERST#, there is no way they can reinitialize the registers
> > > > other than relying on LINK_DOWN IRQ received when the link goes down. So
> > > > let's add a DWC generic API dw_pcie_ep_linkdown() that reinitializes the
> > > > non-sticky registers and also notifies the EPF drivers about link going
> > > > down.
> > > > 
> > > > This API can also be used by the drivers supporting PERST# to handle the
> > > > scenario (2) mentioned above.
> > > > 
> > > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>
> > > > ---
> > > >  drivers/pci/controller/dwc/pcie-designware-ep.c | 111 ++++++++++++++----------
> > > >  drivers/pci/controller/dwc/pcie-designware.h    |   5 ++
> > > >  2 files changed, 72 insertions(+), 44 deletions(-)
> > > > 
> > > > diff --git a/drivers/pci/controller/dwc/pcie-designware-ep.c b/drivers/pci/controller/dwc/pcie-designware-ep.c
> > > > index 278bdc9b2269..fed4c2936c78 100644
> > > > --- a/drivers/pci/controller/dwc/pcie-designware-ep.c
> > > > +++ b/drivers/pci/controller/dwc/pcie-designware-ep.c
> > > > @@ -14,14 +14,6 @@
> > > >  #include <linux/pci-epc.h>
> > > >  #include <linux/pci-epf.h>
> > > >  
> > > > -void dw_pcie_ep_linkup(struct dw_pcie_ep *ep)
> > > > -{
> > > > -	struct pci_epc *epc = ep->epc;
> > > > -
> > > > -	pci_epc_linkup(epc);
> > > > -}
> > > > -EXPORT_SYMBOL_GPL(dw_pcie_ep_linkup);
> > > > -
> > > >  void dw_pcie_ep_init_notify(struct dw_pcie_ep *ep)
> > > >  {
> > > >  	struct pci_epc *epc = ep->epc;
> > > > @@ -603,19 +595,56 @@ static unsigned int dw_pcie_ep_find_ext_capability(struct dw_pcie *pci, int cap)
> > > >  	return 0;
> > > >  }
> > > >  
> > > > +static void dw_pcie_ep_init_non_sticky_registers(struct dw_pcie *pci)
> > > > +{
> > > > +	unsigned int offset, ptm_cap_base;
> > > > +	unsigned int nbars;
> > > > +	u32 reg, i;
> > > > +
> > > > +	offset = dw_pcie_ep_find_ext_capability(pci, PCI_EXT_CAP_ID_REBAR);
> > > > +	ptm_cap_base = dw_pcie_ep_find_ext_capability(pci, PCI_EXT_CAP_ID_PTM);
> > > > +
> > > > +	dw_pcie_dbi_ro_wr_en(pci);
> > > > +
> > > > +	if (offset) {
> > > > +		reg = dw_pcie_readl_dbi(pci, offset + PCI_REBAR_CTRL);
> > > > +		nbars = (reg & PCI_REBAR_CTRL_NBAR_MASK) >>
> > > > +			PCI_REBAR_CTRL_NBAR_SHIFT;
> > > > +
> > > > +		for (i = 0; i < nbars; i++, offset += PCI_REBAR_CTRL)
> > > > +			dw_pcie_writel_dbi(pci, offset + PCI_REBAR_CAP, 0x0);
> > > 
> > > If you look at PCI_REBAR_CAP, you will see that it is sticky,
> > > but you have to actually read the databook to see that:
> > > 
> > > "The RESBAR_CTRL_REG_BAR_SIZE field is automatically updated
> > > when you write to RESBAR_CAP_REG_0_REG through the DBI."
> > > 
> > > So the reason why we need to write this register, even though
> > > it is sticky, is to update the RESBAR_CTRL_REG_BAR_SIZE register,
> > > which is not sticky :)
> > > 
> > > (Perhaps we should add that as a comment?)
> > > 
> > 
> > Yeah, makes sense.
> 
> Note that I add a (unrelated) comment related to REBAR_CAP in this patch:
> https://lore.kernel.org/linux-pci/20240307111520.3303774-1-cassel@xxxxxxxxxx/T/#u
> 
> But once we move/add code to dw_pcie_ep_init_non_sticky_registers(), I think
> that it might be a good "rule" to have a small comment for each write in
> dw_pcie_ep_init_non_sticky_registers() which explains why the code should be
> in dw_pcie_ep_init_non_sticky_registers() instead of dw_pcie_ep_init_registers(),
> even if it just a small:
> 
> /* Field PCI_XXX_YYY.ZZZ is non-sticky */
> writel_dbi(pci, offset + PCI_XXX_YYY, 0);
> 

Why? The function name itself suggests that we are reinitializing non-sticky
registers. So a comment for each write is overkill.

- Mani

-- 
மணிவண்ணன் சதாசிவம்




[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux