The Phytec PCM-959 is a development platform for the Phytec PCM-049 SOM.
Add initial functionality for the board. The verified interfaces and
peripherals are listed below for the SOM (PCM-049) and the dev board
(PCM-959)
The omap2plus_defconfig was used for testing. Only the On-board LEDs
required CONFIG_LEDS_PCA9532 addition.
PCM-049:
i2c1
* EEPROM at 0x50
* TMP102 (hwmon) at 0x4b
twl6030
GPMC
* Ethernet
* Flash
Serial (ttyS2 console)
PCM959:
MMC1
On-board LEDs (with CONFIG_LEDS_PCA9532)
Signed-off-by: Colin Foster <colin.foster@xxxxxxxxxxxxxxxx>
---
v3->v4
* Remove unnecessary "omap-4430" compatible string
v2->v3
Code review changes:
* Remove unnecessary "okay" statuses
* Utilize gpio funciton / color instead of label
* Clean up pinctrl whitespace
* Change label of TWL6030 to "pmic"
* Clean up general whitespace
Behavioral changes:
* Utilize "gpmc-wait" instead of "rb-gpios". The initial
configuration would suffer about a 1/100K NAND access
failure, snowballing into corrupted NAND after enough
boot cycles / downloads. This one was fun to figure out!
* Adjustments to gpmc-nand timings from testing.
v1->v2
* Almost everything moved to the SOM (PCM049)
* Fix where omap_pmx_wkup were actually getting applied to
omap_pmx_core.
* Use hyphens instead of underscores for names
* Remove unnecessary entries of "status=okay"
* Use generic "regulator" and "led" names
* add compatible strings for the dev board and SOM
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi | 400 ++++++++++++++++++++
arch/arm/boot/dts/omap4-phytec-pcm-959.dts | 48 +++
3 files changed, 449 insertions(+)
create mode 100644 arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi
create mode 100644 arch/arm/boot/dts/omap4-phytec-pcm-959.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 6aa7dc4db2fc..ae8338cb5bb1 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -968,6 +968,7 @@ dtb-$(CONFIG_ARCH_OMAP4) += \
omap4-panda.dtb \
omap4-panda-a4.dtb \
omap4-panda-es.dtb \
+ omap4-phytec-pcm-959.dtb \
omap4-sdp.dtb \
omap4-sdp-es23plus.dtb \
omap4-var-dvk-om44.dtb \
diff --git a/arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi b/arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi
new file mode 100644
index 000000000000..3cc029599224
--- /dev/null
+++ b/arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi
@@ -0,0 +1,400 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2022 Innovative Advantage, Inc.
+ */
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>; /* 1 GB */
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dsp_memory_region: dsp-memory@98000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x98000000 0x800000>;
+ reusable;
+ };
+
+ ipu_memory_region: ipu-memory@98800000 {
+ compatible = "shared-dma-pool";
+ reg = <0x98800000 0x7000000>;
+ reusable;
+ };
+ };
+
+ chosen {
+ stdout-path = &uart3;
+ };
+
+ leds: leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_gpio_pins>;
+
+ led-0 {
+ function = LED_FUNCTION_HEARTBEAT;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio5 0x18 GPIO_ACTIVE_HIGH>; /* GPIO 152 */
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-1 {
+ function = LED_FUNCTION_DISK;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio5 0x19 GPIO_ACTIVE_HIGH>; /* GPIO 153 */
+ linux,default-trigger = "mmc0";
+ };
+ };
+};
+
+&gpio1_target {
+ ti,no-reset-on-init;
+};
+
+&omap4_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <&tps62361_pins>;
+
+ i2c1_pins: pinmux-i2c1-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
+ OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
+ >;
+ };
+
+ i2c3_pins: pinmux-i2c3-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
+ OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
+ >;
+ };
+
+ i2c4_pins: pinmux-i2c4-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
+ OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
+ >;
+ };
+
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE1) /* uart1_rx */
+ OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE1) /* uart1_tx */
+ >;
+ };
+
+ uart2_pins: pinmux-uart2-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts */
+ OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0) /* uart2_rts */
+ OMAP4_IOPAD(0x11c, PIN_INPUT | MUX_MODE0) /* uart2_rx */
+ OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
+ >;
+ };
+
+ uart3_pins: pinmux-uart3-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x140, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_cts */
+ OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE0) /* uart3_rts */
+ OMAP4_IOPAD(0x144, PIN_INPUT | MUX_MODE0) /* uart3_rx */
+ OMAP4_IOPAD(0x146, PIN_OUTPUT | MUX_MODE0) /* uart3_tx */
+ >;
+ };
+
+ led_gpio_pins: pinmux-leds-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x156, PIN_OUTPUT | MUX_MODE3) /* gpio_152 */
+ OMAP4_IOPAD(0x158, PIN_OUTPUT | MUX_MODE3) /* gpio_153 */
+ >;
+ };
+
+ pinctrl_tempsense: pinmux-pinctrl-tempsense-pins{
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x154, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio_151 */
+ >;
+ };
+
+ gpmc_pins: gpmc-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x40, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad0 */
+ OMAP4_IOPAD(0x42, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad1 */
+ OMAP4_IOPAD(0x44, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad2 */
+ OMAP4_IOPAD(0x46, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad3 */
+ OMAP4_IOPAD(0x48, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad4 */
+ OMAP4_IOPAD(0x4a, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad5 */
+ OMAP4_IOPAD(0x4c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad6 */
+ OMAP4_IOPAD(0x4e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad7 */
+ OMAP4_IOPAD(0x50, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad8 */
+ OMAP4_IOPAD(0x52, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad9 */
+ OMAP4_IOPAD(0x54, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad10 */
+ OMAP4_IOPAD(0x56, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad11 */
+ OMAP4_IOPAD(0x58, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad12 */
+ OMAP4_IOPAD(0x5a, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad13 */
+ OMAP4_IOPAD(0x5c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad14 */
+ OMAP4_IOPAD(0x5e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad15 */
+
+ OMAP4_IOPAD(0x60, PIN_OUTPUT | MUX_MODE0) /* gpmc_a16 */
+ OMAP4_IOPAD(0x62, PIN_OUTPUT | MUX_MODE0) /* gpmc_a17 */
+ OMAP4_IOPAD(0x64, PIN_OUTPUT | MUX_MODE0) /* gpmc_a18 */
+ OMAP4_IOPAD(0x66, PIN_OUTPUT | MUX_MODE0) /* gpmc_a19 */
+ OMAP4_IOPAD(0x68, PIN_OUTPUT | MUX_MODE0) /* gpmc_a20 */
+ OMAP4_IOPAD(0x6a, PIN_OUTPUT | MUX_MODE0) /* gpmc_a21 */
+ OMAP4_IOPAD(0x6c, PIN_OUTPUT | MUX_MODE0) /* gpmc_a22 */
+ OMAP4_IOPAD(0x6e, PIN_OUTPUT | MUX_MODE0) /* gpmc_a23 */
+
+ OMAP4_IOPAD(0x82, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_noe */
+ OMAP4_IOPAD(0x84, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_nwe */
+
+ OMAP4_IOPAD(0x7c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_nwp */
+ OMAP4_IOPAD(0x80, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_nadv_ale */
+ OMAP4_IOPAD(0x86, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_nbe0_cle */
+ OMAP4_IOPAD(0x8a, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0 */
+ OMAP4_IOPAD(0x8c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait1 */
+
+ OMAP4_IOPAD(0x74, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_ncs0 */
+ OMAP4_IOPAD(0x76, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_ncs1 */
+ OMAP4_IOPAD(0x92, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_ncs5 */
+ >;
+ };
+
+ ethernet_pins: ethernet-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x114, PIN_INPUT | MUX_MODE3) /* gpio_121 */
+ >;
+ };
+
+ tps62361_pins: pinmux-tps62361-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x19c, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpio_182 */
+ >;
+ };
+
+ mmc1_pins: pinmux-mmc1-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x0e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
+ OMAP4_IOPAD(0x0e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
+ OMAP4_IOPAD(0x0e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */
+ OMAP4_IOPAD(0x0e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
+ OMAP4_IOPAD(0x0ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
+ OMAP4_IOPAD(0x0ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
+ >;
+ };
+};
+
+&omap4_pmx_wkup {
+ pinctrl-names = "default";
+ pinctrl-0= <&smartreflex_i2c_pins &fref_xtal_in_pins
+ &fref_clk3_out_pins &sys_pins>;
+
+ ethernet_wkgpio_pins: pinmux-ethernet-wkup-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x66, PIN_OUTPUT | MUX_MODE3) /* gpio_wk29 */
+ >;
+ };
+
+ smartreflex_i2c_pins: pinmux-smartreflex-i2c-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x4a, PIN_INPUT_PULLUP | MUX_MODE0) /* sr_scl */
+ OMAP4_IOPAD(0x4c, PIN_INPUT_PULLUP | MUX_MODE0) /* sr_sda */
+ >;
+ };
+
+ fref_xtal_in_pins: pinmux-fref-xtal-in-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x4e, PIN_OUTPUT | MUX_MODE0) /* fref_xtal_in */
+ >;
+ };
+
+ fref_clk3_out_pins: pinmux-usb-refclk-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x58, PIN_OUTPUT | MUX_MODE0) /* fref_clk3_out */
+ >;
+ };
+
+ sys_pins: pinmux-sys-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x5e, PIN_INPUT | MUX_MODE0) /* sys_32k */
+ OMAP4_IOPAD(0x60, PIN_OUTPUT | MUX_MODE0) /* sys_nrespwron */
+ OMAP4_IOPAD(0x62, PIN_OUTPUT | MUX_MODE0) /* sys_nreswarm */
+ OMAP4_IOPAD(0x64, PIN_OUTPUT_PULLUP | MUX_MODE0) /* sys_pwr_req */
+ OMAP4_IOPAD(0x68, PIN_INPUT | MUX_MODE0) /* sys_boot6 */
+ OMAP4_IOPAD(0x6a, PIN_INPUT | MUX_MODE0) /* sys_boot7 */
+ >;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ clock-frequency = <400000>;
+
+ twl: pmic@48 {
+ compatible = "ti,twl6030";
+ reg = <0x48>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
+ };
+
+ core_vdd_reg: regulator@60 {
+ compatible = "ti,tps62361";
+ reg = <0x60>;
+
+ regulator-name = "tps62361-vout";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-coupled-max-spread = <300000>;
+ regulator-max-step-microvolt = <100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ ti,vsel0-gpio = <&gpio5 22 GPIO_ACTIVE_HIGH>;
+ ti,vsel0-state-high;
+ };
+
+ temperature-sensor@4b {
+ compatible = "ti,tmp102";
+ reg = <0x4b>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tempsense>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c32";
+ reg = <0x50>;
+ };
+};
+
+#include "twl6030.dtsi"
+#include "twl6030_omap4.dtsi"
+
+&i2c2 {
+ status = "disabled";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+ status = "okay";
+
+ clock-frequency = <100000>;
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins>;
+ status = "disabled";
+
+ clock-frequency = <400000>;
+};
+
+&vmmc {
+ ti,retain-on-reset;
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+
+ vmmc-supply = <&vmmc>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc2 {
+ status = "disabled";
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&mmc4 {
+ status = "disabled";
+};
+
+&mmc5 {
+ status = "disabled";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "okay";
+};
+
+&uart4 {
+ status = "disabled";
+};
+
+&elm {
+ status = "okay";
+};
+
+#include "omap-gpmc-smsc9221.dtsi"
+
+&gpmc {
+ ranges = <5 0 0x2c000000 0x01000000>,
+ <0 0 0x08000000 0x01000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmc_pins>;
+ status = "okay";
+
+ nandflash: nand@0,0 {
+ compatible = "ti,omap2-nand";
+ reg = <0 0 4>;
+ interrupt-parent = <&gpmc>;
+
+ nand-bus-width = <16>;
+ ti,nand-ecc-opt = "bch8";
+ ti,elm-id=<&elm>;
+ linux,mtd-name = "micron,nand";
+ gpmc,device-nand = "true";
+ gpmc,device-width = <1>;
+
+ gpmc,cs-rd-off-ns = <40>;
+ gpmc,cs-wr-off-ns = <40>;
+ gpmc,adv-rd-off-ns = <25>;
+ gpmc,adv-wr-off-ns = <40>;
+ gpmc,oe-off-ns = <50>;
+ gpmc,we-off-ns = <30>;
+ gpmc,rd-cycle-ns = <75>;
+ gpmc,wr-cycle-ns = <75>;
+ gpmc,access-ns = <55>;
+ gpmc,wr-access-ns = <55>;
+ gpmc,wait-pin = <0>;
+ gpmc,wait-on-write = "true";
+ gpmc,wait-on-read = "true";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ ethernet@gpmc {
+ reg = <5 0 0xff>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <ðernet_pins ðernet_wkgpio_pins>;
+
+ /* Either GPIO 103 or GPIO 121. Use 121 to match the reference design */
+ interrupt-parent = <&gpio4>;
+ interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
diff --git a/arch/arm/boot/dts/omap4-phytec-pcm-959.dts b/arch/arm/boot/dts/omap4-phytec-pcm-959.dts
new file mode 100644
index 000000000000..e1fee183d4c9
--- /dev/null
+++ b/arch/arm/boot/dts/omap4-phytec-pcm-959.dts
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2022 Innovative Advantage, Inc.
+ */
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+#include "omap4460.dtsi"
+#include "omap4-phytec-pcm-049.dtsi"
+
+/ {
+ model = "Phytec PCM-959 Eval Board";
+ compatible = "phytec,pcm959", "phytec,pcm049", "ti,omap4460", "ti,omap4";
+};
+
+&i2c4 {
+ status = "okay";
+
+ leddim: led@62 {
+ compatible = "nxp,pca9533";
+ reg = <0x62>;
+
+ led-1 {
+ color = <LED_COLOR_ID_RED>;
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led-2 {
+ color = <LED_COLOR_ID_YELLOW>;
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led-3 {
+ color = <LED_COLOR_ID_YELLOW>;
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led-4 {
+ color = <LED_COLOR_ID_GREEN>;
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+ };
+};
--
2.25.1
