Re: [PATCH v4 1/2] dt-bindings: net: Add ICSSG Ethernet Driver bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 06/02/2023 07:07, MD Danish Anwar wrote:
> From: Puranjay Mohan <p-mohan@xxxxxx>
> 
> Add a YAML binding document for the ICSSG Programmable real time unit
> based Ethernet driver. This driver uses the PRU and PRUSS consumer APIs

You add a binding for the hardware, not for driver.

> to interface the PRUs and load/run the firmware for supporting ethernet
> functionality.

Subject: drop second/last, redundant "driver bindings". The
"dt-bindings" prefix is already stating that these are bindings.

> 
> Signed-off-by: Puranjay Mohan <p-mohan@xxxxxx>
> Signed-off-by: Md Danish Anwar <danishanwar@xxxxxx>
> ---
>  .../bindings/net/ti,icssg-prueth.yaml         | 179 ++++++++++++++++++
>  1 file changed, 179 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
> 
> diff --git a/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
> new file mode 100644
> index 000000000000..e4dee01a272a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
> @@ -0,0 +1,179 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/ti,icssg-prueth.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Texas Instruments ICSSG PRUSS Ethernet
> +
> +maintainers:
> +  - Md Danish Anwar <danishanwar@xxxxxx>
> +
> +description:
> +  Ethernet based on the Programmable Real-Time
> +  Unit and Industrial Communication Subsystem.
> +
> +allOf:
> +  - $ref: /schemas/remoteproc/ti,pru-consumer.yaml#
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ti,am654-icssg-prueth  # for AM65x SoC family
> +
> +  ti,sram:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description:
> +      phandle to MSMC SRAM node
> +
> +  dmas:
> +    maxItems: 10
> +
> +  dma-names:
> +    items:
> +      - const: tx0-0
> +      - const: tx0-1
> +      - const: tx0-2
> +      - const: tx0-3
> +      - const: tx1-0
> +      - const: tx1-1
> +      - const: tx1-2
> +      - const: tx1-3
> +      - const: rx0
> +      - const: rx1
> +
> +  ethernet-ports:

Bring some order or logic in the order of the properties. Keep the
ethernet-ports as last property.

> +    type: object
> +    additionalProperties: false

Blank line

> +    properties:
> +      '#address-cells':
> +        const: 1
> +      '#size-cells':
> +        const: 0
> +
> +    patternProperties:
> +      ^port@[0-1]$:
> +        type: object
> +        description: ICSSG PRUETH external ports
> +

Drop blank line

> +        $ref: ethernet-controller.yaml#
> +

Drop blank line

> +        unevaluatedProperties: false
> +
> +        properties:
> +          reg:
> +            items:
> +              - enum: [0, 1]
> +            description: ICSSG PRUETH port number
> +
> +          interrupts-extended:

Just "interrupts"
> +            maxItems: 1
> +
> +          ti,syscon-rgmii-delay:
> +            items:
> +              - items:
> +                  - description: phandle to system controller node
> +                  - description: The offset to ICSSG control register
> +            $ref: /schemas/types.yaml#/definitions/phandle-array
> +            description:
> +              phandle to system controller node and register offset
> +              to ICSSG control register for RGMII transmit delay
> +
> +        required:
> +          - reg

required for ethernet-ports - at least one port is required, isn't it?
> +
> +  ti,mii-g-rt:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description: |
> +      phandle to MII_G_RT module's syscon regmap.
> +
> +  ti,mii-rt:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description: |
> +      phandle to MII_RT module's syscon regmap
> +
> +  interrupts:
> +    maxItems: 2
> +    description: |
> +      Interrupt specifiers to TX timestamp IRQ.
> +
> +  interrupt-names:
> +    items:
> +      - const: tx_ts0
> +      - const: tx_ts1
> +
> +required:
> +  - compatible
> +  - ti,sram
> +  - dmas
> +  - dma-names
> +  - ethernet-ports
> +  - ti,mii-g-rt
> +  - interrupts
> +  - interrupt-names
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    /* Example k3-am654 base board SR2.0, dual-emac */
> +    pruss2_eth: ethernet {
> +        compatible = "ti,am654-icssg-prueth";
> +        pinctrl-names = "default";
> +        pinctrl-0 = <&icssg2_rgmii_pins_default>;
> +        ti,sram = <&msmc_ram>;
> +
> +        ti,prus = <&pru2_0>, <&rtu2_0>, <&tx_pru2_0>,
> +                  <&pru2_1>, <&rtu2_1>, <&tx_pru2_1>;
> +        firmware-name = "ti-pruss/am65x-pru0-prueth-fw.elf",
> +                        "ti-pruss/am65x-rtu0-prueth-fw.elf",
> +                        "ti-pruss/am65x-txpru0-prueth-fw.elf",
> +                        "ti-pruss/am65x-pru1-prueth-fw.elf",
> +                        "ti-pruss/am65x-rtu1-prueth-fw.elf",
> +                        "ti-pruss/am65x-txpru1-prueth-fw.elf";
> +        ti,pruss-gp-mux-sel = <2>,      /* MII mode */
> +                              <2>,
> +                              <2>,
> +                              <2>,      /* MII mode */
> +                              <2>,
> +                              <2>;
> +        dmas = <&main_udmap 0xc300>, /* egress slice 0 */
> +               <&main_udmap 0xc301>, /* egress slice 0 */
> +               <&main_udmap 0xc302>, /* egress slice 0 */
> +               <&main_udmap 0xc303>, /* egress slice 0 */
> +               <&main_udmap 0xc304>, /* egress slice 1 */
> +               <&main_udmap 0xc305>, /* egress slice 1 */
> +               <&main_udmap 0xc306>, /* egress slice 1 */
> +               <&main_udmap 0xc307>, /* egress slice 1 */
> +               <&main_udmap 0x4300>, /* ingress slice 0 */
> +               <&main_udmap 0x4301>; /* ingress slice 1 */
> +        dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3",
> +                    "tx1-0", "tx1-1", "tx1-2", "tx1-3",
> +                    "rx0", "rx1";
> +        ti,mii-g-rt = <&icssg2_mii_g_rt>;
> +        interrupts = <24 0 2>, <25 1 3>;

Aren't you open-coding some IRQ flags?

> +        interrupt-names = "tx_ts0", "tx_ts1";
> +        ethernet-ports {


Best regards,
Krzysztof




[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux