Re: [PATCH v7 1/6] DONOTMERGE: arm64: dts: ti: Add TI TPS65219 PMIC support for AM642 SK board.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Jerome,

is this setup working for you on the AM642 SK board?

I am testing your PMIC patches on a AM62 based board with a similar setup and
running into the following error

    VDDSHV5_SDIO: bypassed regulator has no supply!
    VDDSHV5_SDIO: will resolve supply early: ldo1
    VDDSHV5_SDIO: supplied by regulator-dummy
    VDDSHV5_SDIO: failed to get the current voltage: -EINVAL

Have you noticed problems with LDO1 and bypass mode?

Regards,
Wadim

Am 04.11.22 um 16:23 schrieb Jerome Neanne:
> From: Jerome NEANNE <jneanne@xxxxxxxxxxxx>
>
> Add support fot the TI Power Management IC TPS65219
> on the AM642 SKEVM board.
>
> Needed for driver testing but official board support pending.
> TI commitment is required before board upstream kick-off.
>
> Signed-off-by: Jerome NEANNE <jneanne@xxxxxxxxxxxx>
> Signed-off-by: Markus Schneider-Pargmann <msp@xxxxxxxxxxxx>
> ---
>   arch/arm64/boot/dts/ti/k3-am642-sk.dts | 104 +++++++++++++++++++++++++
>   1 file changed, 104 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am642-sk.dts b/arch/arm64/boot/dts/ti/k3-am642-sk.dts
> index 738d0cf6c40a..d0121976491a 100644
> --- a/arch/arm64/boot/dts/ti/k3-am642-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am642-sk.dts
> @@ -219,6 +219,20 @@ led-7 {
>   			gpios = <&exp2 7 GPIO_ACTIVE_HIGH>;
>   		};
>   	};
> +
> +	vsel_sd_nddr: gpio-regulator {
> +		compatible = "regulator-gpio";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vsel_sd_nddr_pins_default>;
> +		regulator-name = "tps65219-LDO1-SEL-SD";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		vin-supply = <&ldo1_reg>;
> +		gpios = <&main_gpio0 45 GPIO_ACTIVE_HIGH>;
> +		states = <1800000 0x0>,
> +			 <3300000 0x1>;
> +	};
>   };
>   
>   &main_pmx0 {
> @@ -250,6 +264,13 @@ AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */
>   		>;
>   	};
>   
> +	main_i2c0_pins_default: main-i2c0-pins-default {
> +		pinctrl-single,pins = <
> +			AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */
> +			AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */
> +		>;
> +	};
> +
>   	main_i2c1_pins_default: main-i2c1-pins-default {
>   		pinctrl-single,pins = <
>   			AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */
> @@ -336,6 +357,12 @@ main_wlan_pins_default: main-wlan-pins-default {
>   			AM64X_IOPAD(0x00bc, PIN_INPUT, 7) /* (U8) GPIO0_46 */
>   		>;
>   	};
> +
> +	vsel_sd_nddr_pins_default: vsel-sd-nddr-pins-default {
> +		pinctrl-single,pins = <
> +			AM64X_IOPAD(0x00b8, PIN_INPUT, 7) /* (Y7) PRG1_PRU0_GPO0.GPIO0_45 */
> +		>;
> +	};
>   };
>   
>   &mcu_uart0 {
> @@ -384,6 +411,83 @@ &mcu_i2c1 {
>   	status = "disabled";
>   };
>   
> +&main_i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&main_i2c0_pins_default>;
> +	clock-frequency = <400000>;
> +	status = "okay";
> +
> +	tps65219: pmic@30 {
> +		compatible = "ti,tps65219";
> +		reg = <0x30>;
> +		system-power-controller;
> +
> +		buck1-supply = <&vcc_3v3_sys>;
> +		buck2-supply = <&vcc_3v3_sys>;
> +		buck3-supply = <&vcc_3v3_sys>;
> +		ldo1-supply = <&vcc_3v3_sys>;
> +		ldo2-supply = <&buck2_reg>;
> +		ldo3-supply = <&vcc_3v3_sys>;
> +		ldo4-supply = <&vcc_3v3_sys>;
> +
> +		regulators {
> +			buck1_reg: buck1 {
> +				regulator-name = "VDD_CORE";
> +				regulator-min-microvolt = <750000>;
> +				regulator-max-microvolt = <1000000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			buck2_reg: buck2 {
> +				regulator-name = "VCC1V8";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			buck3_reg: buck3 {
> +				regulator-name = "VDD_LPDDR4";
> +				regulator-min-microvolt = <1100000>;
> +				regulator-max-microvolt = <1100000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo1_reg: ldo1 {
> +				regulator-name = "VDDSHV_SD_IO_PMIC";
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-allow-bypass;
> +			};
> +
> +			ldo2_reg: ldo2 {
> +				regulator-name = "VDDAR_CORE";
> +				regulator-min-microvolt = <850000>;
> +				regulator-max-microvolt = <850000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo3_reg: ldo3 {
> +				regulator-name = "VDDA_1V8";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			ldo4_reg: ldo4 {
> +				regulator-name = "VDD_PHY_2V5";
> +				regulator-min-microvolt = <2500000>;
> +				regulator-max-microvolt = <2500000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +		};
> +	};
> +};
>   &main_i2c1 {
>   	pinctrl-names = "default";
>   	pinctrl-0 = <&main_i2c1_pins_default>;






[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux