From: Benedikt Niedermayr <benedikt.niedermayr@xxxxxxxxxxx>
The waitpin polarity can be configured via the WAITPIN<X>POLARITY bits
in the GPMC_CONFIG register. This is currently not supported by the
driver. This patch adds support for setting the required register bits
with the "gpmc,wait-pin-polarity" dt-property.
Signed-off-by: Benedikt Niedermayr <benedikt.niedermayr@xxxxxxxxxxx>
---
drivers/memory/omap-gpmc.c | 22 ++++++++++++++++++++++
include/linux/platform_data/gpmc-omap.h | 6 ++++++
2 files changed, 28 insertions(+)
diff --git a/drivers/memory/omap-gpmc.c b/drivers/memory/omap-gpmc.c
index e3674a15b934..66dd7dd80653 100644
--- a/drivers/memory/omap-gpmc.c
+++ b/drivers/memory/omap-gpmc.c
@@ -132,6 +132,7 @@
#define GPMC_CONFIG_DEV_SIZE 0x00000002
#define GPMC_CONFIG_DEV_TYPE 0x00000003
+#define GPMC_CONFIG_WAITPINPOLARITY(pin) (BIT(pin) << 8)
#define GPMC_CONFIG1_WRAPBURST_SUPP (1 << 31)
#define GPMC_CONFIG1_READMULTIPLE_SUPP (1 << 30)
#define GPMC_CONFIG1_READTYPE_ASYNC (0 << 29)
@@ -1881,6 +1882,21 @@ int gpmc_cs_program_settings(int cs, struct gpmc_settings *p)
gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1, config1);
+ if (p->wait_on_read || p->wait_on_write) {
+ config1 = gpmc_read_reg(GPMC_CONFIG);
+
+ if (p->wait_pin_polarity == WAITPINPOLARITY_ACTIVE_LOW)
+ config1 &= ~GPMC_CONFIG_WAITPINPOLARITY(p->wait_pin);
+ else if (p->wait_pin_polarity == WAITPINPOLARITY_ACTIVE_HIGH)
+ config1 |= GPMC_CONFIG_WAITPINPOLARITY(p->wait_pin);
+ else if (p->wait_pin_polarity != WAITPINPOLARITY_DEFAULT)
+ pr_err("%s: invalid wait-pin-polarity (pin: %d, polarity: %d)\n",
+ __func__, p->wait_pin, p->wait_pin_polarity);
+
+ gpmc_write_reg(GPMC_CONFIG, config1);
+ }
+
+
return 0;
}
@@ -1981,6 +1997,12 @@ void gpmc_read_settings_dt(struct device_node *np, struct gpmc_settings *p)
}
if (!of_property_read_u32(np, "gpmc,wait-pin", &p->wait_pin)) {
+
+ p->wait_pin_polarity = WAITPINPOLARITY_DEFAULT;
+ of_property_read_u32(np,
+ "gpmc,wait-pin-polarity",
+ &p->wait_pin_polarity);
+
p->wait_on_read = of_property_read_bool(np,
"gpmc,wait-on-read");
p->wait_on_write = of_property_read_bool(np,
diff --git a/include/linux/platform_data/gpmc-omap.h b/include/linux/platform_data/gpmc-omap.h
index c9cc4e32435d..c46c28069c31 100644
--- a/include/linux/platform_data/gpmc-omap.h
+++ b/include/linux/platform_data/gpmc-omap.h
@@ -136,6 +136,11 @@ struct gpmc_device_timings {
#define GPMC_MUX_AAD 1 /* Addr-Addr-Data multiplex */
#define GPMC_MUX_AD 2 /* Addr-Data multiplex */
+/* Wait pin polarity values */
+#define WAITPINPOLARITY_DEFAULT -1
+#define WAITPINPOLARITY_ACTIVE_LOW 0
+#define WAITPINPOLARITY_ACTIVE_HIGH 1
+
struct gpmc_settings {
bool burst_wrap; /* enables wrap bursting */
bool burst_read; /* enables read page/burst mode */
@@ -149,6 +154,7 @@ struct gpmc_settings {
u32 device_width; /* device bus width (8 or 16 bit) */
u32 mux_add_data; /* multiplex address & data */
u32 wait_pin; /* wait-pin to be used */
+ u32 wait_pin_polarity; /* wait-pin polarity */
};
/* Data for each chip select */
--
2.34.1
