Re: [PATCH 05/40] dt-bindings: touchscreen: ti,am3359-tsc: Remove deprecated text file

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, 25 Aug 2021 17:24:43 +0200
Miquel Raynal <miquel.raynal@xxxxxxxxxxx> wrote:

> Now that the three hardware peaces described in this file have been
> translated in yaml in 3 dedicated files (MFD, touchscreen controller and
> ADC) it is time to remove this text file.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>

Acked-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>

Nice to have another one of these go away :)
> ---
>  .../bindings/input/touchscreen/ti-tsc-adc.txt | 91 -------------------
>  1 file changed, 91 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
> 
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
> deleted file mode 100644
> index aad5e34965eb..000000000000
> --- a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
> +++ /dev/null
> @@ -1,91 +0,0 @@
> -* TI - TSC ADC (Touschscreen and analog digital converter)
> -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> -
> -Required properties:
> -- mfd
> -	compatible: Should be
> -		"ti,am3359-tscadc" for AM335x/AM437x SoCs
> -		"ti,am654-tscadc", "ti,am3359-tscadc" for AM654 SoCs
> -- child "tsc"
> -	compatible: Should be "ti,am3359-tsc".
> -	ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen
> -		  support on the platform.
> -	ti,x-plate-resistance: X plate resistance
> -	ti,coordinate-readouts: The sequencer supports a total of 16
> -				programmable steps each step is used to
> -				read a single coordinate. A single
> -                                readout is enough but multiple reads can
> -				increase the quality.
> -				A value of 5 means, 5 reads for X, 5 for
> -				Y and 2 for Z (always). This utilises 12
> -				of the 16 software steps available. The
> -				remaining 4 can be used by the ADC.
> -	ti,wire-config: Different boards could have a different order for
> -			connecting wires on touchscreen. We need to provide an
> -			8 bit number where in the 1st four bits represent the
> -			analog lines and the next 4 bits represent positive/
> -			negative terminal on that input line. Notations to
> -			represent the input lines and terminals resoectively
> -			is as follows:
> -			AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
> -			XP  = 0, XN = 1, YP = 2, YN = 3.
> -- child "adc"
> -	compatible: Should be
> -		    "ti,am3359-adc" for AM335x/AM437x SoCs
> -		    "ti,am654-adc", "ti,am3359-adc" for AM654 SoCs
> -	ti,adc-channels: List of analog inputs available for ADC.
> -			 AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
> -
> -Optional properties:
> -- child "tsc"
> -	ti,charge-delay: Length of touch screen charge delay step in terms of
> -			 ADC clock cycles. Charge delay value should be large
> -			 in order to avoid false pen-up events. This value
> -			 effects the overall sampling speed, hence need to be
> -			 kept as low as possible, while avoiding false pen-up
> -			 event. Start from a lower value, say 0x400, and
> -			 increase value until false pen-up events are avoided.
> -			 The pen-up detection happens immediately after the
> -			 charge step, so this does in fact function as a
> -			 hardware knob for adjusting the amount of "settling
> -			 time".
> -
> -- child "adc"
> -	ti,chan-step-opendelay: List of open delays for each channel of
> -				ADC in the order of ti,adc-channels. The
> -				value corresponds to the number of ADC
> -				clock cycles to wait after applying the
> -				step configuration registers and before
> -				sending the start of ADC conversion.
> -				Maximum value is 0x3FFFF.
> -       ti,chan-step-sampledelay: List of sample delays for each channel
> -				  of ADC in the order of ti,adc-channels.
> -				  The value corresponds to the number of
> -				  ADC clock cycles to sample (to hold
> -				  start of conversion high).
> -				  Maximum value is 0xFF.
> -       ti,chan-step-avg: Number of averages to be performed for each
> -			  channel of ADC. If average is 16 then input
> -			  is sampled 16 times and averaged to get more
> -			  accurate value. This increases the time taken
> -			  by ADC to generate a sample. Valid range is 0
> -			  average to 16 averages. Maximum value is 16.
> -
> -Example:
> -	tscadc: tscadc@44e0d000 {
> -		compatible = "ti,am3359-tscadc";
> -		tsc {
> -			ti,wires = <4>;
> -			ti,x-plate-resistance = <200>;
> -			ti,coordiante-readouts = <5>;
> -			ti,wire-config = <0x00 0x11 0x22 0x33>;
> -			ti,charge-delay = <0x400>;
> -		};
> -
> -		adc {
> -			ti,adc-channels = <4 5 6 7>;
> -			ti,chan-step-opendelay = <0x098 0x3ffff 0x098 0x0>;
> -			ti,chan-step-sampledelay = <0xff 0x0 0xf 0x0>;
> -			ti,chan-step-avg = <16 2 4 8>;
> -		};
> -	}




[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux