On Fri, 4 Jun 2021 12:39:54 +0300
Tony Lindgren <tony@xxxxxxxxxxx> wrote:
> * Andreas Kemnade <andreas@xxxxxxxxxxxx> [210604 08:35]:
> > I inserted some more dev-dbg
> > [ 60.241790] PM: suspend entry (deep)
> > [ 60.245513] Filesystems sync: 0.000 seconds
> > [ 60.251312] Freezing user space processes ... (elapsed 0.001 seconds) done.
> > [ 60.260040] OOM killer disabled.
> > [ 60.263275] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
> > [ 60.272338] printk: Suspending console(s) (use no_console_suspend to debug)
> > [ 60.281311] musb-omap2430 480ab000.usb_otg_hs: omap2430 runtime_resume
> > -> this is triggered by what?
>
> I think that comes from the pm_runtime_get_sync() in musb_suspend().
>
> > [ 60.281341] twl4030_usb 48070000.i2c:twl@48:twl4030-usb: twl4030_usb_runtime_resume
> > -> and here something stays on...
> >
> > [ 60.346374] twl4030_usb 48070000.i2c:twl@48:twl4030-usb: twl4030_phy_power_on
> > [ 60.796630] musb-hdrc musb-hdrc.0.auto: musb_suspend begin
> > [ 60.796722] musb-hdrc musb-hdrc.0.auto: musb_suspend end
> > [ 60.796752] musb-omap2430 480ab000.usb_otg_hs: omap2430 suspend
> > [ 60.796783] musb-omap2430 480ab000.usb_otg_hs: omap2430 runtime_suspend
> > [ 60.796783] twl4030_usb 48070000.i2c:twl@48:twl4030-usb: twl4030_phy_power_off
> > [ 60.796813] twl4030_usb 48070000.i2c:twl@48:twl4030-usb: twl4030_usb_suspend
> > [ 60.806549] Disabling non-boot CPUs ...
> > [ 60.806579] Successfully put all powerdomains to target state
>
> Well since commit 88d26136a256 ("PM: Prevent runtime suspend during system resume")
> nothing gets runtime idled during suspend with the extra pm_runtime_get_noresume()
> call in device_prepare() that does not get released until in device_complete().
>
> > forcing omap2430 runtime on before suspend:
> > [ 160.467742] musb-omap2430 480ab000.usb_otg_hs: omap2430 runtime_resume
> > [ 165.001495] PM: suspend entry (deep)
> > [ 165.005218] Filesystems sync: 0.000 seconds
> > [ 165.010284] Freezing user space processes ... (elapsed 0.001 seconds) done.
> > [ 165.018981] OOM killer disabled.
> > [ 165.022247] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
> > [ 165.031311] printk: Suspending console(s) (use no_console_suspend to debug)
> > [ 165.040496] musb-hdrc musb-hdrc.0.auto: musb_suspend begin
> > [ 165.040618] musb-hdrc musb-hdrc.0.auto: musb_suspend end
> > [ 165.040618] musb-omap2430 480ab000.usb_otg_hs: omap2430 suspend
> > [ 165.040649] musb-omap2430 480ab000.usb_otg_hs: omap2430 runtime_suspend
> > [ 165.040679] twl4030_usb 48070000.i2c:twl@48:twl4030-usb: twl4030_usb_suspend
> > [ 165.050506] Disabling non-boot CPUs ...
> > [ 165.050537] Successfully put all powerdomains to target state
>
> That's interesting. Hmm so we bail out early based on glue->is_runtime_suspended,
> and omap3 is still probing devices with omap_device.c instead of ti-sysc.c, so
> sounds like the duplicate calls you noticed might cause the issue.
>
> Does the following patch fix things for you or does something else break again? :)
>
sigh,..
ok, it breaks something. gadget (at least ecm) only works if
musb/phy stuff is loaded, ecm configured via configfs
rmmod omap2430
modprube 2430
until the next usb disconnect
and another rmmod/modprobe is required.
The following musb patches were applied additional to that one you
added to this mail on top of 5.13-rc4.
usb: musb: fix MUSB_QUIRK_B_DISCONNECT_99 handling
usb: musb: Add missing PM suspend and resume functions for 2430 glue
usb: musb: Check devctl status again for a spurious session request
Regards,
Andreas
