On 4/6/21 6:28 PM, Mathieu Poirier wrote:
> On Tue, Mar 23, 2021 at 05:38:37PM -0500, Suman Anna wrote:
>> The PRU firmware interrupt mapping logic in pru_handle_intrmap() uses
>> of_irq_find_parent() with PRU device node to get a handle to the PRUSS
>> Interrupt Controller at present. This logic however requires that the
>> PRU nodes always define a interrupt-parent property. This property is
>> neither a required/defined property as per the PRU remoteproc binding,
>> nor is relevant from a DT node point of view without any associated
>> interrupts. The curret logic finds a wrong interrupt controller and
>> fails to perform proper mapping without any interrupt-parent property
>> in the PRU nodes.
>>
>> Fix this logic to always find and use the sibling interrupt controller.
>> Also, while at this, fix the acquired interrupt controller device node
>> reference properly.
>>
>> Fixes: c75c9fdac66e ("remoteproc: pru: Add support for PRU specific interrupt configuration")
>> Signed-off-by: Suman Anna <s-anna@xxxxxx>
>> ---
>> drivers/remoteproc/pru_rproc.c | 15 ++++++++++++---
>> 1 file changed, 12 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/remoteproc/pru_rproc.c b/drivers/remoteproc/pru_rproc.c
>> index 16979c1cd2f4..a9d07c0751be 100644
>> --- a/drivers/remoteproc/pru_rproc.c
>> +++ b/drivers/remoteproc/pru_rproc.c
>> @@ -284,7 +284,7 @@ static int pru_handle_intrmap(struct rproc *rproc)
>> struct pru_rproc *pru = rproc->priv;
>> struct pru_irq_rsc *rsc = pru->pru_interrupt_map;
>> struct irq_fwspec fwspec;
>> - struct device_node *irq_parent;
>> + struct device_node *parent, *irq_parent;
>> int i, ret = 0;
>>
>> /* not having pru_interrupt_map is not an error */
>> @@ -312,9 +312,16 @@ static int pru_handle_intrmap(struct rproc *rproc)
>>
>> /*
>> * parse and fill in system event to interrupt channel and
>> - * channel-to-host mapping
>> + * channel-to-host mapping. The interrupt controller to be used
>> + * for these mappings for a given PRU remoteproc is always its
>> + * corresponding sibling PRUSS INTC node.
>> */
>> - irq_parent = of_irq_find_parent(pru->dev->of_node);
>
> If I understand correctly when an interrupt controller node wasn't speficied in
> the parent this was unwinding until it found one...
Correct if not specified in each PRU node, and ends up finding the complete
wrong interrupt controller (GIC) as it walks up the tree.
>
>> + parent = of_get_parent(dev_of_node(pru->dev));
>> + if (!parent)
>> + return -ENODEV;
>> +
>> + irq_parent = of_get_child_by_name(parent, "interrupt-controller");
>> + of_node_put(parent);
>> if (!irq_parent) {
>> kfree(pru->mapped_irq);
>> return -ENODEV;
>> @@ -337,11 +344,13 @@ static int pru_handle_intrmap(struct rproc *rproc)
>> goto map_fail;
>> }
>> }
>> + of_node_put(irq_parent);
>>
>> return ret;
>>
>> map_fail:
>> pru_dispose_irq_mapping(pru);
>> + of_node_put(irq_parent);
>
> Reviewed-by: Mathieu Poirier <mathieu.poirier@xxxxxxxxxx>
Thanks,
Suman
>
>>
>> return ret;
>> }
>> --
>> 2.30.1
>>
