Based on linux-gpio discussion [1], it is best practice to make the gpio-line-names unique. Generic names like "[ethernet]" are replaced with the name of the unique signal on the AM3358 SoC ball corresponding to the gpio line. "[NC]" is also renamed to the standard "NC" name to represent "not connected". [1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/ Signed-off-by: Drew Fustini <drew@xxxxxxxxxxxxxxx> --- arch/arm/boot/dts/am335x-pocketbeagle.dts | 140 +++++++++++----------- 1 file changed, 70 insertions(+), 70 deletions(-) diff --git a/arch/arm/boot/dts/am335x-pocketbeagle.dts b/arch/arm/boot/dts/am335x-pocketbeagle.dts index d526c5941c9b..209cdd17dc1e 100644 --- a/arch/arm/boot/dts/am335x-pocketbeagle.dts +++ b/arch/arm/boot/dts/am335x-pocketbeagle.dts @@ -61,51 +61,51 @@ vmmcsd_fixed: fixedregulator0 { &gpio0 { gpio-line-names = - "[NC]", - "[NC]", + "NC", + "NC", "P1.08 [SPI0_CLK]", "P1.10 [SPI0_MISO]", "P1.12 [SPI0_MOSI]", "P1.06 [SPI0_CS]", "[MMC0_CD]", "P2.29 [SPI1_CLK]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", + "[SYSBOOT 12]", + "[SYSBOOT 13]", + "[SYSBOOT 14]", + "[SYSBOOT 15]", "P1.26 [I2C2_SDA]", "P1.28 [I2C2_SCL]", "P2.11 [I2C1_SDA]", "P2.09 [I2C1_SCL]", - "[NC]", - "[NC]", - "[NC]", + "NC", + "NC", + "NC", "P2.31 [SPI1_CS]", "P1.20 [PRU0.16]", - "[NC]", - "[NC]", + "NC", + "NC", "P2.03", - "[NC]", - "[NC]", + "NC", + "NC", "P1.34", "P2.19", - "[NC]", - "[NC]", + "NC", + "NC", "P2.05 [UART4_RX]", "P2.07 [UART4_TX]"; }; &gpio1 { gpio-line-names = - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", "P2.25 [SPI1_MOSI]", "P1.32 [UART0_RX]", "P1.30 [UART0_TX]", @@ -113,10 +113,10 @@ &gpio1 { "P2.33", "P2.22", "P2.18", - "[NC]", - "[NC]", + "NC", + "NC", "P2.01 [PWM1A]", - "[NC]", + "NC", "P2.10", "[USR LED 0]", "[USR LED 1]", @@ -126,35 +126,35 @@ &gpio1 { "P2.04", "P2.02", "P2.08", - "[NC]", - "[NC]", - "[NC]"; + "NC", + "NC", + "NC"; }; &gpio2 { gpio-line-names = "P2.20", "P2.17", - "[NC]", - "[NC]", - "[NC]", + "NC", + "NC", + "NC", "[EEPROM_WP]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", + "[SYSBOOT 0]", + "[SYSBOOT 1]", + "[SYSBOOT 2]", + "[SYSBOOT 3]", + "[SYSBOOT 4]", + "[SYSBOOT 5]", + "[SYSBOOT 6]", + "[SYSBOOT 7]", + "[SYSBOOT 8]", + "[SYSBOOT 9]", + "[SYSBOOT 10]", + "[SYSBOOT 11]", + "NC", + "NC", + "NC", + "NC", "P2.35 [AIN5]", "P1.02 [AIN6]", "P1.35 [PRU1.10]", @@ -169,19 +169,19 @@ &gpio2 { &gpio3 { gpio-line-names = - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", + "NC", + "NC", + "NC", + "NC", + "NC", "[I2C0_SDA]", "[I2C0_SCL]", - "[JTAG]", - "[JTAG]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", + "[JTAG EMU0]", + "[JTAG EMU1]", + "NC", + "NC", + "NC", + "NC", "P1.03 [USB1]", "P1.36 [PWM0A]", "P1.33 [PRU0.1]", @@ -191,16 +191,16 @@ &gpio3 { "P2.34 [PRU0.5]", "P2.28 [PRU0.6]", "P1.29 [PRU0.7]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]"; + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC"; }; &am33xx_pinmux { -- 2.25.1
