On 05/11/2020 20:56, H. Nikolaus Schaller wrote: > >> Am 05.11.2020 um 19:28 schrieb Tomi Valkeinen <tomi.valkeinen@xxxxxx>: >> >> On 05/11/2020 20:14, H. Nikolaus Schaller wrote: >>> >>>> Am 05.11.2020 um 18:36 schrieb Tomi Valkeinen <tomi.valkeinen@xxxxxx>: >>>> >>>> Hi, >>>> >>>> On 05/11/2020 19:15, H. Nikolaus Schaller wrote: >>>> >>>>> Next, I migrated my long waiting mipi_dsi/drm_panel driver conversion for >>>>> the panel of the Pyra handheld (omap 5 based) to compile on 5.10-rc2. And >>>>> I followed the latest existing panel-orisetech-otm8009a.c which uses a >>>>> similar video mode controller and mipi-dsi. >>>>> >>>>> That one seems to be used by arch/arm/boot/dts/stm32f469-disco.dts. >>>>> >>>>> Unfortunately my panel driver is not even loaded by drm/omap so I can't >>>>> debug. Does this set of drm/omap drivers need a modification of the device >>>>> tree? If yes, which one? >>>> >>>> omapdrm doesn't load the panel drivers. If not even your panel's probe is called, then it hints at >>>> DT and/or driver's compatible string issue. The panel's probe should get called even if omapdrm is >>>> not loaded at all. >>> >>> Well, I use the same device tree that loads the old driver... >> >> Yeah, I was mistaken above. With DSI the panel (may be) a child of the DSI host, so it will affect. >> >> Can you give pointers to the panel driver source and relevant dts files? BOE BTL507212-W677L? > > Yes. It is (now) > > drivers/gpu/drm/panel/panel-boe-btl507212-w677l.c > > and > > arch/arm/boot/dts/omap5-letux-cortex15-common.dtsi (for the basic dsi definitions) > arch/arm/boot/dts/pyra-display.dtsi (for the specific display) > > All this is merged by some arch/arm/boot/dts/omap5-letux-cortex15-v5.3+pyra-v5.2.dts I took the driver and make my omap4-sdp dts to use it. It probes for me, but stop after that: [ 119.346374] omapdss_dss 58000000.dss: supply vdda_video not found, using dummy regulator [ 119.358398] DSS: OMAP DSS rev 4.0 [ 119.680053] panel-dsi-cm 58004000.encoder.0: failed to get video timing, using defaults [ 119.695709] panel-dsi-cm 58004000.encoder.0: supply vpnl not found, using dummy regulator [ 119.711242] panel-dsi-cm 58004000.encoder.0: supply vddi not found, using dummy regulator [ 119.769470] panel-btl507212-w677l 58005000.encoder.0: w677l_probe [ 119.779388] panel-btl507212-w677l 58005000.encoder.0: w677l_probe ok [ 119.846679] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops [omapdrm]) [ 119.858673] omapdss_dss 58000000.dss: bound 58004000.encoder (ops dsi_component_ops [omapdrm]) [ 119.882629] omapdss_dss 58000000.dss: bound 58005000.encoder (ops dsi_component_ops [omapdrm]) [ 119.902069] omapdss_dss 58000000.dss: bound 58006000.encoder (ops hdmi4_component_ops [omapdrm]) [ 119.962066] dmm 4e000000.dmm: initialized all PAT entries [ 120.014770] panel-btl507212-w677l 58005000.encoder.0: w677l_get_modes I didn't debug yet where it's hanging. So you're not even getting the probe? Tomi -- Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki