[PATCH v2] ARM: dts: document pinctrl-single,pins when #pinctrl-cells = 2

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Document the values in pinctrl-single,pins when #pinctrl-cells = <2>

Fixes: 27c90e5e48d0 ("ARM: dts: am33xx-l4: change #pinctrl-cells from 1 to 2")
Reported-by: Trent Piepho <tpiepho@xxxxxxxxx>
Link: https://lore.kernel.org/linux-omap/3139716.CMS8C0sQ7x@zen.local/
Signed-off-by: Drew Fustini <drew@xxxxxxxxxxxxxxx>
---
v2 change:
- rephrase to make it clear that the pin conf value and pin mux value
  are OR'd together with #pinctrl-cells = <2>


 .../bindings/pinctrl/pinctrl-single.txt       | 21 ++++++++++++-------
 1 file changed, 14 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
index e705acd3612c..f903eb4471f8 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
@@ -94,16 +94,23 @@ pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
 specified in the pinctrl-bindings.txt document in this directory.
 
 The pin configuration nodes for pinctrl-single are specified as pinctrl
-register offset and value pairs using pinctrl-single,pins. Only the bits
-specified in pinctrl-single,function-mask are updated. For example, setting
-a pin for a device could be done with:
+register offset and values using pinctrl-single,pins. Only the bits specified
+in pinctrl-single,function-mask are updated.
+
+When #pinctrl-cells = 1, then setting a pin for a device could be done with:
 
 	pinctrl-single,pins = <0xdc 0x118>;
 
-Where 0xdc is the offset from the pinctrl register base address for the
-device pinctrl register, and 0x118 contains the desired value of the
-pinctrl register. See the device example and static board pins example
-below for more information.
+Where 0xdc is the offset from the pinctrl register base address for the device
+pinctrl register, and 0x118 contains the desired value of the pinctrl register.
+
+When #pinctrl-cells = 2, then setting a pin for a device could be done with:
+
+	pinctrl-single,pins = <0xdc 0x30 0x07>;
+
+Where 0x30 is the pin configuration value and 0x07 is the pin mux mode value.
+These two values are OR'd together to produce the value stored at offset 0xdc.
+See the device example and static board pins example below for more information.
 
 In case when one register changes more than one pin's mux the
 pinctrl-single,bits need to be used which takes three parameters:
-- 
2.25.1




[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux