Convert panel-dsi-cm bindings to YAML and add
missing properties while at it.
Signed-off-by: Sebastian Reichel <sebastian.reichel@xxxxxxxxxxxxx>
---
.../bindings/display/panel/panel-dsi-cm.txt | 31 ------
.../bindings/display/panel/panel-dsi-cm.yaml | 97 +++++++++++++++++++
2 files changed, 97 insertions(+), 31 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/panel/panel-dsi-cm.txt
create mode 100644 Documentation/devicetree/bindings/display/panel/panel-dsi-cm.yaml
diff --git a/Documentation/devicetree/bindings/display/panel/panel-dsi-cm.txt b/Documentation/devicetree/bindings/display/panel/panel-dsi-cm.txt
deleted file mode 100644
index f92d5c9adfc5..000000000000
--- a/Documentation/devicetree/bindings/display/panel/panel-dsi-cm.txt
+++ /dev/null
@@ -1,31 +0,0 @@
-Generic MIPI DSI Command Mode Panel
-===================================
-
-Required properties:
-- compatible: "panel-dsi-cm"
-- reg: DSI channel number
-
-Optional properties:
-- label: a symbolic name for the panel
-- reset-gpios: panel reset gpio
-- te-gpios: panel TE gpio
-
-Required nodes:
-- Video port for DSI input
-
-Example
--------
-
-lcd0: panel@0 {
- compatible = "tpo,taal", "panel-dsi-cm";
- label = "lcd0";
- reg = <0>;
-
- reset-gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>;
-
- port {
- lcd0_in: endpoint {
- remote-endpoint = <&dsi1_out_ep>;
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/display/panel/panel-dsi-cm.yaml b/Documentation/devicetree/bindings/display/panel/panel-dsi-cm.yaml
new file mode 100644
index 000000000000..ca61171ae145
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/panel-dsi-cm.yaml
@@ -0,0 +1,97 @@
+# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/panel-dsi-cm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: DSI command mode panels
+
+maintainers:
+ - Tomi Valkeinen <tomi.valkeinen@xxxxxx>
+ - Sebastian Reichel <sre@xxxxxxxxxx>
+
+description: |
+ This binding file is a collection of the DSI panels that
+ are usually driven in command mode. If no backlight is
+ referenced via the optional backlight property, the DSI
+ panel is assumed to have native backlight support.
+ The panel may use an OF graph binding for the association
+ to the display, or it may be a direct child node of the
+ display.
+
+allOf:
+ - $ref: panel-common.yaml#
+
+properties:
+
+ compatible:
+ enum:
+ # compatible must be listed in alphabetical order, ordered by compatible.
+ # The description in the comment is mandatory for each compatible.
+ - motorola,droid4-panel, panel-dsi-cm
+ - nokia,himalaya, panel-dsi-cm
+ - tpo,taal, panel-dsi-cm
+
+ reg:
+ maxItems: 1
+ description: DSI virtual channel
+
+ te-gpios:
+ maxItems: 1
+ description:
+ Specifier for a GPIO connected to the panel TE (tearing event) signal.
+ The GPIO informs the system, that data should be sent to the display
+ on rising edges of the GPIO to avoid (or reduce) tearing effects.
+ Falling edge can be supported by inverting the GPIO specifier polarity
+ flag.
+
+ vddi-supply:
+ description:
+ Display panels require power to be supplied. While several panels need
+ more than one power supply with panel-specific constraints governing the
+ order and timings of the power supplies, in many cases a single power
+ supply is sufficient, either because the panel has a single power rail, or
+ because all its power rails can be driven by the same supply. In that case
+ the vddi-supply property specifies the supply powering the panel as a
+ phandle to a regulator.
+
+ vpnl-supply:
+ description:
+ When the display panel needs a second power supply, this property can be
+ used in addition to vddi-supply. Both supplies will be enabled at the
+ same time before the panel is being accessed.
+
+ width-mm: true
+ height-mm: true
+ label: true
+ rotation: true
+ panel-timing: true
+ port: true
+ reset-gpios: true
+ backlight: true
+
+additionalProperties: false
+
+required:
+ - compatible
+ - port
+ - reg
+
+examples:
+ - |
+ dsi1@12345678 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ panel@0 {
+ compatible = "tpo,taal", "panel-dsi-cm";
+ label = "lcd0";
+ reg = <0>;
+ reset-gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>;
+
+ port {
+ panel: endpoint {
+ remote-endpoint = <&dsi1_out_ep>;
+ };
+ };
+ };
+ };
--
2.25.0
