This patch causes the OMAP uarts to honor the sysfs power/wakeup file
for IOPAD wakeups. Before the OMAP was always woken up from off mode
on a rs232 signal change. This patch also creates a different
platform device for each serial port so that the wakeup properties can
be control per port.
By default, IOPAD wakeups are enabled for each UART. To disable,
# echo disabled > /sys/devices/platform/serial8250.0/power/wakeup
Where serial8250.0 can be replaced by .1, or .2 to control the other
ports.
Original idea and original patch from Russ Dill <russ.dill@xxxxxxxxx>
Cc: Russ Dill <russ.dill@xxxxxxxxx>
Signed-off-by: Kevin Hilman <khilman@xxxxxxxxxxxxxxxxxxx>
---
arch/arm/mach-omap2/serial.c | 174 ++++++++++++++++++++++++++++--------------
1 files changed, 116 insertions(+), 58 deletions(-)
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index 5352d05..6f35a7e 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -54,6 +54,7 @@ struct omap_uart_state {
struct plat_serial8250_port *p;
struct list_head node;
+ struct platform_device pdev;
#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
int context_valid;
@@ -68,10 +69,9 @@ struct omap_uart_state {
#endif
};
-static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS];
static LIST_HEAD(uart_list);
-static struct plat_serial8250_port serial_platform_data[] = {
+static struct plat_serial8250_port serial_platform_data0[] = {
{
.membase = IO_ADDRESS(OMAP_UART1_BASE),
.mapbase = OMAP_UART1_BASE,
@@ -81,6 +81,12 @@ static struct plat_serial8250_port serial_platform_data[] = {
.regshift = 2,
.uartclk = OMAP24XX_BASE_BAUD * 16,
}, {
+ .flags = 0
+ }
+};
+
+static struct plat_serial8250_port serial_platform_data1[] = {
+ {
.membase = IO_ADDRESS(OMAP_UART2_BASE),
.mapbase = OMAP_UART2_BASE,
.irq = 73,
@@ -89,6 +95,12 @@ static struct plat_serial8250_port serial_platform_data[] = {
.regshift = 2,
.uartclk = OMAP24XX_BASE_BAUD * 16,
}, {
+ .flags = 0
+ }
+};
+
+static struct plat_serial8250_port serial_platform_data2[] = {
+ {
.membase = IO_ADDRESS(OMAP_UART3_BASE),
.mapbase = OMAP_UART3_BASE,
.irq = 74,
@@ -217,6 +229,40 @@ static inline void omap_uart_disable_clocks(struct omap_uart_state *uart)
clk_disable(uart->fck);
}
+static void omap_uart_enable_wakeup(struct omap_uart_state *uart)
+{
+ /* Set wake-enable bit */
+ if (uart->wk_en && uart->wk_mask) {
+ u32 v = __raw_readl(uart->wk_en);
+ v |= uart->wk_mask;
+ __raw_writel(v, uart->wk_en);
+ }
+
+ /* Ensure IOPAD wake-enables are set */
+ if (cpu_is_omap34xx() && uart->padconf) {
+ u16 v = omap_ctrl_readw(uart->padconf);
+ v |= OMAP3_PADCONF_WAKEUPENABLE0;
+ omap_ctrl_writew(v, uart->padconf);
+ }
+}
+
+static void omap_uart_disable_wakeup(struct omap_uart_state *uart)
+{
+ /* Clear wake-enable bit */
+ if (uart->wk_en && uart->wk_mask) {
+ u32 v = __raw_readl(uart->wk_en);
+ v &= ~uart->wk_mask;
+ __raw_writel(v, uart->wk_en);
+ }
+
+ /* Ensure IOPAD wake-enables are cleared */
+ if (cpu_is_omap34xx() && uart->padconf) {
+ u16 v = omap_ctrl_readw(uart->padconf);
+ v &= ~OMAP3_PADCONF_WAKEUPENABLE0;
+ omap_ctrl_writew(v, uart->padconf);
+ }
+}
+
static void omap_uart_smart_idle_enable(struct omap_uart_state *uart,
int enable)
{
@@ -246,6 +292,11 @@ static void omap_uart_block_sleep(struct omap_uart_state *uart)
static void omap_uart_allow_sleep(struct omap_uart_state *uart)
{
+ if (device_may_wakeup(&uart->pdev.dev))
+ omap_uart_enable_wakeup(uart);
+ else
+ omap_uart_disable_wakeup(uart);
+
if (!uart->clocked)
return;
@@ -292,7 +343,6 @@ void omap_uart_resume_idle(int num)
/* Check for normal UART wakeup */
if (__raw_readl(uart->wk_st) & uart->wk_mask)
omap_uart_block_sleep(uart);
-
return;
}
}
@@ -346,16 +396,13 @@ static irqreturn_t omap_uart_interrupt(int irq, void *dev_id)
return IRQ_NONE;
}
-static u32 sleep_timeout = DEFAULT_TIMEOUT;
-
static void omap_uart_idle_init(struct omap_uart_state *uart)
{
- u32 v;
struct plat_serial8250_port *p = uart->p;
int ret;
uart->can_sleep = 0;
- uart->timeout = sleep_timeout;
+ uart->timeout = DEFAULT_TIMEOUT;
setup_timer(&uart->timer, omap_uart_idle_timer,
(unsigned long) uart);
mod_timer(&uart->timer, jiffies + uart->timeout);
@@ -413,22 +460,6 @@ static void omap_uart_idle_init(struct omap_uart_state *uart)
uart->padconf = 0;
}
- /* Set wake-enable bit */
- if (uart->wk_en && uart->wk_mask) {
- v = __raw_readl(uart->wk_en);
- v |= uart->wk_mask;
- __raw_writel(v, uart->wk_en);
- }
-
- /* Ensure IOPAD wake-enables are set */
- if (cpu_is_omap34xx() && uart->padconf) {
- u16 v;
-
- v = omap_ctrl_readw(uart->padconf);
- v |= OMAP3_PADCONF_WAKEUPENABLE0;
- omap_ctrl_writew(v, uart->padconf);
- }
-
p->flags |= UPF_SHARE_IRQ;
ret = request_irq(p->irq, omap_uart_interrupt, IRQF_SHARED,
"serial idle", (void *)uart);
@@ -449,54 +480,81 @@ void omap_uart_enable_irqs(int enable)
}
}
-static ssize_t sleep_timeout_show(struct kobject *kobj,
- struct kobj_attribute *attr,
+static ssize_t sleep_timeout_show(struct device *dev,
+ struct device_attribute *attr,
char *buf)
{
- return sprintf(buf, "%u\n", sleep_timeout / HZ);
+ struct platform_device *pdev = container_of(dev,
+ struct platform_device, dev);
+ struct omap_uart_state *uart = container_of(pdev,
+ struct omap_uart_state, pdev);
+
+ return sprintf(buf, "%u\n", uart->timeout / HZ);
}
-static ssize_t sleep_timeout_store(struct kobject *kobj,
- struct kobj_attribute *attr,
+static ssize_t sleep_timeout_store(struct device *dev,
+ struct device_attribute *attr,
const char *buf, size_t n)
{
- struct omap_uart_state *uart;
+ struct platform_device *pdev = container_of(dev,
+ struct platform_device, dev);
+ struct omap_uart_state *uart = container_of(pdev,
+ struct omap_uart_state, pdev);
unsigned int value;
if (sscanf(buf, "%u", &value) != 1) {
printk(KERN_ERR "sleep_timeout_store: Invalid value\n");
return -EINVAL;
}
- sleep_timeout = value * HZ;
- list_for_each_entry(uart, &uart_list, node) {
- uart->timeout = sleep_timeout;
- if (uart->timeout)
- mod_timer(&uart->timer, jiffies + uart->timeout);
- else
- /* A zero value means disable timeout feature */
- omap_uart_block_sleep(uart);
- }
+
+ uart->timeout = value * HZ;
+ if (uart->timeout)
+ mod_timer(&uart->timer, jiffies + uart->timeout);
+ else
+ /* A zero value means disable timeout feature */
+ omap_uart_block_sleep(uart);
+
return n;
}
-static struct kobj_attribute sleep_timeout_attr =
- __ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store);
-
+DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store);
+#define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr))
#else
static inline void omap_uart_idle_init(struct omap_uart_state *uart) {}
+#define DEV_CREATE_FILE(dev, attr)
#endif /* CONFIG_PM */
-static struct platform_device serial_device = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev = {
- .platform_data = serial_platform_data,
+static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS] = {
+ {
+ .pdev = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = serial_platform_data0,
+ },
+ },
+ }, {
+ .pdev = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM1,
+ .dev = {
+ .platform_data = serial_platform_data1,
+ },
+ },
+ }, {
+ .pdev = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM2,
+ .dev = {
+ .platform_data = serial_platform_data2,
+ },
+ },
},
};
void __init omap_serial_init(void)
{
- int i, err;
+ int i;
const struct omap_uart_config *info;
char name[16];
@@ -512,8 +570,10 @@ void __init omap_serial_init(void)
return;
for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
- struct plat_serial8250_port *p = serial_platform_data + i;
struct omap_uart_state *uart = &omap_uart[i];
+ struct platform_device *pdev = &uart->pdev;
+ struct device *dev = &pdev->dev;
+ struct plat_serial8250_port *p = dev->platform_data;
if (!(info->enabled_uarts & (1 << i))) {
p->membase = NULL;
@@ -549,15 +609,13 @@ void __init omap_serial_init(void)
omap_uart_enable_clocks(uart);
omap_uart_reset(uart);
omap_uart_idle_init(uart);
- }
-
- err = platform_device_register(&serial_device);
-
-#ifdef CONFIG_PM
- if (!err)
- err = sysfs_create_file(&serial_device.dev.kobj,
- &sleep_timeout_attr.attr);
-#endif
+ if (WARN_ON(platform_device_register(pdev)))
+ continue;
+ if ((cpu_is_omap34xx() && uart->padconf) ||
+ (uart->wk_en && uart->wk_mask)) {
+ device_init_wakeup(dev, true);
+ DEV_CREATE_FILE(dev, &dev_attr_sleep_timeout);
+ }
+ }
}
-
--
1.6.3.2
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
