Re: [PATCH 1/1] ARM: dts: am5729: beaglebone-ai: adding device tree

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 19/11/2019 22:28, Caleb Robey wrote:
From: Jason Kridner <jdk@xxxxxx>

BeagleBoard.org BeagleBone AI is an open source hardware single
board computer based on the Texas Instruments AM5729 SoC featuring
dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital
signal processor (DSP), quad-core embedded vision engine (EVE),
Arm Cortex-M4 processors, dual programmable realtime unit
industrial control subsystems and more. The board features 1GB
DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash,
1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion
headers.

For more information, refer to:
https://beaglebone.ai



This patch introduces the BeagleBone AI device tree.

Note that the device use the "ti,tpd12s016" component which is
software compatible with "ti,tpd12s015". Thus we only use the
latter driver.

Signed-off-by: Jason Kridner <jdk@xxxxxx>
Signed-off-by: Caleb Robey <c-robey@xxxxxx>
Cc: Robert Nelson <robertcnelson@xxxxxxxxx>

---
  arch/arm/boot/dts/Makefile                |   1 +
  arch/arm/boot/dts/am5729-beagleboneai.dts | 782 ++++++++++++++++++++++
  2 files changed, 783 insertions(+)
  create mode 100644 arch/arm/boot/dts/am5729-beagleboneai.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b21b3a64641a..b1154dbda73c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile

[..]

+
+&uart1 {
+	status = "okay";
+};
+
+&davinci_mdio {
+	reset-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+	reset-delay-us = <2>;
+
+	phy0: ethernet-phy@1 {
+		reg = <4>;
+		compatible = "ethernet-phy-id004d.d072",
+			"ethernet-phy-ieee802.3-c22";

Pls, do not ignore my comments.

Above compatible should not be required.

+		eee-broken-100tx;
+		eee-broken-1000t;
+	};
+};
+
+&mac {
+	slaves = <1>;
+	status = "okay";
+};

Pls, move cpsw node here

+
+&ocp {
+	pruss1_shmem: pruss_shmem@4b200000 {
+		status = "okay";
+		compatible = "ti,pruss-shmem";
+		reg = <0x4b200000 0x020000>;
+	};
+

[..]

+
+&cpsw_emac0 {
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii";
+};

Move it up, pls.

--
Best regards,
grygorii



[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux