> As maintainer of the TDA998x driver, I know what the TDA998x is > capable of, I already have the datasheets, and I know the binding > document. > What I'm asking about is about the specifics of your board's > implementation and why you've written what you have in your DT > file. You haven't answered my specific questions either. I am sorry I was unclear. My apologies. Here is the wiring between LCD controller and the framer: LCD[11:15] ====> VPA[3:7] LCD[5:10] ====> VPB[2:7] LCD[0:4] ====> VPC[3:7] Here is the schematic: https://octavosystems.com/docs/osd3358-sm-red-schematics-pdf/ And yes, the colors will come out wrong for the 24 bit for the configuration set. See "blue-and-red-wiring" in tilcdc bindings: https://www.kernel.org/doc/Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt AM335x errata providing wiring info for 24 bit mode: http://www.ti.com/lit/er/sprz360i/sprz360i.pdf We used the same interface design as the BeagleBone Black: https://github.com/torvalds/linux/blob/master/arch/arm/boot/dts/am335x-boneblack-common.dtsi Hope this is helpful. Thanks, Neeraj On Tue, Jul 10, 2018 at 3:26 AM Russell King - ARM Linux <linux@xxxxxxxxxxxxxxx> wrote: > > On Mon, Jul 09, 2018 at 02:45:17PM -0500, Neeraj Kumar Reddy Dantu wrote: > > > This should not be "tda19988" as the node name - DT requires generic > > > names, like "hdmi-encoder". > > > > Thanks.Will fix in v3 > > > > > Can you set 24-bit RGB mode with the above configuration - presumably > > > the colours will come out wrong? > > > Exactly what is the wiring between the lcdc and tda998x? > > > > You can set mapping for lcd interface between pins with video-ports. See > > TDA19988 datasheet, Table 4: > > https://media.digikey.com/pdf/Data%20Sheets/NXP%20PDFs/TDA19988_DS_21_july_2011.pdf > > . > > The property is optional and not used in the board. DT bindings: > > https://www.kernel.org/doc/Documentation/devicetree/bindings/display/bridge/tda998x.txt > > > > This board uses 15 pin RGB565 interface. > > As maintainer of the TDA998x driver, I know what the TDA998x is > capable of, I already have the datasheets, and I know the binding > document. > > What I'm asking about is about the specifics of your board's > implementation and why you've written what you have in your DT > file. You haven't answered my specific questions either. > > > > > Regards, > > Neeraj > > > > On Mon, Jul 9, 2018 at 6:43 AM Russell King - ARM Linux < > > linux@xxxxxxxxxxxxxxx> wrote: > > > > > On Fri, Jul 06, 2018 at 08:00:51PM +0000, Neeraj Dantu wrote: > > > > +&lcdc { > > > > + status = "okay"; > > > > + > > > > + /* If you want to get 24 bit RGB and 16 BGR mode instead of > > > > + * current 16 bit RGB and 24 BGR modes, set the propety > > > > + * below to "crossed" and uncomment the video-ports -property > > > > + * in tda19988 node. > > > > + */ > > > > + blue-and-red-wiring = "straight"; > > > ... > > > > +&i2c0 { > > > > + tda19988: tda19988 { > > > > > > This should not be "tda19988" as the node name - DT requires generic > > > names, like "hdmi-encoder". > > > > > > ... > > > > + /* Convert 24bit BGR to RGB, e.g. cross red and blue > > > wiring */ > > > > + /* video-ports = <0x234501>; */ > > > > > > Please explain more what's going on here. > > > > > > Can you set 24-bit RGB mode with the above configuration - presumably > > > the colours will come out wrong? > > > > > > Exactly what is the wiring between the lcdc and tda998x? > > > > > > -- > > > RMK's Patch system: http://www.armlinux.org.uk/developer/patches/ > > > FTTC broadband for 0.8mile line in suburbia: sync at 13.8Mbps down 630kbps > > > up > > > According to speedtest.net: 13Mbps down 490kbps up > > > > > -- > RMK's Patch system: http://www.armlinux.org.uk/developer/patches/ > FTTC broadband for 0.8mile line in suburbia: sync at 13.8Mbps down 630kbps up > According to speedtest.net: 13Mbps down 490kbps up -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
