Hi Tony,
On 01/19/2018 03:33 PM, Tony Lindgren wrote:
> * Suman Anna <s-anna@xxxxxx> [180119 20:23]:
>> On 01/16/2018 05:22 PM, Tony Lindgren wrote:
>>> The RSTST registers mostly tell the device internal reset reason
>>> like watchdog reset for an accelerator. I'm not sure how the
>>> API for those would look like, do you have some ideas?
>>
>> There are multiple RSTST registers, each of which with different bits. .
>> The PRM_RSTST is the one where you can catch the reset reasons (along
>> with few others), but otherwise most of the other IP-specific RSTST
>> registers capture the local reset status. The RSTST behavior is somewhat
>> similar to how the softreset status is tracked on each IP's SYSC/SYSS
>> registers. It does tell the reset status for some software triggered
>> resets in RSTCTRL, and can have additional bits as well for some PRCM
>> triggered h/w resets (like RETention reset).
>
> Hmm so are you using these "additional" software status bits?
I am only using the ones associated with the respective software control
bits. For example, DRA7 DSP RSTST has two additional bits associated
with Emulation, but there are no corresponding bits in RSTCTRL.
Similarly, PRM_RSTST has lot more bits other than the global warm and
cold reset trigger sources from s/w. Note that the current reboot code
is directly using the low-level PRM api omap_prm_reset_system(), which
actually acts on the PRM_RSTCTRL. But I see these are usually handled in
drivers/power/reset.
>
> If the other bits don't matter, and the RSTCTRL reset bit has
> a matching RSTST bit, then we could just read that bit back
> in reset_simple_status and have a separate compatible value
> for those like "ti,rstctrl-rstst".
We will have to cross-check all the RSTST and RSTCTRL instances across
all the AMxx and OMAPxx SoCs to see if the bit positions are exactly
matched up, I believe there are couple of exceptions (either bit
positions or register offsets). This is one of the reasons we used
separate fields in the reset-ti-syscon driver :)
>
>>> Hmm, aren't you currently just reading the RSTST registers
>>> directly for remoteproc etc?
>>
>> Nope, all the PRCM related registers are hidden away underneath the
>> hwmod layer, so the only code that I use is pm_runtime_{get/put}_sync()
>> directly and omap_device_{assert/deassert}_reset() through pdata-quirks.
>> Take a look in drivers/iommu/omap-iommu.c and
>> arch/arm/mach-omap2/pdata-quirks.c (functional in mainline for OMAP4 and
>> OMAP5 DSP/IPU MMUs).
>
> OK, sorry I was thinking of the CLKCTRL IDLEST that are directly
> accessed :)
I am not sure if everyone is able to access these normally atleast
before with hwmod code. I did use these in the TI downstream kernel
directly by having an explicit register reference to it in DT, which I
consider a workaround!!
>
>>> And then we also have the CONTEXT register that tells if module
>>> context was lost during idle :) The API for that could simply be
>>> bool device_context_lost(struct device *dev) to describe that
>>> kind of reset. Or it could maybe also use reset_control_status()
>>> that returns -ECONNRESET? But then what resets the context lost
>>> state as we don't need to reset the device?
>>
>> I am not sure why the CONTEXT register belongs to the same discussion as
>> the reset registers. In any case, I don't think any of the current code
>> relies on this (other than incrementing the debug counters).
>
> Well they are in the same PRM instance, and behave the same way
> as RSTST :) They are like interrupt status registers where you can
> read the state and write to clear it. I wonder if we do really have
> a proper PRM interrupt for these too, Tero?
They are just status registers, I don't see any interrupts associated
with them. Where are the PWRSTCTRL and PWRSTST registers being managed -
they are also part of the same PRM instances.
>
>> The OMAP IOMMU would be a better test given that there's no in-kernel
>> sgx module and we are not sure if the out-of-tree driver is functional
>> with these changes.
>>
>> I have some unit-test code at
>> https://github.com/sumananna/omap-test-iommu.git
>>
>> You would need to add a test node to DTS with reference to the MMU you
>> want to test.
>
> OK let's do some tests on that, I'll take a look at doing a dts
> file over next few weeks.
You can look up the patches folder in the above repo, there are some
example nodes there already, they are rather straight-forward.
>
>> If we are exposing all the other registers directly to client drivers,
>> then the client drivers can use the reset API directly. But if other
>> registers are hidden away underneath various frameworks, then we have
>> some sequencing issues.
>
> Right that needs to be checked. For ti-sysc driver we only need to
> care about the rests that are needed to read and configure the
> interconnect target module. The rest can be handled directly by
> the child device drivers hopefully.
>
>> Tero had done a series sometime back using notifiers to take care of
>> these sequencing steps, but that was deferred pending the other hwmod
>> cleanup. Last reference that touches it is here,
>> https://marc.info/?l=linux-omap&m=147279610902646&w=2
>
> Yeah the resets can all be device driver(s) now that we have the
> clkctrl clocks usable and should have ti-sysc usable for v4.17.
Yeah ok, hopefully Tero can look into this more now that the clkctrl is
mostly wrapped up.
regards
Suman
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
