The newly added OMAP35xx Torpedo does not have a WiFi option, so
this patch moves the WL1283 binding and pin muxing to the
logicpd-torpedo-37xx-devkit since it's only applicable on that SOM
Signed-off-by: Adam Ford <aford173@xxxxxxxxx>
diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
index b5404f0..234afd6 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
+++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
@@ -14,4 +14,64 @@
/ {
model = "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit";
compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3";
+
+ wl12xx_vmmc: wl12xx_vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1271";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio5 29 0>; /* gpio157 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ vin-supply = <&vmmc2>;
+ };
+};
+
+/*
+ * Only found on the wireless SOM. For the SOM without wireless, the pins for
+ * MMC3 can be routed with jumpers to the second MMC slot on the devkit and
+ * gpio157 is not connected. So this should be OK to keep common for now,
+ * probably device tree overlays is the way to go with the various SOM and
+ * jumpering combinations for the long run.
+ */
+&mmc3 {
+ interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
+ pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>;
+ pinctrl-names = "default";
+ vmmc-supply = <&wl12xx_vmmc>;
+ non-removable;
+ bus-width = <4>;
+ cap-power-off-card;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1283";
+ reg = <2>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
+ ref-clock-frequency = <26000000>;
+ tcxo-clock-frequency = <26000000>;
+ };
+};
+
+&omap3_pmx_core {
+ mmc3_pins: pinmux_mm3_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
+ OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
+ OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
+ OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
+ OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
+ OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */
+ >;
+ };
+};
+
+&omap3_pmx_core2 {
+ mmc3_core2_pins: pinmux_mmc3_core2_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */
+ OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */
+ >;
+ };
};
diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
index 6d89736..aad0cd5 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
+++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
@@ -30,17 +30,6 @@
linux,default-trigger = "none";
};
};
-
- wl12xx_vmmc: wl12xx_vmmc {
- compatible = "regulator-fixed";
- regulator-name = "vwl1271";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- gpio = <&gpio5 29 0>; /* gpio157 */
- startup-delay-us = <70000>;
- enable-active-high;
- vin-supply = <&vmmc2>;
- };
};
&gpmc {
@@ -131,44 +120,7 @@
};
};
-/*
- * Only found on the wireless SOM. For the SOM without wireless, the pins for
- * MMC3 can be routed with jumpers to the second MMC slot on the devkit and
- * gpio157 is not connected. So this should be OK to keep common for now,
- * probably device tree overlays is the way to go with the various SOM and
- * jumpering combinations for the long run.
- */
-&mmc3 {
- interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
- pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>;
- pinctrl-names = "default";
- vmmc-supply = <&wl12xx_vmmc>;
- non-removable;
- bus-width = <4>;
- cap-power-off-card;
- #address-cells = <1>;
- #size-cells = <0>;
- wlcore: wlcore@2 {
- compatible = "ti,wl1283";
- reg = <2>;
- interrupt-parent = <&gpio5>;
- interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
- ref-clock-frequency = <26000000>;
- tcxo-clock-frequency = <26000000>;
- };
-};
-
&omap3_pmx_core {
- mmc3_pins: pinmux_mm3_pins {
- pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
- OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
- OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
- OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
- OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
- OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */
- >;
- };
mcbsp2_pins: pinmux_mcbsp2_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */
@@ -224,15 +176,6 @@
pinctrl-0 = <&mcspi1_pins>;
};
-&omap3_pmx_core2 {
- mmc3_core2_pins: pinmux_mmc3_core2_pins {
- pinctrl-single,pins = <
- OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */
- OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */
- >;
- };
-};
-
#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
