Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra7-evm.
Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx>
---
arch/arm/boot/dts/dra7-evm.dts | 22 ++++++++++++++++++----
1 file changed, 18 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index e4c4037e6314..e74feb7ed53c 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -8,6 +8,7 @@
/dts-v1/;
#include "dra74x.dtsi"
+#include "dra74x-mmc-iodelay.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clk/ti-dra7-atl.h>
#include <dt-bindings/input/input.h>
@@ -443,8 +444,6 @@
&mmc1 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_default>;
vmmc-supply = <&evm_3v3_sd>;
vqmmc-supply = <&ldo1_reg>;
bus-width = <4>;
@@ -453,14 +452,29 @@
* is always hardwired.
*/
cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104";
+ pinctrl-0 = <&mmc1_pins_default>;
+ pinctrl-1 = <&mmc1_pins_hs>;
+ pinctrl-2 = <&mmc1_pins_sdr12>;
+ pinctrl-3 = <&mmc1_pins_sdr25>;
+ pinctrl-4 = <&mmc1_pins_sdr50>;
+ pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev11_conf>;
+ pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>;
+ pinctrl-7 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>;
+ pinctrl-8 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
};
&mmc2 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_default>;
vmmc-supply = <&evm_1v8_sw>;
bus-width = <8>;
+ pinctrl-names = "default", "hs", "ddr_1_8v-rev11", "ddr_1_8v", "hs200_1_8v-rev11", "hs200_1_8v";
+ pinctrl-0 = <&mmc2_pins_default>;
+ pinctrl-1 = <&mmc2_pins_hs>;
+ pinctrl-2 = <&mmc2_pins_ddr_1_8v_rev11 &mmc2_iodelay_ddr_1_8v_rev11_conf>;
+ pinctrl-3 = <&mmc2_pins_ddr_rev20>;
+ pinctrl-4 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev11_conf>;
+ pinctrl-5 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>;
};
&cpu0 {
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
