Looks like nobody bothered to configure USB host for 37xx-evm
when we converted things to device tree, so let's add it. This
is similar to beagleboard configuration with few extra quirks
to configure the port. And as with beagleboard, OHCI won't work
because there is no USB LS/FS PHY. A HS USB hub is needed to use
devices like keyboard and mice.
Cc: Roger Quadros <rogerq@xxxxxx>
Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
---
Changes since v1:
- Claim phy pins for hsusb2_phy as suggested by Rogeq Quadros
---
arch/arm/boot/dts/omap3-evm-37xx.dts | 102 ++++++++++++++++++++++++++++++++
arch/arm/boot/dts/omap3-evm-common.dtsi | 33 +++++++++++
2 files changed, 135 insertions(+)
diff --git a/arch/arm/boot/dts/omap3-evm-37xx.dts b/arch/arm/boot/dts/omap3-evm-37xx.dts
--- a/arch/arm/boot/dts/omap3-evm-37xx.dts
+++ b/arch/arm/boot/dts/omap3-evm-37xx.dts
@@ -34,7 +34,15 @@
>;
};
+&hsusb2_phy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ehci_phy_pins>;
+};
+
&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <&on_board_gpio_61 &hsusb2_pins>;
+
dss_dpi_pins1: pinmux_dss_dpi_pins2 {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
@@ -98,6 +106,37 @@
>;
};
+ /* Devices are routed with gpmc_nbe1.gpio_61 to on-board devices */
+ on_board_gpio_61: pinmux_ehci_port_select_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4)
+ >;
+ };
+
+ /* Used by OHCI and EHCI. OHCI won't work without external phy */
+ hsusb2_pins: pinmux_hsusb2_pins {
+ pinctrl-single,pins = <
+
+ /* mcspi1_cs3.hsusb2_data2 */
+ OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_clk.hsusb2_data7 */
+ OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_simo.hsusb2_data4 */
+ OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_somi.hsusb2_data5 */
+ OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_cs0.hsusb2_data6 */
+ OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* mcspi2_cs1.hsusb2_data3 */
+ OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)
+ >;
+ };
+
wl12xx_gpio: pinmux_wl12xx_gpio {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2180, PIN_OUTPUT | MUX_MODE4) /* uart1_cts.gpio_150 */
@@ -112,6 +151,46 @@
};
};
+&omap3_pmx_core2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_2_pins>;
+
+ ehci_phy_pins: pinmux_ehci_phy_pins {
+ pinctrl-single,pins = <
+
+ /* EHCI PHY reset GPIO etk_d7.gpio_21 */
+ OMAP3630_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4)
+
+ /* EHCI VBUS etk_d8.gpio_22 */
+ OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4)
+ >;
+ };
+
+ /* Used by OHCI and EHCI. OHCI won't work without external phy */
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+
+ /* etk_d10.hsusb2_clk */
+ OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)
+
+ /* etk_d11.hsusb2_stp */
+ OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)
+
+ /* etk_d12.hsusb2_dir */
+ OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* etk_d13.hsusb2_nxt */
+ OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* etk_d14.hsusb2_data0 */
+ OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)
+
+ /* etk_d15.hsusb2_data1 */
+ OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)
+ >;
+ };
+};
+
&omap3_pmx_wkup {
dss_dpi_pins2: pinmux_dss_dpi_pins1 {
pinctrl-single,pins = <
@@ -153,6 +232,29 @@
pinctrl-0 = <&uart3_pins>;
};
+/*
+ * GPIO_61 (nUSB2_EN_1V8) must be low to enable on-board EHCI USB2 interface
+ * for bus switch SN74CB3Q3384A, level-shifter SN74AVC16T245DGGR, and 1.8V.
+ */
+&gpio2 {
+ en_usb2_port {
+ gpio-hog;
+ gpios = <29 GPIO_ACTIVE_HIGH>; /* gpio_61 */
+ output-low;
+ line-name = "enable usb2 port";
+ };
+};
+
+/* T2_GPIO_2 low to route GPIO_61 to on-board devices */
+&twl_gpio {
+ en_on_board_gpio_61 {
+ gpio-hog;
+ gpios = <2 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "en_hsusb2_clk";
+ };
+};
+
&gpmc {
ranges = <0 0 0x30000000 0x1000000>, /* CS0: 16MB for NAND */
<5 0 0x2c000000 0x01000000>;
diff --git a/arch/arm/boot/dts/omap3-evm-common.dtsi b/arch/arm/boot/dts/omap3-evm-common.dtsi
--- a/arch/arm/boot/dts/omap3-evm-common.dtsi
+++ b/arch/arm/boot/dts/omap3-evm-common.dtsi
@@ -12,6 +12,24 @@
};
};
+ /* HS USB Port 2 Power */
+ hsusb2_power: hsusb2_power_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb2_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>; /* gpio_22 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
+ /* HS USB Host PHY on PORT 2 */
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; /* gpio_21 */
+ vcc-supply = <&hsusb2_power>;
+ };
+
leds {
compatible = "gpio-leds";
ledb {
@@ -143,6 +161,14 @@
>;
};
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
+
&usb_otg_hs {
interface-type = <0>;
usb-phy = <&usb2_phy>;
@@ -159,3 +185,10 @@
reg = <5 0 0xff>;
};
};
+
+&vaux2 {
+ regulator-name = "usb_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+};
--
2.13.0
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
