* Jonathan Cameron <jic23@xxxxxxxxxx> [170319 10:08]: > On 17/03/17 01:43, Tony Lindgren wrote: > > On Motorola phones like droid 4 there is a custom CPCAP PMIC. This PMIC > > has ADCs that are used for battery charging and USB PHY VBUS and ID pin > > detection. > > > > Unfortunately the only documentation for this ADC seems to be the > > Motorola mapphone Linux kernel tree. I have tested that reading raw and > > scaled values works, but I have not used the timed sampling that the ADC > > seems to support. > Any link? I'm curious to see just how 'interesting' this was... Well the Motorola kernel has the CPCAP PMIC registers quite nicely documented. I mostly use the "STS-Dev-Team/kernel_mapphone_kexec" git tree as a reference as that has the original Motorola patch imported into a git tree. Below are few links to selected files for fun reading: https://github.com/STS-Dev-Team/kernel_mapphone_kexec https://github.com/STS-Dev-Team/kernel_mapphone_kexec/blob/cm-10.1/drivers/mfd/cpcap-adc.c https://github.com/STS-Dev-Team/kernel_mapphone_kexec/blob/cm-10.1/include/linux/spi/cpcap-regbits.h https://github.com/STS-Dev-Team/kernel_mapphone_kexec/blob/cm-10.1/include/linux/spi/cpcap.h > You are a brave person... Well n950 is too hard to replace.. And n900 is a bit memory limited.. And there are tons of used droid 4 available for about $35 or so :) > > +/* > > + * Temperature lookup table of register values to milliCelcius. > > + * REVISIT: Check the duplicate 0x3ff entry in a freezer > :) Best comment I've seen in a driver for a while! :) > > +static const struct iio_chan_spec cpcap_adc_channels[] = { > > + CPCAP_CHAN(IIO_TEMP, 0, CPCAP_REG_ADCD0, "battdetb"), > > + CPCAP_CHAN(IIO_VOLTAGE, 1, CPCAP_REG_ADCD1, "battp"), > > + CPCAP_CHAN(IIO_VOLTAGE, 2, CPCAP_REG_ADCD2, "vbus"), > > + CPCAP_CHAN(IIO_TEMP, 3, CPCAP_REG_ADCD3, "ad3"), > > + CPCAP_CHAN(IIO_VOLTAGE, 4, CPCAP_REG_ADCD4, "ad4"), > > + CPCAP_CHAN(IIO_CURRENT, 5, CPCAP_REG_ADCD5, "chg_isense"), > > + CPCAP_CHAN(IIO_CURRENT, 6, CPCAP_REG_ADCD6, "batti"), > > + CPCAP_CHAN(IIO_VOLTAGE, 7, CPCAP_REG_ADCD7, "usb_id"), > > + > > + CPCAP_CHAN(IIO_CURRENT, 8, CPCAP_REG_ADCD0, "ad8"), > > + CPCAP_CHAN(IIO_VOLTAGE, 9, CPCAP_REG_ADCD1, "ad9"), > > + CPCAP_CHAN(IIO_VOLTAGE, 10, CPCAP_REG_ADCD2, "licell"), > > + CPCAP_CHAN(IIO_VOLTAGE, 11, CPCAP_REG_ADCD3, "hv_battp"), > > + CPCAP_CHAN(IIO_VOLTAGE, 12, CPCAP_REG_ADCD4, "tsx1_ad12"), > > + CPCAP_CHAN(IIO_VOLTAGE, 13, CPCAP_REG_ADCD5, "tsx2_ad13"), > > + CPCAP_CHAN(IIO_VOLTAGE, 14, CPCAP_REG_ADCD6, "tsy1_ad14"), > > + CPCAP_CHAN(IIO_VOLTAGE, 15, CPCAP_REG_ADCD7, "tsy2_ad15"), > Touch screen kicking around on here as well? Or am I reading too much into > the names? Yeah so it seems. These do not seem to be wired to anything in droid 4, but the Motorola kernel supports a whole family of devices, so it was probably used for touch screen on some at some point. > > + *val = req.result[index]; > > This would come in the seriously unusual category if the scale is integer... > Could be I suppose, but seems unlikely ;) > Note that value in mV should be raw_value * scale. > > I'd guess these are what we term _processed channels, i.e. already in mV? Oh OK, thanks I'll check, yeah it's already in mV. > If all you have is unregister in remove, it's a fairly sure sign > you could have used devm_iio_device_register and dropped the remove > entirely. Sure. Will also look at the other comments and repost, thanks for the review. Regards, Tony -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
