* Rob Herring <robh@xxxxxxxxxx> [170113 08:37]:
> On Tue, Jan 10, 2017 at 07:44:01AM -0800, Tony Lindgren wrote:
> > * Tony Lindgren <tony@xxxxxxxxxxx> [170109 15:43]:
> > > Texas Instruments omap variant SoCs starting with omap4 have a clkctrl
> > > clock controller instance for each interconnect target module. The clkctrl
> > > controls functional and interface clocks for the module.
> > >
> > > The clkctrl clocks are currently handled by arch/arm/mach-omap2 hwmod code.
> > > With this binding and a related clock device driver we can start moving the
> > > clkctrl clock handling to live in drivers/clk/ti.
> > >
> > > For hardware reference, see omap4430 TRM "Table 3-1312. L4PER_CM2 Registers
> > > Mapping Summary" for example. It show one instance of a clkctrl clock
> > > controller with multiple clkctrl registers.
> > >
> > > Note that this binding allows keeping the clockdomain related parts out of
> > > drivers/clock. The CLKCTCTRL and DYNAMICDEP registers can be handled by
> > > using a separate driver in drivers/soc/ti and genpd. If the clockdomain
> > > driver needs to know it's clocks, we can just set the the clkctrl device
> > > instances to be children of the related clockdomain device.
> > >
> > > On omap4 CM_L3INIT_USB_HOST_HS_CLKCTRL on omap5 has eight OPTFCLKEN bits.
> > > So we need to shift the clock index to avoid index conflict for the clock
> > > consumer binding with the next clkctrl offset on omap4.
> > >
> > > Cc: Paul Walmsley <paul@xxxxxxxxx>
> > > Cc: Rob Herring <robh@xxxxxxxxxx>
> > > Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
> > > ---
> > >
> > > So here's what I was able to come up for the clkctr binding based on
> > > all we've discussed so far. Can you guys please take a look and see
> > > if it looks OK to you before we do the device driver?
> > >
> > > Also, does anybody have better suggestions for addressing the optional
> > > clocks in each clkctrl register?
> >
> > The other option that might be worth considering is to make use of the
> > #clock-cells property. Then the index of any optional clock could be passed
> > in the second cell.
> >
> > The third cell could be used to set the modulemode for the clock (software
> > controlled or hardware controlled) instead of using a custom property
> > at the clock controllel level.
>
> I guess I prefer this way. Or you could do a mixture of both proposals
> with 2 cells. The first being the clock id and the 2nd flags.
OK. I don't think we can do it with two cells with using real hardware
offsets for the clocks though. So in that case I'd prefer the three
cell binding as below.
> What's the max optional clocks in theory? B picked from the current
> worst case seems a bit worrying. Why not 16? Upper half is offset, lower
> half is index.
It seems the max is "stuff it into whatever bits are available" in the
register :) And I just noticed omap5 CM_L3INIT_USB_HOST_HS_CLKCTRL has 10
optional clocks, not 8. So yeah let's assume it could be even more.
> > In that case clock consume usage would look like the following using
> > #clock-cells = <3>:
> >
> > #define OMAP4_CLKCTRL_OFFSET 0x20
> > #define MODULEMODE_HWCTRL 1
> > #define MODULEMODE_SWCTRL 2
>
> Can you make one of these 0 instead or is both being set valid?
For MODULEMODE clock 0 means disabed. HWCTRL and SWCTRL are flags for
enabled mode.
So clock index 0 would be the MODULEMODE clock, index 1 first optional clock
and so on. The index could be also be the offset in the actual register
if you prefer that.
> > #define OMAP_CLKCTRL_INDEX(offset) ((offset) - OMAP4_CLKCTRL_OFFSET)
> >
> > #define OMAP4_GPTIMER10_CLKTRL OMAP_CLKCTRL_INDEX(0x28)
> > #define OMAP4_GPTIMER11_CLKTRL OMAP_CLKCTRL_INDEX(0x30)
> > #define OMAP4_GPTIMER2_CLKTRL OMAP_CLKCTRL_INDEX(0x38)
> > ...
> > #define OMAP4_GPIO2_CLKCTRL OMAP_CLKCTRL_INDEX(0x60)
> > ...
> >
> > &gpio2 {
> > clocks = <&cm_l4per_clkctrl OMAP4_GPIO2_CLKCTRL 0 MODULEMODE_HWCTRL
> > &cm_l4per_clkctrl OMAP4_GPIO2_CLKCTRL_DBCLK 1 0>;
>
> Drop the _DBCLK here, right?
Ah sorry yeah this should be:
&gpio2 {
clocks = <&cm_l4per_clkctrl OMAP4_GPIO2_CLKCTRL 0 MODULEMODE_HWCTRL
&cm_l4per_clkctrl OMAP4_GPIO2_CLKCTRL 1 0>;
};
or if using actual bit offsets within the register instead of optional
clock instance count:
&gpio2 {
clocks = <&cm_l4per_clkctrl OMAP4_GPIO2_CLKCTRL 0 MODULEMODE_HWCTRL
&cm_l4per_clkctrl OMAP4_GPIO2_CLKCTRL 8 0>;
};
Regards,
Tony
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
