Add specification for the *pci test* virtual function device. The endpoint function driver and the host pci driver should be created based on this specification. Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx> --- Documentation/PCI/00-INDEX | 2 + Documentation/PCI/endpoint/pci-test-function.txt | 66 ++++++++++++++++++++++ 2 files changed, 68 insertions(+) create mode 100644 Documentation/PCI/endpoint/pci-test-function.txt diff --git a/Documentation/PCI/00-INDEX b/Documentation/PCI/00-INDEX index f84a23c..4e5a283 100644 --- a/Documentation/PCI/00-INDEX +++ b/Documentation/PCI/00-INDEX @@ -16,3 +16,5 @@ endpoint/pci-endpoint.txt - guide to add endpoint controller driver and endpoint function driver. endpoint/pci-endpoint-cfs.txt - guide to use configfs to configure the pci endpoint function. +endpoint/pci-test-function.txt + - specification of *pci test* function device. diff --git a/Documentation/PCI/endpoint/pci-test-function.txt b/Documentation/PCI/endpoint/pci-test-function.txt new file mode 100644 index 0000000..1324376 --- /dev/null +++ b/Documentation/PCI/endpoint/pci-test-function.txt @@ -0,0 +1,66 @@ + PCI TEST + Kishon Vijay Abraham I <kishon@xxxxxx> + +Traditionally PCI RC has always been validated by using standard +PCI cards like ethernet PCI cards or USB PCI cards or SATA PCI cards. +However with the addition of EP-core in linux kernel, it is possible +to configure a PCI controller that can operate in EP mode to work as +a test device. + +The PCI endpoint test device is a virtual device (defined in software) +used to test the endpoint functionality and serve as a sample driver +for other PCI endpoint devices (to use the EP framework). + +The PCI endpoint test device has the following registers: + + 1) PCI_ENDPOINT_TEST_MAGIC + 2) PCI_ENDPOINT_TEST_COMMAND + 3) PCI_ENDPOINT_TEST_STATUS + 4) PCI_ENDPOINT_TEST_SRC_ADDR + 5) PCI_ENDPOINT_TEST_DST_ADDR + 6) PCI_ENDPOINT_TEST_SIZE + 7) PCI_ENDPOINT_TEST_CHECKSUM + +*) PCI_ENDPOINT_TEST_MAGIC + +This register will be used to test BAR0. A known pattern will be written +and read back from MAGIC register to verify BAR0. + +*) PCI_ENDPOINT_TEST_COMMAND: + +This register will be used by the host driver to indicate the function +that the endpoint device must perform. + +Bitfield Description: + Bit 0 : raise legacy irq + Bit 1 : raise MSI irq + Bit 2 - 7 : MSI interrupt number + Bit 8 : read command (read data from RC buffer) + Bit 9 : write command (write data to RC buffer) + Bit 10 : copy command (copy data from one RC buffer to another + RC buffer) + +*) PCI_ENDPOINT_TEST_STATUS + +This register reflects the status of the PCI endpoint device. + +Bitfield Description: + Bit 0 : read success + Bit 1 : read fail + Bit 2 : write success + Bit 3 : write fail + Bit 4 : copy success + Bit 5 : copy fail + Bit 6 : irq raised + Bit 7 : source address is invalid + Bit 8 : destination address is invalid + +*) PCI_ENDPOINT_TEST_SRC_ADDR + +This register contains the source address (RC buffer address) for the +COPY/READ command. + +*) PCI_ENDPOINT_TEST_DST_ADDR + +This register contains the destination address (RC buffer address) for +the COPY/WRITE command. -- 1.7.9.5 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
