From: Kishon Vijay Abraham I <kishon@xxxxxx> Add pinmux configuration for SD card slot and eMMC device found on TI's DRA74x EVM. Only the default modes are supported. For higher speed modes (UHS and HS200) to function, we need full fledged IODelay support in kernel. IODelay support is yet to be added. Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx> [nsekhar@xxxxxx: rebase to mainline/master, use IOPAD() macro, update commit message] Signed-off-by: Sekhar Nori <nsekhar@xxxxxx> --- arch/arm/boot/dts/dra7-evm.dts | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+) diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index 80ebfd6a5c7b..40465d5277e6 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -164,6 +164,33 @@ DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */ >; }; + + mmc1_pins_default: mmc1_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ + DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ + DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ + DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ + DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ + DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ + DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ + >; + }; + + mmc2_pins_default: mmc2_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ + DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ + DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ + DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ + DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ + DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ + DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ + DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ + DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ + DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ + >; + }; }; &i2c1 { @@ -402,6 +429,8 @@ &mmc1 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_default>; vmmc-supply = <&evm_3v3_sd>; vmmc_aux-supply = <&ldo1_reg>; bus-width = <4>; @@ -414,6 +443,8 @@ &mmc2 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_default>; vmmc-supply = <&evm_3v3_sw>; bus-width = <8>; }; -- 2.9.0 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html