On 01/12/16 02:05, Laurent Pinchart wrote:
From: Richard Watts <rrw@xxxxxxxxxxxxx>
The OMAP36xx DPLL5, driving EHCI USB, can be subject to a long-term
frequency drift. The frequency drift magnitude depends on the VCO update
rate, which is inversely proportional to the PLL divider. The kernel
DPLL configuration code results in a high value for the divider, leading
to a long term drift high enough to cause USB transmission errors. In
the worst case the USB PHY's ULPI interface can stop responding,
breaking USB operation completely. This manifests itself on the
Beagleboard xM by the LAN9514 reporting 'Cannot enable port 2. Maybe the
cable is bad?' in the kernel log.
Errata sprz319 advisory 2.1 documents PLL values that minimize the
drift. Use them automatically when DPLL5 is used for USB operation,
which we detect based on the requested clock rate. The clock framework
will still compute the PLL parameters and resulting rate as usual, but
the PLL M and N values will then be overridden. This can result in the
effective clock rate being slightly different than the rate cached by
the clock framework, but won't cause any adverse effect to USB
operation.
Hi Laurent,
Just a minor comment on the documentation; the whole errata document is
identified as sprz319, but for the USB purposes you should only refer to
the advisory 2.1 to avoid confusion.
Some small comments to the code itself below.
Signed-off-by: Richard Watts <rrw@xxxxxxxxxxxxx>
[Upported from v3.2 to v4.9]
Signed-off-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
---
drivers/clk/ti/clk-3xxx.c | 20 +++++++-------
drivers/clk/ti/clock.h | 9 +++++++
drivers/clk/ti/dpll.c | 17 +++++++++++-
drivers/clk/ti/dpll3xxx.c | 69 +++++++++++++++++++++++++++++++++++++++++++++++
4 files changed, 104 insertions(+), 11 deletions(-)
Mike, Stephen, I've kept this as non-intrusive as possible from a CCF point of
view, and decided not to patch the .round_rate() operation to compute the PLL
real output frequency as there is no need to from a USB operation point of
view. Please let me know if you see any issue with that.
Richard, I've pretty much completely rewritten your patch while porting it to
the latest kernel, please let me know if you would like your SoB line and/or
authorship to be removed.
diff --git a/drivers/clk/ti/clk-3xxx.c b/drivers/clk/ti/clk-3xxx.c
index 8831e1a05367..a9d224ecb120 100644
--- a/drivers/clk/ti/clk-3xxx.c
+++ b/drivers/clk/ti/clk-3xxx.c
@@ -22,13 +22,6 @@
#include "clock.h"
-/*
- * DPLL5_FREQ_FOR_USBHOST: USBHOST and USBTLL are the only clocks
- * that are sourced by DPLL5, and both of these require this clock
- * to be at 120 MHz for proper operation.
- */
-#define DPLL5_FREQ_FOR_USBHOST 120000000
-
#define OMAP3430ES2_ST_DSS_IDLE_SHIFT 1
#define OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT 5
#define OMAP3430ES2_ST_SSI_IDLE_SHIFT 8
@@ -546,14 +539,21 @@ void __init omap3_clk_lock_dpll5(void)
struct clk *dpll5_clk;
struct clk *dpll5_m2_clk;
+ /*
+ * Errata spr319f documents a USB host clock drift issue that can be
+ * worked around using specially crafted dpll5 settings with a dpll5_m2
+ * divider set to 8. Set the dpll5 rate to 8x the USB host clock rate,
+ * its .set_rate handler() will detect that frequency and use the errata
+ * settings.
+ */
Refer to advisory 2.1 only here.
dpll5_clk = clk_get(NULL, "dpll5_ck");
- clk_set_rate(dpll5_clk, DPLL5_FREQ_FOR_USBHOST);
+ clk_set_rate(dpll5_clk, OMAP3_DPLL5_FREQ_FOR_USBHOST * 8);
clk_prepare_enable(dpll5_clk);
- /* Program dpll5_m2_clk divider for no division */
+ /* Program dpll5_m2_clk divider */
dpll5_m2_clk = clk_get(NULL, "dpll5_m2_ck");
clk_prepare_enable(dpll5_m2_clk);
- clk_set_rate(dpll5_m2_clk, DPLL5_FREQ_FOR_USBHOST);
+ clk_set_rate(dpll5_m2_clk, OMAP3_DPLL5_FREQ_FOR_USBHOST);
clk_disable_unprepare(dpll5_m2_clk);
clk_disable_unprepare(dpll5_clk);
diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h
index 90f3f472ae1c..13c37f48d9d6 100644
--- a/drivers/clk/ti/clock.h
+++ b/drivers/clk/ti/clock.h
@@ -257,11 +257,20 @@ long omap2_dpll_round_rate(struct clk_hw *hw, unsigned long target_rate,
unsigned long omap3_clkoutx2_recalc(struct clk_hw *hw,
unsigned long parent_rate);
+/*
+ * OMAP3_DPLL5_FREQ_FOR_USBHOST: USBHOST and USBTLL are the only clocks
+ * that are sourced by DPLL5, and both of these require this clock
+ * to be at 120 MHz for proper operation.
+ */
+#define OMAP3_DPLL5_FREQ_FOR_USBHOST 120000000
+
unsigned long omap3_dpll_recalc(struct clk_hw *hw, unsigned long parent_rate);
int omap3_dpll4_set_rate(struct clk_hw *clk, unsigned long rate,
unsigned long parent_rate);
int omap3_dpll4_set_rate_and_parent(struct clk_hw *hw, unsigned long rate,
unsigned long parent_rate, u8 index);
+int omap3_dpll5_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate);
void omap3_clk_lock_dpll5(void);
unsigned long omap4_dpll_regm4xen_recalc(struct clk_hw *hw,
diff --git a/drivers/clk/ti/dpll.c b/drivers/clk/ti/dpll.c
index 9fc8754a6e61..ac8645be9249 100644
--- a/drivers/clk/ti/dpll.c
+++ b/drivers/clk/ti/dpll.c
@@ -114,6 +114,18 @@ static const struct clk_ops omap3_dpll_ck_ops = {
.round_rate = &omap2_dpll_round_rate,
};
+static const struct clk_ops omap3_dpll5_ck_ops = {
+ .enable = &omap3_noncore_dpll_enable,
+ .disable = &omap3_noncore_dpll_disable,
+ .get_parent = &omap2_init_dpll_parent,
+ .recalc_rate = &omap3_dpll_recalc,
+ .set_rate = &omap3_dpll5_set_rate,
+ .set_parent = &omap3_noncore_dpll_set_parent,
+ .set_rate_and_parent = &omap3_noncore_dpll_set_rate_and_parent,
+ .determine_rate = &omap3_noncore_dpll_determine_rate,
+ .round_rate = &omap2_dpll_round_rate,
+};
+
static const struct clk_ops omap3_dpll_per_ck_ops = {
.enable = &omap3_noncore_dpll_enable,
.disable = &omap3_noncore_dpll_disable,
@@ -474,7 +486,10 @@ static void __init of_ti_omap3_dpll_setup(struct device_node *node)
.modes = (1 << DPLL_LOW_POWER_BYPASS) | (1 << DPLL_LOCKED),
};
- of_ti_dpll_setup(node, &omap3_dpll_ck_ops, &dd);
+ if (!strcmp(node->name, "dpll5_ck"))
Move the of_machine_is_compatible() checks here also, so you will avoid
executing those runtime, and don't need any checks in the
omap3_dpll5_set_rate func.
+ of_ti_dpll_setup(node, &omap3_dpll5_ck_ops, &dd);
+ else
+ of_ti_dpll_setup(node, &omap3_dpll_ck_ops, &dd);
}
CLK_OF_DECLARE(ti_omap3_dpll_clock, "ti,omap3-dpll-clock",
of_ti_omap3_dpll_setup);
diff --git a/drivers/clk/ti/dpll3xxx.c b/drivers/clk/ti/dpll3xxx.c
index 88f2ce81ba55..c8395f7c2ff9 100644
--- a/drivers/clk/ti/dpll3xxx.c
+++ b/drivers/clk/ti/dpll3xxx.c
@@ -838,3 +838,72 @@ int omap3_dpll4_set_rate_and_parent(struct clk_hw *hw, unsigned long rate,
return omap3_noncore_dpll_set_rate_and_parent(hw, rate, parent_rate,
index);
}
+
+static bool omap3_dpll5_apply_sprz319(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
Please rename this to something else, sprz319 can refer to _any_ errata
under the document, which is confusing. Maybe just
omap3_dpll5_apply_errata(), and add a kerneldoc comment for the function
that it applies the advisory 2.1.
+ struct omap3_dpll5_settings {
+ unsigned int rate, m, n;
+ };
+
+ static const struct omap3_dpll5_settings precomputed[] = {
+ /*
+ * From DM3730 errata (sprz319f), table 35 and 36.
Drop sprz319f and replace with advisory 2.1.
+ * The N value is increased by 1 compared to the tables as the
+ * errata lists register values while last_rounded_field is the
+ * real divider value.
+ */
+ { 12000000, 80, 0+1 },
+ { 13000000, 443, 5+1 },
+ { 19200000, 50, 0+1 },
+ { 26000000, 443, 11+1 },
+ { 38400000, 25, 0+1 }
+ };
+
+ const struct omap3_dpll5_settings *d;
+ struct clk_hw_omap *clk = to_clk_hw_omap(hw);
+ struct dpll_data *dd;
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(precomputed); ++i) {
+ if (parent_rate == precomputed[i].rate)
+ break;
+ }
+
+ if (i == ARRAY_SIZE(precomputed))
+ return false;
+
+ d = &precomputed[i];
+
+ /* Update the M, N and rounded rate values and program the DPLL. */
+ dd = clk->dpll_data;
+ dd->last_rounded_m = d->m;
+ dd->last_rounded_n = d->n;
+ dd->last_rounded_rate = div_u64((u64)parent_rate * d->m, d->n);
+ omap3_noncore_dpll_program(clk, 0);
+
+ return true;
+}
+
+/**
+ * omap3_dpll5_set_rate - set rate for omap3 dpll5
+ * @hw: clock to change
+ * @rate: target rate for clock
+ * @parent_rate: rate of the parent clock
+ *
+ * Set rate for the DPLL5 clock. Apply the sprz319 advisory 2.1 on OMAP36xx if
+ * the DPLL is used for USB host (detected through the requested rate).
+ */
+int omap3_dpll5_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ if (of_machine_is_compatible("ti,omap3630") ||
+ of_machine_is_compatible("ti,omap36xx")) {
Drop the of_machine_is_compatible checks from here once you do the
change proposed during init.
-Tero
+ if (rate == OMAP3_DPLL5_FREQ_FOR_USBHOST * 8) {
+ if (omap3_dpll5_apply_sprz319(hw, parent_rate))
+ return 0;
+ }
+ }
+
+ return omap3_noncore_dpll_set_rate(hw, rate, parent_rate);
+}
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
