Re: [PATCH v4] rtc: omap: Support ext_wakeup configuration

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Aug 25, 2016 at 01:19:12PM +0200, Marcin Niestroj wrote:
> Support configuration of ext_wakeup sources. This patch makes it
> possible to enable ext_wakeup and set it's polarity, depending on board
> configuration. AM335x's dedicated PMIC (tps65217) uses ext_wakeup to
> notify about power-button presses. Handling power-button presses enables
> to recover from RTC-only power states correctly.
> 
> Signed-off-by: Marcin Niestroj <m.niestroj@xxxxxxxxxxxxxxxx>
> ---
> Hi,
> 
> This is a total reimplementation, so it is not based on any of the previos
> patch versions. This patch adds support for ext_wakeup using generic pinconf
> device-tree bindings, with one added "ti,input-polarity" custom property.
> This approach has been suggested by Tony and Grygorii in [1].
> 
> Patch was developed on 4.6, rebased on 4.8-rc3, tested using chiliBoard.
> 
> [1] http://www.spinics.net/lists/devicetree/msg131516.html
> 
>  Documentation/devicetree/bindings/rtc/rtc-omap.txt |  21 +++
>  drivers/rtc/Kconfig                                |   1 +
>  drivers/rtc/rtc-omap.c                             | 167 ++++++++++++++++++++-
>  3 files changed, 181 insertions(+), 8 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/rtc/rtc-omap.txt b/Documentation/devicetree/bindings/rtc/rtc-omap.txt
> index bf7d11a..5d18373 100644
> --- a/Documentation/devicetree/bindings/rtc/rtc-omap.txt
> +++ b/Documentation/devicetree/bindings/rtc/rtc-omap.txt
> @@ -18,6 +18,18 @@ Optional properties:
>    through pmic_power_en
>  - clocks: Any internal or external clocks feeding in to rtc
>  - clock-names: Corresponding names of the clocks
> +- pinctrl-0: a phandle pointing to the pin settings for the device
> +- pinctrl-names: should be "default"
> +
> +Optional subnodes:
> +- generic pinctrl node
> +
> +Required pinctrl subnodes properties:
> +- pins - Names of ext_wakeup pins to configure
> +
> +Optional pinctrl subnodes properties:
> +- input-enable - Enables ext_wakeup
> +- ti,input-polarity - GPIO_ACTIVE_LOW or GPIO_ACTIVE_HIGH depending board

This is not a GPIO, so don't use GPIO defines. Just make this boolean 
with not present ideally being the more common case.

>  Example:
>  
> @@ -30,4 +42,13 @@ rtc@1c23000 {
>  	system-power-controller;
>  	clocks = <&clk_32k_rtc>, <&clk_32768_ck>;
>  	clock-names = "ext-clk", "int-clk";
> +
> +	pinctrl-0 = <&ext_wakeup>;
> +	pinctrl-names = "default";
> +
> +	ext_wakeup: ext_wakeup {

Use '-', not '_' in node names.

> +		pins = "ext_wakeup0";
> +		input-enable;
> +		ti,input-polarity = <GPIO_ACTIVE_LOW>;
> +	};
>  };
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux