On Saturday 11 June 2016 04:34 AM, Schuyler Patton wrote: > > > On 06/08/2016 07:03 PM, Ivan Khoronzhuk wrote: >> >> >> On 09.06.16 02:11, Schuyler Patton wrote: >>> >>> >>> On 06/08/2016 09:06 AM, Ivan Khoronzhuk wrote: >>>> >>>> >>>> On 08.06.16 17:01, Ivan Khoronzhuk wrote: >>>>> Hi Schuyer, >>>>> >>>>> On 07.06.16 18:26, Schuyler Patton wrote: >>>>>> Hi, >>>>>> >>>>>> On 06/07/2016 08:59 AM, Ivan Khoronzhuk wrote: >>>>>>> There is no reason in rx_descs property because davinici_cpdma >>>>>>> driver splits pool of descriptors equally between tx and rx >>>>>>> channels. >>>>>>> So, this patch series makes driver to use available number of >>>>>>> descriptors for rx channels. >>>>>> >>>>>> I agree with the idea of consolidating how the descriptors are >>>>>> defined because of >>>>>> the two variable components, number and size of the pool can be >>>>>> confusing to >>>>>> end users. I would like to request to change how it is being >>>>>> proposed here. >>>>>> >>>>>> I think the number of descriptors should be left in the device >>>>>> tree source file as >>>>>> is and remove the BD size variable and have the driver calculate >>>>>> the size of the >>>>>> pool necessary to support the descriptor request. From an user >>>>>> perspective it is >>>>>> easier I think to be able to list the number of descriptors >>>>>> necessary vs. the size >>>>>> of the pool. >>>>>> >>>>>> Since the patch series points out how it is used so in the driver >>>>>> so to make that >>>>>> consistent is perhaps change rx_descs to total_descs. >>>>>> >>>>>> Regards, >>>>>> Schuyler >>>>> >>>>> The DT entry for cpsw doesn't have property for size of the pool. >>>>> It contains only BD ram size, if you mean this. The size of the >>>>> pool is >>>>> software decision. Current version of DT entry contain only rx desc >>>>> number. >>>>> That is not correct, as it depends on the size of the descriptor, >>>>> which is also >>>>> h/w parameter. The DT entry has to describe only h/w part and >>>>> shouldn't contain >>>>> driver implementation details, and I'm looking on it from this >>>>> perspective. >>>>> >>>>> Besides, rx_descs describes only rx number of descriptors, that are >>>>> taken from >>>>> the same pool as tx descriptors, and setting rx desc to some new >>>>> value doesn't >>>>> mean that rest of them are freed for tx. Also, I'm going to send >>>>> series that >>>>> adds multi channel support to the driver, and in this case, >>>>> splitting of the >>>>> pool will be more sophisticated than now, after what setting those >>>>> parameters >>>>> for user (he should do this via device tree) can be even more >>>>> confusing. But, >>>> should -> shouldn't >>>> >>>>> as it's supposed, it's software decision that shouldn't leak to the >>>>> DT. >>> >>> If this rx-desc field is removed how will the number of descriptors >>> be set? >>> >>> This field has been used to increase the number of descriptors so high >>> volume short packets are not dropped due to descriptor exhaustion. >>> The current >>> default number of 64 rx descriptors is too low for gigabit networks. >>> Some users >>> have a strong requirement for zero loss of UDP packets setting this >>> field to a >>> larger number and setting the descriptors off-chip was a means to solve >>> the problem. >> The current implementation of cpdma driver splits descs num on 2 parts >> equally. >> Total number = 256, then 128 reserved for rx and 128 for tx, but >> setting this to >> 64, simply limits usage of reserved rx descriptors to 64, so that: >> 64 rx descs, 128 tx descs and 64 are always present in the pool but >> cannot be used, >> (as new rx descriptor is allocated only after previous was freed). >> That means, 64 rx descs are unused. In case of rx descriptor >> exhaustion, an user can >> set rx_descs to 128, for instance, in this case all descriptors will >> be in use, but then question, >> why intentionally limit number of rx descs, anyway rest 64 descs >> cannot be used for other >> purposes. In case of this patch, all rx descs are in use, and no need >> to correct number >> of rx descs anymore, use all of them....and it doesn't have impact on >> performance, as >> anyway, bunch of rx descs were simply limited by DT and unused. So, >> probably, there is no >> reason to worry about that. > > When we see this issue we set the descriptors to DDR and put a large number > in the desc count. unfortunately I wish I could provide a number, > usually the issue > is a volume burst of short UDP packets. > >> >> PS: >> It doesn't concern this patch, but, which PPS makes rx descs to be >> exhausted?... >> (In this case "desc_alloc_fail" counter contains some value for rx >> channel, >> and can be read with "ethtool -S eth0". Also, the user will be WARNed >> ON by the driver) >> >> it's interesting to test it, I'm worrying about, because in case of >> multichannel, >> the pool is split between all channels... they are throughput limited, >> but >> anyway, it's good to correlate the number of descs with throughput >> assigned to >> a channel, if possible. That has to be possible, if setting to 128 >> helps, then >> has to be value between 64 and 128 to make handling of rx packets fast >> enough. >> After what, can be calculated correlation between number of rx descs >> and throughput >> split between channels.... > > With gigabit networks 64 or 128 rx descriptors is not going to enough to > fix the > DMA overrun problem. Usually we set this number to an arbitrarily large > 2000 > descriptors in external DDR to demonstrate it is possible to not drop > packets. All > this does is move the problem higher up so that the drops occur in network > stack if the ARM is overloaded. With the high speed networks I would like > to propose that the descriptor pool or pools are moved to DDR by > default. It would > be nice to have some reconfigurability or set a pool size that reduces > or eliminates > the DMA issue that is seen in these types of applications. > > This test gets used a lot, which is to send very short UDP packets. If I > have the math > right, a 52 byte (64 byte with the inter-frame gap) UDP packet the > default 64 > descriptors gets consumed in roughly 33uS. There are the switch fifos > which will also > allow some headroom, but a user was dropping packets at the switch when > they > were bursting 360 packets at the processor on a gigabit link > I too agree that rx-descs can be derived from the pool size and descriptor size in driver itself. The current driver uses bd_ram_size to set the pool size when the descriptors are placed in DDR which is wrong. Here I propose an idea to solve Schuyler's concern to keep the descriptors in DDR when a system need more rx descriptors for lossless UDB performance. The DT property rx-descs can be removed and add a new DT property *pool_size* to add support for descriptors memory size in DDR and define a pool size which the system needs for a network to have lossless UDP transfers. So based on no_bd_ram DT entry, the driver can decide whether it can use internal BD-ram or DDR to initialize the cpdma driver. Regards Mugunthan V N -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
