From: Yegor Yefremov <yegorslists@xxxxxxxxxxxxxx>
Introduce serial8250_out_MCR() and serial8250_in_MCR() routines, that
replace following calls:
serial_out(port, UART_MCR, val)
serial_port_out(up, UART_MCR, val)
serial_in(port, UART_MCR)
This patch is needed in order to integrate reading/writing of MCR
signals via SERIAL_MCTRL_GPIO infrastructure later.
Reviewed-by: Peter Hurley <peter@xxxxxxxxxxxxxxxxxx>
Signed-off-by: Yegor Yefremov <yegorslists@xxxxxxxxxxxxxx>
---
Changes:
v2: rebase against tty-next (4.5-rc6)
drivers/tty/serial/8250/8250.h | 10 ++++++++
drivers/tty/serial/8250/8250_omap.c | 4 ++--
drivers/tty/serial/8250/8250_port.c | 47 ++++++++++++++++++-------------------
3 files changed, 35 insertions(+), 26 deletions(-)
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index 215a992..533661c 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -131,6 +131,16 @@ void serial8250_rpm_put(struct uart_8250_port *p);
int serial8250_em485_init(struct uart_8250_port *p);
void serial8250_em485_destroy(struct uart_8250_port *p);
+static inline void serial8250_out_MCR(struct uart_8250_port *up, int value)
+{
+ serial_out(up, UART_MCR, value);
+}
+
+static inline int serial8250_in_MCR(struct uart_8250_port *up)
+{
+ return serial_in(up, UART_MCR);
+}
+
#if defined(__alpha__) && !defined(CONFIG_PCI)
/*
* Digital did something really horribly wrong with the OUT1 and OUT2
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index 2c44c79..61ad6c3 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -280,7 +280,7 @@ static void omap8250_restore_regs(struct uart_8250_port *up)
serial_out(up, UART_EFR, UART_EFR_ECB);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
- serial_out(up, UART_MCR, UART_MCR_TCRTLR);
+ serial8250_out_MCR(up, UART_MCR_TCRTLR);
serial_out(up, UART_FCR, up->fcr);
omap8250_update_scr(up, priv);
@@ -296,7 +296,7 @@ static void omap8250_restore_regs(struct uart_8250_port *up)
serial_out(up, UART_LCR, 0);
/* drop TCR + TLR access, we setup XON/XOFF later */
- serial_out(up, UART_MCR, up->mcr);
+ serial8250_out_MCR(up, up->mcr);
serial_out(up, UART_IER, up->ier);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index d403603..d2b1825 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -527,13 +527,13 @@ static void serial8250_clear_fifos(struct uart_8250_port *p)
static inline void serial8250_em485_rts_after_send(struct uart_8250_port *p)
{
- unsigned char mcr = serial_in(p, UART_MCR);
+ unsigned char mcr = serial8250_in_MCR(p);
if (p->port.rs485.flags & SER_RS485_RTS_AFTER_SEND)
mcr |= UART_MCR_RTS;
else
mcr &= ~UART_MCR_RTS;
- serial_out(p, UART_MCR, mcr);
+ serial8250_out_MCR(p, mcr);
}
static void serial8250_em485_handle_start_tx(unsigned long arg);
@@ -785,10 +785,10 @@ static int size_fifo(struct uart_8250_port *up)
old_lcr = serial_in(up, UART_LCR);
serial_out(up, UART_LCR, 0);
old_fcr = serial_in(up, UART_FCR);
- old_mcr = serial_in(up, UART_MCR);
+ old_mcr = serial8250_in_MCR(up);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
- serial_out(up, UART_MCR, UART_MCR_LOOP);
+ serial8250_out_MCR(up, UART_MCR_LOOP);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
old_dl = serial_dl_read(up);
serial_dl_write(up, 0x0001);
@@ -800,7 +800,7 @@ static int size_fifo(struct uart_8250_port *up)
(count < 256); count++)
serial_in(up, UART_RX);
serial_out(up, UART_FCR, old_fcr);
- serial_out(up, UART_MCR, old_mcr);
+ serial8250_out_MCR(up, old_mcr);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
serial_dl_write(up, old_dl);
serial_out(up, UART_LCR, old_lcr);
@@ -1040,17 +1040,17 @@ static void autoconfig_16550a(struct uart_8250_port *up)
* it's changed. If so, set baud_base in EXCR2 to 921600. -- dwmw2
*/
serial_out(up, UART_LCR, 0);
- status1 = serial_in(up, UART_MCR);
+ status1 = serial8250_in_MCR(up);
serial_out(up, UART_LCR, 0xE0);
status2 = serial_in(up, 0x02); /* EXCR1 */
if (!((status2 ^ status1) & UART_MCR_LOOP)) {
serial_out(up, UART_LCR, 0);
- serial_out(up, UART_MCR, status1 ^ UART_MCR_LOOP);
+ serial8250_out_MCR(up, status1 ^ UART_MCR_LOOP);
serial_out(up, UART_LCR, 0xE0);
status2 = serial_in(up, 0x02); /* EXCR1 */
serial_out(up, UART_LCR, 0);
- serial_out(up, UART_MCR, status1);
+ serial8250_out_MCR(up, status1);
if ((status2 ^ status1) & UART_MCR_LOOP) {
unsigned short quot;
@@ -1224,7 +1224,7 @@ static void autoconfig(struct uart_8250_port *up)
}
}
- save_mcr = serial_in(up, UART_MCR);
+ save_mcr = serial8250_in_MCR(up);
save_lcr = serial_in(up, UART_LCR);
/*
@@ -1237,9 +1237,9 @@ static void autoconfig(struct uart_8250_port *up)
* that conflicts with COM 1-4 --- we hope!
*/
if (!(port->flags & UPF_SKIP_TEST)) {
- serial_out(up, UART_MCR, UART_MCR_LOOP | 0x0A);
+ serial8250_out_MCR(up, UART_MCR_LOOP | 0x0A);
status1 = serial_in(up, UART_MSR) & 0xF0;
- serial_out(up, UART_MCR, save_mcr);
+ serial8250_out_MCR(up, save_mcr);
if (status1 != 0x90) {
spin_unlock_irqrestore(&port->lock, flags);
DEBUG_AUTOCONF("LOOP test failed (%02x) ",
@@ -1305,7 +1305,7 @@ static void autoconfig(struct uart_8250_port *up)
if (port->type == PORT_RSA)
serial_out(up, UART_RSA_FRR, 0);
#endif
- serial_out(up, UART_MCR, save_mcr);
+ serial8250_out_MCR(up, save_mcr);
serial8250_clear_fifos(up);
serial_in(up, UART_RX);
if (up->capabilities & UART_CAP_UUE)
@@ -1353,19 +1353,18 @@ static void autoconfig_irq(struct uart_8250_port *up)
/* forget possible initially masked and pending IRQ */
probe_irq_off(probe_irq_on());
- save_mcr = serial_in(up, UART_MCR);
+ save_mcr = serial8250_in_MCR(up);
save_ier = serial_in(up, UART_IER);
- serial_out(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2);
+ serial8250_out_MCR(up, UART_MCR_OUT1 | UART_MCR_OUT2);
irqs = probe_irq_on();
- serial_out(up, UART_MCR, 0);
+ serial8250_out_MCR(up, 0);
udelay(10);
if (port->flags & UPF_FOURPORT) {
- serial_out(up, UART_MCR,
- UART_MCR_DTR | UART_MCR_RTS);
+ serial8250_out_MCR(up, UART_MCR_DTR | UART_MCR_RTS);
} else {
- serial_out(up, UART_MCR,
- UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2);
+ serial8250_out_MCR(up,
+ UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2);
}
serial_out(up, UART_IER, 0x0f); /* enable all intrs */
serial_in(up, UART_LSR);
@@ -1376,7 +1375,7 @@ static void autoconfig_irq(struct uart_8250_port *up)
udelay(20);
irq = probe_irq_off(irqs);
- serial_out(up, UART_MCR, save_mcr);
+ serial8250_out_MCR(up, save_mcr);
serial_out(up, UART_IER, save_ier);
if (port->flags & UPF_FOURPORT)
@@ -1549,14 +1548,14 @@ static inline void start_tx_rs485(struct uart_port *port)
del_timer(&em485->stop_tx_timer);
em485->active_timer = NULL;
- mcr = serial_in(up, UART_MCR);
+ mcr = serial8250_in_MCR(up);
if (!!(up->port.rs485.flags & SER_RS485_RTS_ON_SEND) !=
!!(mcr & UART_MCR_RTS)) {
if (up->port.rs485.flags & SER_RS485_RTS_ON_SEND)
mcr |= UART_MCR_RTS;
else
mcr &= ~UART_MCR_RTS;
- serial_out(up, UART_MCR, mcr);
+ serial8250_out_MCR(up, mcr);
if (up->port.rs485.delay_rts_before_send > 0) {
em485->active_timer = &em485->start_tx_timer;
@@ -1944,7 +1943,7 @@ void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl)
mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr;
- serial_port_out(port, UART_MCR, mcr);
+ serial8250_out_MCR(up, mcr);
}
EXPORT_SYMBOL_GPL(serial8250_do_set_mctrl);
@@ -3093,7 +3092,7 @@ static void serial8250_console_restore(struct uart_8250_port *up)
serial8250_set_divisor(port, baud, quot, frac);
serial_port_out(port, UART_LCR, up->lcr);
- serial_port_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS);
+ serial8250_out_MCR(up, UART_MCR_DTR | UART_MCR_RTS);
}
/*
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
