On 4/12/2016 3:52 AM, Grygorii Strashko wrote:
Now GPIO IRQ loss is observed on dra7-evm after suspend/resume cycle
in the following case:
extcon_usb1(id_irq) -> pcf8575.gpio1 -> omapgpio6.gpio11 -> gic
the extcon_usb1 is wake up source and it enables IRQ wake up for
id_irq by calling enable/disable_irq_wake() during suspend/resume
which, in turn, causes execution of omap_gpio_wake_enable(). And
omap_gpio_wake_enable() will set/clear corresponding bit in
GPIO_IRQWAKEN_x register.
omapgpio6 configuration after boot - wakeup is enabled for GPIO IRQs
by default from omap_gpio_irq_type:
GPIO_IRQSTATUS_SET_0 | 0x00000400
GPIO_IRQSTATUS_CLR_0 | 0x00000400
GPIO_IRQWAKEN_0 | 0x00000400
GPIO_RISINGDETECT | 0x00000000
GPIO_FALLINGDETECT | 0x00000400
omapgpio6 configuration after after suspend/resume cycle:
GPIO_IRQSTATUS_SET_0 | 0x00000400
GPIO_IRQSTATUS_CLR_0 | 0x00000400
GPIO_IRQWAKEN_0 | 0x00000000 <---
GPIO_RISINGDETECT | 0x00000000
GPIO_FALLINGDETECT | 0x00000400
As result, system will start to lose interrupts from pcf8575 GPIO
expander, because when OMAP GPIO IP is in smart-idle wakeup mode, there
is no guarantee that transition(s) on input non wake up GPIO pin will
trigger asynchronous wake-up request to PRCM and then IRQ generation.
IRQ will be generated when GPIO is in active mode - for example, some
time after accessing GPIO bank registers IRQs will be generated
normally, but issue will happen again once PRCM will put GPIO in low
power smart-idle wakeup mode.
Note 1. Issue is not reproduced if debounce clk is enabled for GPIO
bank.
Note 2. Issue hardly reproducible if GPIO pins group contains both
wakeup/non-wakeup gpios - for example, it will be hard to reproduce
issue with pin2 if GPIO_IRQWAKEN_0=0x1 GPIO_IRQSTATUS_SET_0=0x3
GPIO_FALLINGDETECT = 0x3 (TRM "Power Saving by Grouping the Edge/Level
Detection").
Note 3. There nothing common bitween System wake up and OMAP GPIO bank
IP wake up logic - the last one defines how the GPIO bank ON-IDLE-ON
transition will happen inside SoC under control of PRCM.
Hence, fix the problem by removing omap_set_gpio_wakeup() function
completely and so keeping always in sync GPIO IRQ mask/unmask
(IRQSTATUS_SET) and wake up enable (GPIO_IRQWAKEN) bits; and adding
IRQCHIP_MASK_ON_SUSPEND flag in OMAP GPIO irqchip. That way non wakeup
GPIO IRQs will be properly masked/unmask by IRQ PM core during
suspend/resume cycle.
Cc: Roger Quadros <rogerq@xxxxxx>
Signed-off-by: Grygorii Strashko <grygorii.strashko@xxxxxx>
---
GPIO IP has two levels of controls for wakeups and you are
just removing the SYSCFG wakeup and relying on the IRQ
line wakeup. I like usage of "IRQCHIP_MASK_ON_SUSPEND" but
please be acreful this change which might break older OMAPs.
drivers/gpio/gpio-omap.c | 42 ++----------------------------------------
1 file changed, 2 insertions(+), 40 deletions(-)
diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index 551dfa9..b98ede7 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -611,51 +611,12 @@ static inline void omap_set_gpio_irqenable(struct gpio_bank *bank,
omap_disable_gpio_irqbank(bank, BIT(offset));
}
-/*
- * Note that ENAWAKEUP needs to be enabled in GPIO_SYSCONFIG register.
- * 1510 does not seem to have a wake-up register. If JTAG is connected
- * to the target, system will wake up always on GPIO events. While
- * system is running all registered GPIO interrupts need to have wake-up
- * enabled. When system is suspended, only selected GPIO interrupts need
- * to have wake-up enabled.
- */
-static int omap_set_gpio_wakeup(struct gpio_bank *bank, unsigned offset,
- int enable)
-{
- u32 gpio_bit = BIT(offset);
- unsigned long flags;
-
- if (bank->non_wakeup_gpios & gpio_bit) {
- dev_err(bank->chip.parent,
- "Unable to modify wakeup on non-wakeup GPIO%d\n",
- offset);
- return -EINVAL;
- }
-
- raw_spin_lock_irqsave(&bank->lock, flags);
- if (enable)
- bank->context.wake_en |= gpio_bit;
- else
- bank->context.wake_en &= ~gpio_bit;
-
- writel_relaxed(bank->context.wake_en, bank->base + bank->regs->wkup_en);
- raw_spin_unlock_irqrestore(&bank->lock, flags);
-
- return 0;
-}
-
/* Use disable_irq_wake() and enable_irq_wake() functions from drivers */
static int omap_gpio_wake_enable(struct irq_data *d, unsigned int enable)
{
struct gpio_bank *bank = omap_irq_data_get_bank(d);
- unsigned offset = d->hwirq;
- int ret;
- ret = omap_set_gpio_wakeup(bank, offset, enable);
- if (!ret)
- ret = irq_set_irq_wake(bank->irq, enable);
-
- return ret;
+ return irq_set_irq_wake(bank->irq, enable);
}
static int omap_gpio_request(struct gpio_chip *chip, unsigned offset)
@@ -1187,6 +1148,7 @@ static int omap_gpio_probe(struct platform_device *pdev)
irqc->irq_bus_lock = omap_gpio_irq_bus_lock,
irqc->irq_bus_sync_unlock = gpio_irq_bus_sync_unlock,
irqc->name = dev_name(&pdev->dev);
+ irqc->flags = IRQCHIP_MASK_ON_SUSPEND;
bank->irq = platform_get_irq(pdev, 0);
if (bank->irq <= 0) {
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
