Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@xxxxxxxxxxxxxxx>
---
arch/arm/boot/dts/omap3-n900.dts | 106 +++++++++++++++++++--------------------
1 file changed, 53 insertions(+), 53 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 5f5e0f3d5b64..f8a20f32e26c 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -149,15 +149,15 @@
uart2_pins: pinmux_uart2_pins {
pinctrl-single,pins = <
- 0x14a (PIN_INPUT | MUX_MODE0) /* uart2_rx */
- 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
+ OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx */
+ OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
>;
};
uart3_pins: pinmux_uart3_pins {
pinctrl-single,pins = <
- 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx */
- 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx */
+ OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx */
+ OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx */
>;
};
@@ -198,22 +198,22 @@
i2c1_pins: pinmux_i2c1_pins {
pinctrl-single,pins = <
- 0x18a (PIN_INPUT | MUX_MODE0) /* i2c1_scl */
- 0x18c (PIN_INPUT | MUX_MODE0) /* i2c1_sda */
+ OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl */
+ OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda */
>;
};
i2c2_pins: pinmux_i2c2_pins {
pinctrl-single,pins = <
- 0x18e (PIN_INPUT | MUX_MODE0) /* i2c2_scl */
- 0x190 (PIN_INPUT | MUX_MODE0) /* i2c2_sda */
+ OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
+ OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
>;
};
i2c3_pins: pinmux_i2c3_pins {
pinctrl-single,pins = <
- 0x192 (PIN_INPUT | MUX_MODE0) /* i2c3_scl */
- 0x194 (PIN_INPUT | MUX_MODE0) /* i2c3_sda */
+ OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */
+ OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */
>;
};
@@ -225,85 +225,85 @@
mcspi4_pins: pinmux_mcspi4_pins {
pinctrl-single,pins = <
- 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */
- 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_somi */
- 0x160 (PIN_OUTPUT | MUX_MODE1) /* mcspi4_simo */
- 0x166 (PIN_OUTPUT | MUX_MODE1) /* mcspi4_cs0 */
+ OMAP3_CORE1_IOPAD(0x218c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */
+ OMAP3_CORE1_IOPAD(0x2192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_somi */
+ OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE1) /* mcspi4_simo */
+ OMAP3_CORE1_IOPAD(0x2196, PIN_OUTPUT | MUX_MODE1) /* mcspi4_cs0 */
>;
};
mmc1_pins: pinmux_mmc1_pins {
pinctrl-single,pins = <
- 0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
- 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
- 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */
- 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
- 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
- 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
+ OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
+ OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
+ OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */
+ OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
+ OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
+ OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
>;
};
mmc2_pins: pinmux_mmc2_pins {
pinctrl-single,pins = <
- 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */
- 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */
- 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */
- 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */
- 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */
- 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */
- 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat4 */
- 0x136 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat5 */
- 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat6 */
- 0x13a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7 */
+ OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */
+ OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */
+ OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */
+ OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */
+ OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */
+ OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */
+ OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat4 */
+ OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat5 */
+ OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat6 */
+ OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7 */
>;
};
acx565akm_pins: pinmux_acx565akm_pins {
pinctrl-single,pins = <
- 0x0d4 (PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */
+ OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */
>;
};
dss_sdi_pins: pinmux_dss_sdi_pins {
pinctrl-single,pins = <
- 0x0c0 (PIN_OUTPUT | MUX_MODE1) /* dss_data10.sdi_dat1n */
- 0x0c2 (PIN_OUTPUT | MUX_MODE1) /* dss_data11.sdi_dat1p */
- 0x0c4 (PIN_OUTPUT | MUX_MODE1) /* dss_data12.sdi_dat2n */
- 0x0c6 (PIN_OUTPUT | MUX_MODE1) /* dss_data13.sdi_dat2p */
+ OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE1) /* dss_data10.sdi_dat1n */
+ OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE1) /* dss_data11.sdi_dat1p */
+ OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE1) /* dss_data12.sdi_dat2n */
+ OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE1) /* dss_data13.sdi_dat2p */
- 0x0d8 (PIN_OUTPUT | MUX_MODE1) /* dss_data22.sdi_clkp */
- 0x0da (PIN_OUTPUT | MUX_MODE1) /* dss_data23.sdi_clkn */
+ OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE1) /* dss_data22.sdi_clkp */
+ OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE1) /* dss_data23.sdi_clkn */
>;
};
wl1251_pins: pinmux_wl1251 {
pinctrl-single,pins = <
- 0x0ce (PIN_OUTPUT | MUX_MODE4) /* gpio 87 => wl1251 enable */
- 0x05a (PIN_INPUT | MUX_MODE4) /* gpio 42 => wl1251 irq */
+ OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE4) /* gpio 87 => wl1251 enable */
+ OMAP3_CORE1_IOPAD(0x208a, PIN_INPUT | MUX_MODE4) /* gpio 42 => wl1251 irq */
>;
};
ssi_pins: pinmux_ssi {
pinctrl-single,pins = <
- 0x150 (PIN_INPUT_PULLUP | MUX_MODE1) /* ssi1_rdy_tx */
- 0x14e (PIN_OUTPUT | MUX_MODE1) /* ssi1_flag_tx */
- 0x152 (PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */
- 0x14c (PIN_OUTPUT | MUX_MODE1) /* ssi1_dat_tx */
- 0x154 (PIN_INPUT | MUX_MODE1) /* ssi1_dat_rx */
- 0x156 (PIN_INPUT | MUX_MODE1) /* ssi1_flag_rx */
- 0x158 (PIN_OUTPUT | MUX_MODE1) /* ssi1_rdy_rx */
- 0x15a (PIN_OUTPUT | MUX_MODE1) /* ssi1_wake */
+ OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE1) /* ssi1_rdy_tx */
+ OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1) /* ssi1_flag_tx */
+ OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */
+ OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE1) /* ssi1_dat_tx */
+ OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE1) /* ssi1_dat_rx */
+ OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE1) /* ssi1_flag_rx */
+ OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE1) /* ssi1_rdy_rx */
+ OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | MUX_MODE1) /* ssi1_wake */
>;
};
modem_pins: pinmux_modem {
pinctrl-single,pins = <
- 0x0ac (PIN_OUTPUT | MUX_MODE4) /* gpio 70 => cmt_apeslpx */
- 0x0b0 (PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* gpio 72 => ape_rst_rq */
- 0x0b2 (PIN_OUTPUT | MUX_MODE4) /* gpio 73 => cmt_rst_rq */
- 0x0b4 (PIN_OUTPUT | MUX_MODE4) /* gpio 74 => cmt_en */
- 0x0b6 (PIN_OUTPUT | MUX_MODE4) /* gpio 75 => cmt_rst */
- 0x15e (PIN_OUTPUT | MUX_MODE4) /* gpio 157 => cmt_bsi */
+ OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE4) /* gpio 70 => cmt_apeslpx */
+ OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* gpio 72 => ape_rst_rq */
+ OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4) /* gpio 73 => cmt_rst_rq */
+ OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE4) /* gpio 74 => cmt_en */
+ OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE4) /* gpio 75 => cmt_rst */
+ OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* gpio 157 => cmt_bsi */
>;
};
};
--
2.4.3
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
